Electric water heater Ariston 80 liters instruction manual. Ariston water heater (80 liters): model characteristics and their main advantages

18.10.2019

Models:

Ariston SHT30H Ariston SHT 50 H Ariston SHT 80 H Ariston SHT 100 H Ariston SHT 30 V Ariston SHT 50 V Ariston SHT 80 V Ariston SHT 100 V Ariston SHT-EL 30 H Ariston SHT-EL 50 H Ariston SHT-EL 80 H Ariston SHT -EL 100 H Ariston SHT-EL 30 V Ariston SHT-EL 50 V Ariston SHT-EL 80 V Ariston SHT-EL 100 V

1. Initial information by electric water heater

1.2 The device and the names of the main parts

2. Specifications

2.1 Wiring diagram

3. General Warnings

4.Installation instructions

4.1.3 Installation of vertical water heaters

4.2 Water connection

6.1 SHT electronic model

6.2 Mechanical model SHT

1. Basic information about the electric water heater

1.1 Scope and characteristics

Electric storage water heater designed to provide hot water. Ariston Shuttle series water heater, one of the essential accessories of modern life, is characterized by the following features:

1) The inner tank, made of high quality corrosion-resistant (stainless) steel, guarantees durability, corrosion and impact resistance;

2) high efficiency heating element with reliable insulation of the heating element;

3) protection against overheating and high pressure;

4) Easy to use intelligent control system.

1.2. The device and the names of the main parts

2. Specifications

2.1 Main specifications

Model	Volume, l	Voltage, V	Current strength, A	Power, W	Current frequency, Hz	Maximum pressure, bar	Water heater dimensions (LxHxB), mm	Packing dimensions, mm
SHT30H SHT30V SHT-EL30H SHT-EL30V	30	220	11.4	2500	50	0.6	603x380x270	670x470x352
SHT50H SHT50V SHT-EL50H SHT-EL50V	50	220	11.4	2500	50	0.6	898x380x270	965x470x352
SHT80H SHT80V SHT-EL80H SHT-EL80V	80	220	11.4	2500	50	0.6	985x450x310	1040x540x392
SHT100H SHT100V SHT-EL100H SHT-EL100V	100	220	11.4	2500	50	0.6	910x540x360	980x620x445

2.1 Wiring diagram

Mechanical Model SHT

3. General Warnings

Local codes and regulations may restrict the installation of electric water heaters in bathrooms. Merloni TermoSanitari cannot be held responsible for damage caused by incorrect installation by the user or by failure to follow the instructions in this manual. Installation must be carried out by qualified personnel. In particular, attention should be paid to the following points.

Electrical wiring must comply with the Electrical Installation Rules (PUE).

The safety valve supplied with the device must be in good condition and undamaged and must not be adjusted or replaced with a similar valve.

The heater must be installed by qualified personnel. The screws must be properly screwed into the plastic dowels.

Check that the mains voltage matches the specifications on the rating plate.

Check the correctness of the earthing done, in accordance with the current rules and regulations. The power outlet for the water heater must have a grounding contact and be properly grounded. Ground and neutral wires must be different and easily identifiable Attention: if the water heater is not grounded, then in the event of a short circuit, the RCD (residual current device) supplied with the kit may not work. This is dangerous!

Do not use any

The electric water heater must be powered from a separate electrical line from the power distribution board. Do not connect additional electrical devices to this line.

The power socket of the heater must be located in a dry place away from sources of splashing water.

An electric water heater uses a special power cord. If damaged, it must be replaced with a special power cord by a qualified technician.

To disconnect the heater from the mains, use a two-pole switch with a gap between open contacts of at least 3 mm.

4.Installation instructions

4.1 Installing the water heater on the wall

4.1.1 Installation position and wall requirements

The wall must support twice the weight of the heater filled with water. To reduce heat loss, the water heater should be installed as close as possible to the point of use of water. It is recommended to leave a free space of at least 50 cm around the water heater for maintenance.

Attention! The water heater is designed for indoor installation. If in winter time If you plan to use it, drain the water from it as it may freeze and damage it.

4.1.2 Installation of horizontal water heaters

You are taking optimal position on the wall for mounting the water heater. Be guided by the distance between the brackets C, indicated in the attached table.

Drill 4 holes for the strikers that are attached to the wall. Hole diameter ∅16 mm, depth 80mm.
striker

Insert plastic dowels into the holes. Next, using the screws inserted into the dowels, fix the strikers to the wall. Attention! When the head of the screw firmly presses the panel with hooks to the wall, stop screwing in so as not to damage the planks. Slowly keep lowering the water heater until it hangs on the wall; check the reliability of its fastening on the wall. When doing this, keep in mind the specified distance between the installation points of the slats.

