Boiler ariston instructions for use. General information on Ariston water heaters

The firm "Ariston" specializes in the production of water heating equipment. Water heater "Ariston" 80 liters (instruction attached to the device), as well as other models of devices are widely known to the inhabitants of our country. Each new model has more stylish design and produced according to the latest technologies.

Figure 1. Ariston water heater for 80 liters

Characteristics of water heaters

All models of water heaters of the company have a very long service life. This effect is achieved by coating the inner walls of the device. modern materials which protect the boiler from rust. Cold and hot water do not mix inside, so it is possible to constantly maintain the temperature of the liquid inside the unit. Built-in temperature sensors are designed to protect Ariston from overheating. At the moment of a sharp change in the mains voltage, a protective device is activated and disconnects the boiler from the network. A special thermal insulation layer that keeps the water hot saves electricity or gas.

Some models of heaters have protection against bacteria. Water in such devices is always clean. Sometimes it happens that there is no water in the plumbing system. In this case, the device cannot turn on. Again, a special protection system will not allow him to do this. Almost all models of the company, including Ariston 80, 100, 30 liters, are equipped with the functions listed above. Main differences different models consists only in the external design of the devices. The body can be flat, round, horizontal, vertical. Any of them fits perfectly into the interior of the room (Fig. No. 1). Internally, their device is exactly the same (Fig. No. 2):

• internal boiler;
• thermal insulation layer;
• branch pipe for water inlet and outlet;
• magnesium anode(Fig. No. 3);
• thermostatic thermostat.

Figure 2. The device of the Ariston water heater for 80 liters.

Boiler is a tank for receipt cold water. Outside, it is closed by an outer casing. The water entering the tank is heated by a built-in heating element. Sometimes there are 2 heating elements. This is if an electric water heater. Between the boiler and the outer casing there is a layer of thermal insulation. In general, the design resembles a thermos device. The water in it retains its temperature for a long time. It comes out through the outlet tube. Ariston 80 also has a magnesium anode. It is installed to prevent deposits of mineral salts on the inner walls of the tank. It should be changed as needed. You can see this when cleaning the heating elements (Fig. No. 4).

When the water is heated to the set temperature, the thermostat disconnects the device from the network. The operation of the unit is monitored using an indicator light. The built-in thermometer allows you to monitor changes in water temperature. This is how the Ariston 80, 50 liter, 100 liter and other models are arranged. Their operating instructions are the same for any model. Each instrument is supplied with an instruction manual. It must be carefully studied, then the device will work for many years.

Figure 3. Magnesium anode.

Purpose of water heaters

Installation of a boiler in the house is carried out to provide housing hot water. The heater can be selected in 100 liters, 80 or smaller sizes. Everything Ariston models have the same internal structure, therefore, the connection diagram of the water heater is used the same for this series of devices. It is better to invite a specialist to install the device. If you decide to do it yourself, the work should be done according to the plan:

• inspect the device from the outside;
• prepare fasteners;
• check grounding;
• place the outlet correctly.

Figure 4. Cleaning the heating element of the Ariston water heater.

When inspecting the device, it is necessary to check the safety valve well. It should not have visible flaws. If they are found, the valve must be replaced. As fasteners, it is recommended to use plastic dowels and self-tapping screws for them. You need to connect a heater for 100 liters or any other to a separate power line. The outlet must be located in a dry place. The use of extension cords is prohibited.

Properly installed storage boilers start immediately after they are connected to the network. This is indicated by the illuminated indicators. The temperature of the water inside the device is also shown by thermometers.

Conclusion on the topic

There are many systems for providing hot water to private houses and country houses.

The most famous high quality devices are produced by Ariston.

There are many models, but they all have the same internal structure. Instructions for use of these devices is also the same for all brands. Storage devices for heating water differ only in external outlines. All characteristics of different models are also the same. Only the 80 liter model can still use the antibacterial function. To activate it, you just need to press the "power" button and hold it in this position for 5 seconds. The water temperature can be set between 30-75 °C.

Each time you turn it on, you need to control the water level in the boiler. When turning off the boiler for a long time, you need to drain all the water from it. Each device comes with a 1 to 2 year warranty. Repairs are made in almost every city with a warranty card.

The Ariston water heater is designed according to the latest technologies, has not only a high-quality water heating tank, but also good technical characteristics. The main advantages of such a boiler are durability and reliability, intuitive control and convenient operation. Each device is necessarily supplemented by a detailed instruction manual, which allows not only to independently install and connect the water heater, but also to perform simple repairs with your own hands.

Electric water heater Ariston: technical characteristics of boilers for 50, 80 and 100 liters

Ariston produces more than seventy models of storage water heaters with a capacity of 10-200 liters. The storage electric water heater is represented by several models, among which the 50.80 and 100 liter series are especially popular.

	Volume (liters)	Heating time up to 45°C (min)	Protection class IPX	Dimensions (mm)
ABS VELIS INOX QH D
ABS PRO ECO INOX POWER SLIM
ABS PRO ECO INOX POWER
ABS BLU ECO POWER SLIM

Water heater Ariston: installation (video)

Gas boiler Ariston

Price gas equipment depends on the principle of the water heater and its type. Each boiler is arranged in the same way, but it also has some features:

• DGI water heaters have electronic ignition and manual control of power indicators. Characteristic is the natural removal. The gas water heater has a concise rectangular shape;
• Fast-CF does not need additional power supply, and copper is used for the manufacture of the heat exchanger, which can significantly reduce heat loss;
• Marco Polog7s features a closed combustion chamber, providing additional safety of operation. There is a touch screen and modern design, which makes the model the most popular among consumers;
• Marco Polo M2 is a model with a combustion chamber open type and a smoke exhaust fan. There are a couple of stages of device protection that prevent overheating and guarantee high performance safety and long service life.

Before installing the device, you must familiarize yourself with the principle of operation of the Ariston water heater, as well as study the instructions with detailed instructions individual characteristics installation.

Boiler Ariston: device and principle of operation

The manufacturer uses proprietary protection against corrosive changes. Everything budget models equipped with a mechanical regulator, and each expensive water heater is equipped with a