4.1.2 Installation of horizontal water heaters

Choose the optimal position on the wall for mounting the water heater. Be guided by the distance between the brackets C, indicated in the attached table. Drill 2 holes for the strikers that are attached to the wall. Hole diameter W16mm, depth 80mm. For water heaters of 80 and 100 liters, 2 additional holes must be drilled. Insert plastic dowels into the holes. Next, using the screws inserted into the dowels, fix the strikers to the wall.
Attention! When the head of the screw firmly presses the panel with hooks to the wall, stop screwing in so as not to damage the planks.
Slowly keep lowering the water heater until it hangs on the wall; check the reliability of its fastening on the wall. When doing this, keep in mind the specified distance between the installation points of the slats.

4.2 Water connection

Screw the safety valve (A), which is supplied with the water heater, into the water heater inlet marked in blue (see fig. 7).
Connect the cold water line (B) to the lower connection of the safety valve.
Connect the drain pipe (C) to the relief valve drain. The free end of the drain pipe must be open to the atmosphere. Drain pipe must be slanted downwards and must not be pointed at the user.
Connect the hot water line (D) to the outlet of the water heater marked in red.
The inlet and outlet pipes must be designed for a water pressure of about 0.6 MPa and a temperature of 95 °C.
To prevent damage to the safety valve, do not screw it too tightly into the water heater.

If the pressure in the water supply network is close to the set pressure of the safety valve, install a pressure reducer on the water supply line at a distance from the water heater.
If a tap is installed in the cold water supply line, it must be constantly open.
During normal operation of the water heater, during heating, water may drip from the drain pipe of the safety valve, which means that the pressure is released from the device.

5. Actions after installing the water heater

Open the faucet in the cold water supply line, then open the hot water faucet on the faucet and wait until the outlet water flow is equal to the inlet water flow. This means that the water heater is filled with water. Close the mixer valve and leave the valve in the supply line open.
Attention! Before turning on the water heater, make sure that the tank is filled with water and there are no leaks in the system.
After filling the water heater tank with water and checking the tightness of the system, plug the water heater's waterproof electrical plug into the socket.

6. Electric water heater operation

6.1 Electronic model SHT=EL

Attention: Before turning on the water heater, make sure it is filled with water. Make sure that the water heater is properly grounded. Check the operation of the RCD (residual current device) that comes with the cable. Test instructions are located on the cable. The water heater control panel has an [On/Off] button, a [power] button, and [Plus] and [Minus] buttons to select the desired temperature. As well as an indicator of heating and the selected power.

Turning on:
Plug in the water heater. Within 1 second, all indicators will light up, then the current temperature in the tank will be displayed on the screen. The temperature display will flash. This means that the water heater is in the off state. Press the [on/off] key to turn on the water heater.

Power level selection:
When the water heater is on, press the [power] button. Pressing should be short. This will allow you to change the power from 2500 W (indicator is on) to 1500 W (indicator is on)

Antibacterial function:
When the water heater is on, press the [power] button for about 5 seconds. This will enable the antibacterial function. The heating indicator will flash. This function will automatically heat the water up to 750C and will maintain this temperature for 3 hours. The water heater will then return to the heating settings you set before entering the antibacterial function. This function can also be turned off by pressing and holding the [power] button for 5 seconds.

Temperature setting:
In the on state, when the numbers are no longer flashing, press the [Plus] or [Minus] button to check the temperature settings. At this time, the system will enter the temperature selection mode. The numbers on the display should flash rapidly. The temperature can be changed from 300C to 750C in 1 degree increments. Temperature changes are made by pressing the [Plus] or [Minus] buttons. The water heater will maintain the set temperature automatically.

Warning:
Since the system does not have a memory function, when the water heater is turned off, the temperature settings are reset. When you turn it on again, the default settings are set: heating temperature 750C and heating power 1500 W.

Error codes displayed by the system:

If the water heater is switched on when the tank is not filled with water (the so-called “dry” switching on), the system automatically reads an incorrect heating gradient and switches off the water heater. Error code E2 will appear on the display

If temperature sensor depressurization or a short circuit occurs, the system will display an error E3

If the temperature rises above 900C, the system will display an error E4

In case of problems, contact authorized service centers

6.2 Mechanical model SHT

The water heater control panel has an [On/Off] button, a [power] button and a heating temperature controller.

Turning on:
Plug in the water heater. By pressing the left button marked, the water heater is switched on and off. This key turns on the heating element with a power of 1500 kW. During the heating process, the left key will be illuminated. When the set heating temperature is reached, the button will turn off.

Power level selection:
When the water heater is on, press the left key marked. This key turns on an additional heating element with a power of 1000 W. Thus, the total heating power will be 2500 watts. During the heating process, the keys will be highlighted. When the set heating temperature is reached, the keys will go out. If the left [On/Off] key is pressed while the right [Additional power] key is pressed, the water heater will turn off and both keys will go out.

Temperature setting:
The water heating temperature can be adjusted using the temperature controller, if the water heater is switched on. Temperature control is carried out in the range from 300C to 750C. The water heater will maintain the set temperature automatically.

7. Moments that need attention

1. At the first start-up of the water heater, as well as at each start-up after switching off, make sure that the water heater is filled with water and only then connect it to the network.
2. If the power cord is damaged, it should be replaced with a special cord. This cord can be purchased from an authorized service center.
3. In winter and in cold areas, when the heater is not used for a long time, drain the water from the heater. To do this: close the cold water supply valve, open the drain cock (if there is a mixer, turn its regulator to the position maximum temperature), close the sludge drain (be careful not to scald), then drain the water.
4. Socket outlets must be properly grounded.
5. Clean the heater periodically during operation. Sequence of actions: disconnect the water heater from the network, shut off water faucet, open the drain valve by turning the handle, open the drain hole (be careful not to scald) and drain the dirt. It is advisable that this work be done by a qualified specialist.
6. If there is heavy scale formation in the heating elements or a large amount of sediment, remove the heating elements and clean them. When reinstalling them, observe the following: the bolts must be tightened evenly, without significant application of force, the fixing support must not be tilted. The power supply can only be connected after filling the water heater with water.
7. If the heater is not used for a long time, turn off the cold water supply tap and disconnect the water heater from the mains.
8. If the water pressure exceeds 6 bar, water drops or leaks may appear on the outlet of the safety valve.
The rare appearance of water droplets on the drain hole of the safety valve indicates normal operation of the heater.
The frequent appearance of water drops on the drain hole of the safety valve means that the water pressure is too high. In this case, it is necessary to install a reducer on the cold water supply pipe to reduce the pressure, which should be located at the maximum distance from the heater.
To drain the resulting water droplets, a drain pipe can be used, the end of which must point downwards and not be closed.
9. Before contacting the service center, make sure that the malfunction of the device is not related to the shutdown of the cold water supply, power supply, etc. If the water heater is not powered, the water overheating safety thermostat may have tripped. In this case, contact an Authorized Service Center. Have your warranty card ready. It will be needed by a service specialist during the repair of Ariston.

The presence of an autonomous water heating system provides not only comfortable living, but also independence from the whims of utilities. The performance of such systems, their efficiency and safety depends on the technical characteristics of the Ariston boiler, the connection scheme and the quality of the installation.

The key to a long and trouble-free service is compliance with all operating rules and timely maintenance. Ignoring the requirements prescribed by the manufacturer can lead to premature failure of both individual parts of the boiler and the entire product as a whole. In addition, the possibility of electric shock increases many times over.

The instruction manual contains all the necessary information regarding the installation, connection, conditions of use and the frequency of maintenance of the Ariston storage water heater. In addition, the document includes a list of the most common problems and a method for fixing them yourself, however, for effective solution problems will require knowledge of the design and basic principles of operation of the product.

The device and principle of operation of the water heater "Ariston"

A modern Ariston boiler for 30, 50, 80 and 100 liters is a hermetic structure consisting of the following parts and assemblies:

storage tank:
Electric heating element (TENA);
Magnesium or zinc sacrificial electrode;
Tuning and control unit;
Casing.

The inner surface of the tank must undergo anti-corrosion treatment. Depending on the cost of the product, various modifications may have as anti-corrosion protection:

Titanium coating;
glass-porcelain coating;
A layer of heat-resistant enamel resistant to aggressive compounds.

Besides, expensive models water heaters from the premium manufacturer "Ariston" can have all-metal welded storage tanks made of alloyed stainless steel.

The air gap between the casing and the inner container is filled with a polymeric heat-insulating composition (most often, polyurethane foam). Thermal insulation allows you to noticeably slow down the cooling process, thereby reducing energy consumption.

Heating elements are divided into two main types: "wet" and "dry". Wet are called heating elements that come into direct contact with the heated liquid. In the process of interaction with the working environment, a persistent coating of insoluble scale is formed on the outer surface of the heating element, which prevents normal heat transfer. A zinc or magnesium anode is used to protect the heating elements and the inner surface of the tank from corrosion damage.

The functionality, informativeness and ergonomics of the water heater from the company "Ariston" largely depends on the design and design of the control unit and settings. There are two types of control mechanisms: electronic and mechanical. Digital systems has an attractive appearance and differs in accuracy of adjustment, however, it is extremely sensitive to voltage fluctuations.

The mechanical unit looks “simpler”, and the adjustment accuracy is not the same, however, the reliability of such devices fully compensates for these shortcomings. In addition, the price of models with electronic adjustment is much higher.

The casing of the unit can be made of both metal and polymer materials. The most common is the cylindrical shape, but models of other configurations are in demand.

How to choose the volume of the water heater

Boiler capacity is one of the main criteria to consider. Customer reviews and statistical analysis allowed to determine the required amount of hot water depending on the number of consumers.

For one person, a 30-liter Ariston heater is enough. If two people live in one apartment at the same time, Ariston for 50 liters will fully satisfy the need for hot water. A family of three or four people will need "Ariston" for 80 liters. If we are talking about providing a private cottage or a small restaurant, the best option would be "Ariston" for 100 liters or more.

Operating instructions for the water heater "Ariston"

The beginning of operation can be considered the installation and connection of the boiler to a centralized cold water supply system and electrical network. The quality of installation depends on the safety, efficiency and service life of the product. If, for one reason or another, the boiler is put into operation on its own, special attention should be paid to the points below.

It is necessary to start work on mounting and connecting an Ariston brand water heater by carefully studying the instructions attached to it.

Since the power consumed by the device is quite large, it is necessary to make sure that the characteristics of the electrical wiring used for connection fully correspond to the expected loads and has. The best option for connecting to the mains is a separate cable from the switch cabinet or shield.
Do not use components with visual defects, damaged threaded sections, etc. The safety valve included in the scope of delivery deserves special attention.
Since the mass of the product is quite large, and the temperature of the water contained in it can reach up to +75 0 С, the boiler must be fixed to the bearing surface on metal diameter not less than 10 mm. It is allowed to use plastic dowels of the same load capacity.
Installation of supply and discharge pipelines must be carried out in strict accordance with the diagram attached to the heater by the manufacturer.
The place of connection to the power supply must be reliably protected from condensate, dampness and direct contact with water.
You can connect "Ariston" to the power supply only after filling the storage tank cold water, otherwise the water heater heater may fail.
If all the work is done correctly and the product is working properly, after switching on, the corresponding indicator should light up, indicating that the boiler is working.

Water heater Ariston: operation, maintenance and repair

To ensure efficient and safe work you must know and follow the basic rules for using the product.

It is forbidden to turn on the device until the storage tank is completely filled.
Mechanical or other damage to electrical cables is not allowed;
Before starting the operation of the Ariston water heater, make sure that the grounding is in good condition;
In the event of a malfunction, the unit should be immediately disconnected from the power supply, drain the water and contact the Ariston service center.

Even with proper operation, timely maintenance of the system is necessary to maintain operability. First of all, this is due to the low quality of the water supplied. Despite the presence of filters, a large number of chemical compounds and mechanical impurities that contribute to the formation of scale and other contaminants. Regular and internal surface of the drive will significantly increase the life of the boiler. Scheduled maintenance includes:

Preliminary draining of water from the storage tank;

Disconnection of plumbing fittings;

Dismantling the body of the water heater;

Cleaning the heating element and the inner surface of the tank without the use of particularly aggressive detergents, avoiding mechanical and abrasive effects as far as possible;

Assessing the condition of the magnesium anode and, if necessary, replacing it.

The conservation and subsequent activation of the boiler deserves special consideration.

How to turn on the Ariston water heater after winter: instruction manual

If the use of the device during the cold season is not planned, measures should be taken to preserve the system, and, above all, the water heater itself. For this you need:

Completely drain the water from the storage tank;
Disconnect the plumbing fittings from the inlet and outlet pipes;
Clean the heating element and inner surface tank;
Copiously lubricate the threaded surface of the nozzles with grease or other grease and wrap with rags or PVC film.

To turn on the Ariston heater after winter, you must:

Clean the pipes from grease residues;
Connect the device to the main pipelines;
Make sure that the grounding and electrical wiring are in good condition;
Fill the storage tank with cold water;
Turn on power.

Important! Connecting an empty storage heater to the mains is strictly prohibited!

Due to the simplicity of design, reliability and affordable price, Ariston for 30, 50, 80 and 100 liters is deservedly popular. Wide the lineup allows you to choose a model according to your needs and financial capabilities. However, we should not forget that only full compliance with the operating instructions and timely maintenance will ensure efficient work and prevent premature failure of the Ariston boiler.

The Ariston water heater is represented by a fairly wide sanitary assortment and the corresponding standard model lines.

Products of this brand have the following categories:

traditional boilers;
floor boilers;
condensing boilers;
floor boilers;
boilers with indirect heating;
instantaneous gas water heaters;
water heaters equipped with heat pumps;
storage water heaters on gas;

Each appliance is equipped with heating elements, control devices and additional accessories.

Why Ariston water heaters are created

Household appliances for heating water, which are powered by electricity, are most often used for the period when hot water is turned off. As a rule, they acquire compact models. When professionally installed, it provides a supply warm water for daily household needs: washing, cleaning or showering.

In private sectors, with all communications, they use gas and larger volumes with storage. In this case, household appliances of the most famous Italian company are used all year round.

How to turn on the water heater Ariston

Under no circumstances switch on an empty heater!

Most household appliances are characterized by the following instructions when first turned on:

Open the cold water supply valve (not to be confused with the safety valve);
Open the hot water tap or lever from the mixer connected to the water heater;
Wait a certain amount of time to collect water;
When the heater is filled, water should flow from the mixer;
Provide proper nutrition for the device;
At the first start-up, the temperature should be set in the middle position, over time, the liquid temperature level is adjusted to save and quickly heat up;
Electronic models Ariston is regulated by buttons for the required level of heating;

These steps must be performed by the installation wizard.

Due to inexperience, they forget to open the valve responsible for supplying hot water from the boiler. If it is not fixed in the desired position, then the heated water from the device will follow into the riser of the house.

Water heater repair Ariston

Ariston water heaters have vulnerable parts:

thermostat;
sensors;
switches;
heating elements.

Most often, valves and insulation gaskets are repaired. The integrity of the tank is violated less often. This failure occurs due to corrosion or careless handling. The tank needs to be repaired only in the service.

As an independent repair, timely preventive cleaning is implied. Every six months, it is recommended to clean the heater for the Ariston water heater.

How to determine the malfunction?

It's simple, with obvious changes in work:

Strange hissing during operation.
The standard heating period is extended.
Switching on and off noticeably increased.

Any high-quality Ariston device is easy to handle with self repair. But it's better to follow this guide:

De-energize the room and the device.
Drain the water. Drainage must be provided by a hose with a diameter slightly smaller than the liquid discharge hole.
Put the drain hose into the toilet.
Shut off the cold water supply.
Disconnect the hose from the cold water valve.
Connect this hose to a faucet and lower it into the toilet.
Remove TEN. Its fastening is always on a nut with a washer or a plate.
Having pulled out the heating element, carefully examine all places with scale and try to remove everything without harm to the tank.
After removing the scale, pour clean water over the tank.
If the heater itself is in working condition, then you can clean it in the same way.
Install all hoses and parts of the heater in the same order.

The budget and optimal way to wash off scale is lemon acid, diluted in water. This solution is poured into the tank and left for 24 hours.

With an independent approach, it is possible and necessary to replace parts only with original ones. Spare parts for the Ariston water heater from the manufacturer guarantee the quality, the money invested in repairs and the stable operation of the devices.

Modern appliances for heating water are classified, first of all, by displacement. Selection also begins with the volume of the tank. Each of Ariston models designed for specific premises and the frequency of inclusion. What is the difference between the models?

Models and displacement

Line of models:

VELIS INOX.

Original Specs:

stainless elements, including tanks;
characteristic difference - universal (simple) installation;
flat shape;
Ariston water heater is available in 30, 50, 80 and 100 liters;
there is a protection system on the power cord;
fuse from starting with an empty container;
additional equipment is equipped with protection against freezing or overheating;
branded heating elements are made of high quality copper;
load distribution function due to flasks and two heating elements of 1 and 1.5 kW;
maximum power 2.5 kW.

ABS VLS INOX QH

Outwardly similar to VELIS INOX, but has differences:

Ariston water heater for 30, 50, 80 and 100 liters;
improved design solutions;
equipment with electronics for rapid heating, antibacterial water treatment (ECO), temperature measurement;
water is processed in two tanks; in rooms with a large area, an Ariston water heater of this model of 100 liters is recommended.

VELIS QH

It has external similarities with ABS VLS INOX QH and VELIS INOX.

Model differences:

super-fast heating;
ease of design and use;
LCD - display;
soft touch function (automatic saving);
water is heated in several stages;
internal tanks are covered with steel;
three heating elements (heating elements);
Ariston water heater for 30, 50, 80 and 100 liters.

ABC VELIS PW

Original Specs:

safety shutdown (ABS0);
bacterial protection (ECO);
the inner tank is covered by latest technology AG+;
special welding method during the assembly process;
two heating elements;
heating in two containers.

PRO ECO INOX PW V SLIM

Original Specs:

water pressure function;
stainless steel;
model SLIM, diameter is only 353 mm;
internal tank with a special antibacterial coating;
installed at points with cold water pressure, any level of pressure is suitable;
low power (up to 1.5 kW).

ABS PRO ECO INOX PW

Original Specs:

Ariston heaters for 50, 80 and 100 liters;
narrow cylindrical shape;
simple installation;
electronic control;
external and internal parts from stainless steel;
testing for 16 atmospheres;
7 years warranty.

ABS PRO R INOX

Original Specs:

mechanical thermostat;
Ariston heaters for 30, 50, 80 and 100 liters;
a magnesium anode was installed to protect against corrosion and scale concentration;
external heating control;
protection against water drops;
water resistance;
one of the most economical models.

ABS PRO ECO PW SLIM

Original Specs:

Ariston heaters for 30, 50, 65 and 80 liters;
narrow forms of a water heater;
economical energy consumption, the tank of the model was tested for strength under a pressure of 16 atmospheres, a good margin of safety;
equipped with all security systems.

ABS PRO ECO PW

Original Specs:

Ariston heaters for 50, 80, 100, 120, 150 liters;
suitable for kitchen sink, full-fledged home or cottage;
equipped with all protective security systems;
additional heating element.

ABS PRO R SLIM

Original Specs:

the convenient shape of the cylinder allows you to mount the heater in any corner of the room;
Ariston heaters for 30, 50, 65 and 80 liters;
"folk", budgetary and suitable in size water heater;
with a diameter of 35 centimeters;
fast heating;
the presence of a safety valve;
all water protection systems, switching on without water;
the price of an Ariston Water Heater of such a model of 80 liters is only 8800 rubles.

Original Specs:

instant heating;
practicality;
compactness;
affordable;
the possibility of horizontal and vertical suspension;

Typical instructions for a water heater Ariston 80 liters

Water heaters of this volume are necessary for daily use by the whole family. Presence of sensors and temperature level guarantees safe operation.

A complex and responsible event in the installation process is the wiring. Most often, the wires need to be lengthened, because the factory cable is not long enough.

For long-term use of the device, it is necessary to carry out installation according to all the rules or with the help of an experienced craftsman. To avoid breakdowns and other troubles, follow the rules of operation:

The first switching on and switching off is carried out with a filled tank.
If the batteries are damaged, be sure to replace the weak parts.
In a room with a minus temperature, it is necessary to drain the water from the heater.
Long periods of inactivity of the appliance without heating function should be carried out with a closed tap or valve supplying water. Also, heaters must be unplugged from the outlet.

Devices for high-quality water heating from Ariston are presented in user-friendly sizes, equipped with all kinds of engineering improvements and are available in all major retail chains. It is enough to choose the model you need for individual installation.

Overview of the Ariston Velis PW 50 Water Heater - video

Today, Ariston water heaters are one of the most popular on the market. In particular, the 50 liter models are in particularly high demand. Such water heaters have small dimensions, so they can easily fit in any room. Ariston water heaters are easy to operate, maintain and have a long service life.

Peculiarities

Ariston heater able to heat water from +30 to +85 degrees. An interesting feature of this product is that such a water heater has an extremely pleasant and user-friendly design, able to fit into any room, and constantly provides a home hot water. Many models also have an energy saving function - the water automatically heats up to a temperature of +50 degrees. Of course, you can increase this figure if you wish. Also, Ariston 50 liter boilers can automatically turn off when there is a power surge, which helps prevent damage to the unit. V modern models it is worth noting the functions of accelerated heating and water filtration.

Kinds

Among the main models of Ariston water heaters, there are several types.

Water heaters accumulative type. Two tubes and power supply are connected to the storage heaters. The first tube is designed to supply cold water to the boiler. After heating it, it exits through the second tube. Typically, 50 liter models are mounted - they are attached to the wall. Water in these types of boilers is heated by electricity. Thanks to the thermostat, the storage electric boiler automatically turns off after the liquid is heated to desired temperature. Users marked storage boilers Ariston VLS, which, among other things, are flat. They are extremely compact, so they do not take up much space.

Boilers of gas type. Gas models differ in that they heat water not at the expense of electricity, but with the help of gas. Otherwise, the device and the principle of operation are similar to storage-type water heaters. It should be noted that the gas boiler is usually made of steel and is additionally covered with a layer of titanium enamel, which allows both to increase the reliability of the water heater and reduce heat loss.

Water heaters with indirect heating. They carry out heating of water by means of the coil installed inside. It is noted that these models heat water faster than all previous ones. But usually they are quite large and have big weight, but they are able to heat a large amount of water (150–500 liters). Such volumetric models are not recommended to be fixed to the wall, but placed on the floor. The floor water heater has a very durable coating that increases its service life.

Among other types of Ariston boilers, it is worth noting flat devices. These compact models have minimal dimensions, they can be placed anywhere. Despite their small size, these boilers are quite powerful. This option organically fits into the room of any size and does not take up much space. And also the manufacturer offers customers rather unusual boilers that can be positioned horizontally. Horizontal models can be placed in a specially designated niche, thereby completely hiding it, which allows for even greater savings in usable space.

Popular Models

It is worth highlighting some of the most common models of Ariston boilers.

Ariston Velis Inox. This model has horizontal and vertical variations. Stylish design and a flat body make the boiler a rather attractive technical device that does not take up extra space.

Ariston ABS VLS. This option is almost completely automatic. Installed in the device various systems, which monitor the temperature and protect the heating elements from overheating.

Ariston ABS PRO. This type of water heater is cylindrical in shape, which allows you to place it in the corner of the room. This version of the boiler is one of the most budgetary.

How to connect?

Usually, the installation and connection of Ariston 50 liter boilers does not cause great difficulties. Each device is accompanied by an instruction manual. Therefore, installing a boiler is a simple matter and can be done with your own hands.

Installation of a mounted boiler is carried out as follows:

measurements must be taken on the wall, including determining the height of the unit;
then a pair of holes should be made with a puncher, which should be approximately 10 cm in depth;
for fastening the boiler, strong anchors are used that can withstand the heavy weight of the structure;
then the boiler is simply hung on the anchor with a special mounting plate, which is located behind the body.

One of the main points when installing a boiler is to correctly connect and carry out the first start of the device, using rules such as:

first you need to open the valve to supply cold water to the boiler;
then open the mixer, from which hot water; most likely, at the first start it will produce loud and intermittent sounds, but do not be afraid - this is normal for the first inclusion;
then you need to wait a bit until the boiler carries out a set of cold water to heat it;
after filling the boiler and heating the liquid, the water from the tap must flow stably; it is advisable not to immediately set a large temperature regime;
After the first start, the water temperature can be easily adjusted using simple commands on the water heater.

Faults

Even the most reliable equipment is not immune from accidental breakdowns. No matter how high the characteristics of the device, it can still fail. Various factors can influence this. Water heaters are usually characterized by breakdowns of water heating elements and thermostats. In order to avoid damage to the heating elements, it is recommended to carry out preventive maintenance and cleaning of the heating elements at least once a year. A long period of water heating, extraneous sounds during boiler operation, or more frequent spontaneous shutdowns can serve as an indicator of a malfunction. Boiler repair can be done independently; To do this, you need to disassemble the unit and determine the location of the breakdown.

In order to eliminate the malfunction with your own hands, you must follow certain steps.

To begin with, it is worth disconnecting the device from the mains, and then completely drain the water from it. To do this, you can use a hose that connects to a special hole for discharging water.
Shut off the flow of fluid into the boiler. After draining the water, you can begin to inspect the parts of the water heater.
Often breakdowns occur precisely in electric heaters, so you should immediately inspect the heating element (heater).
With prolonged use, any heating element is covered with scale. Therefore, it should be carefully removed, while you can use special tools.
If replacement of any components is necessary, then it is necessary to purchase only original parts by contacting the official manufacturer.

In some cases, a water heater tank may leak. In this case, you need to carefully examine the body of the product. It is possible that the problem lies in a leaky gasket, which should simply be replaced with a new one. But if the heater tank is leaking due to a crack or chip, then it is unlikely that it will be possible to eliminate this malfunction by independent forces. You can try using the soldering method, but this is unlikely to help for a long time. If the housing is damaged, corrosion in the heater begins to occur faster, and heat loss begins to increase.

Therefore, the installation of the heater should be carried out very carefully so as not to accidentally damage the housing. If such a problem still occurs, then best solution will contact the service center.

After analyzing customer reviews on the use of Ariston boilers, it should be noted that most of the owners are satisfied with the purchase, because the operation of such a water heater does not cause serious complaints. Customers appreciated the stylish appearance, compactness and ease of operation of the water heater. They were also separately noted low level heat loss, low electricity consumption during boiler operation. In general, the owners of Ariston boilers noted good value for money, as well as professional service in specialized services.

As negative points periodic breakdowns of the water heating element were noted. Usually manufacturer Ariston gives a guarantee for the heating element up to one year. Some owners of boilers have had breakdowns before. But the performance of this element depends on many factors - frequency of use, water hardness and others. And also among the negative aspects, it is worth noting the lack of elements for mounting some wall-mounted boilers in the kit. These brackets must be purchased separately.

The history of the Italian company Ariston dates back to 1930. Then the product range was limited only to scales, but today it includes multifunctional household and professional appliances. Among the favorites is a reliable and durable Ariston water heater. It differs from competitive technology in a key ratio of qualities for consumers - price-quality.

Long history

In 1930, thanks to the quick-witted Aristide Merloni, a new brand appeared on the household appliance market - Ariston. The family business specialized in the production of scales. A little later, the assortment was replenished with electric heaters, cylinders for liquefied gas. Flowing and storage water heaters in the catalog on the official website appeared relatively recently. Further, the business was transferred to the sons of the founder - Vittorio, Antonio and Francesco. As a result of the division of the company, there were three main divisions:

Ardo;
Merloni Elettrodomestici;
termosanitary.

All companies specialize in the production of equipment under the brand name Ariston. Until today, one of the divisions has been intensively acquiring shares in other enterprises, expanding its composition, assortment and approaching the main market competitors - Bosch, Siemens, etc. The repurchased brands include the well-known Indesit and Scholtes, as well as 50% of GDA, which produced household equipment Hotpoint.

Today, factories in different countries are engaged in the production of instantaneous and storage water heaters Ariston, as well as other equipment:

Poland;
Russia;
Turkey;
Italy;
France;
Portugal.

In terms of turnover, this holding ranks third in the world ranking.

Rating of the best models of Ariston water heaters

The official website of the company is full of various Ariston water heaters. They differ in price, installation method, technical specifications, principle of operation and design. According to these criteria, a model range of the most successful variations was selected, both in the opinion of specialists from the service center and users.

Ariston ABS BLU EVO RS 30

The Ariston 30 heater has funded system heating. His small size 44.7x44.7x41 cm allow installation in a vertical position under the washbasin. The storage water heater of 30 liters is powered by a voltage of 220 volts, while consuming a power of 1.5 kW.

Ariston ABS BLU EVO RS 30

Thanks to the latter indicator, the device is able to heat water up to a temperature of 80 ° C, and it takes only 70 minutes to get the optimal temperature of 45 ° C. As an additional function, there is a thermostat and an overheating protection function. The price of Ariston 30 liters is 5800 rubles.

Ariston ABS VLS EVO QH 80 D

The Ariston 80 l water heater has a storage heating system with an electric tubular heater. It can be installed both vertically and horizontally. Boiler Ariston consumes power of 2.5 kW from a power source with a voltage of 220 V.

Ariston ABS VLS EVO QH 80 D

The device is capable of heating water up to a temperature of 80°C. EVO Ariston 80 liters is equipped with a stainless steel coated tank. Separately, it should be noted the protection system against overheating and starting without water. Equipment dimensions 50.6x106.6x27.5 cm, weight - 27 kg. There is an Ariston water heater of 80 liters - 16,000 rubles.

VIDEO: Overview works by Ariston ABS VLS EVO QH 80 D

Ariston ABS Andris Lux 15 UR

The Ariston water heater for 15 liters has a boiler with a silver coating on the inside. The electric device has a rated power of 1.2 kW, thanks to which the heating element is able to heat water up to a temperature of 75 ° C.

ABS Andris Lux 15UR

The device is installed on 15 liters under the sink, due to this you can save a lot of usable space. The cost of a storage electric water heater is 7,000 rubles.

VIDEO: Overview of ABS Andris Lux 15 UR

Ariston 50 ABS VLS Evo Inox

The water heater for 50 liters has an attractive design and small dimensions of 50.6x27.5x77.6 cm. The design includes an immersion heating element, which has a power of 2.5 kW. Ariston for 50 liters can heat water up to a temperature of 80 ° C.

Ariston 50 ABS VLS Evo Inox

The device operates from a power supply with a voltage of 230 volts. Electric water heater Ariston is equipped with a display, safety valve. The price of the apparatus for 50 liters is 21,500 rubles.

VIDEO: Ariston 50 ABS VLS Evo Inox review

A capacious storage water heater Ariston for 100 liters is installed on the wall surface. Its dimensions are 125.1x50.6x27.5 cm. The design includes an immersion tubular heater. The device is equipped with an electronic display that shows all operating modes and other necessary information. Inner part the tank is covered special material Ag+, and an enameled heating element is also built into it.

Ariston 100 liters ABS VLS EVO

The 100 l storage water heater has a double boiler system, so that the water warms up much faster. Already 29 minutes after switching on, you can take hot shower. The intelligent system of the device automatically remembers all heating cycles, so the equipment will prepare water by the time it is used most often. The price of a model for 100 liters is 19,900 rubles.

VIDEO: Overview of Ariston 100 liters ABS VLS EVO

Ariston ABS VLS Inox PW50 (cumulative)

This is a horizontal 50-liter apparatus, which has a flat rectangular shape which makes it perfect for small rooms. In addition, it has the ability to work with several water intake points, which makes it possible to create autonomous system heating water for all faucets installed in the house.

Ariston ABS VLS Inox PW50

The power of the equipment is 2.5 kW, it has 2 heating elements. As a safety feature, Ariston 50 liters uses a device shutdown system with an empty tank and overheating. The nominal liquid heating temperature is 80°C, and the outlet pressure is 0.2-8 Atm. In online stores, such equipment is sold at a cost of 19,000 rubles.

VIDEO: Ariston ABS VLS Inox PW50 work overview

Problems and malfunctions of Ariston water heaters

Ariston equipment is rightly considered reliable, able to work for many years without causing inconvenience. However, regular maintenance and preventive inspection of the equipment is necessary.

Among the main faults are:

failure of the electronics - only the sensor, heater or switch may break, or maybe all at once;
during operation, the machine may knock out, which means that the equipment lacks “cash” voltage - for correct operation, you will have to turn off all powerful electrical appliances in the house for the duration of the wash;
the problem with the ignition may be poor-quality wiring.

All problems are solvable, but on condition that repairs and maintenance are carried out by service specialists.

VIDEO: Why the boiler does not turn on and does not heat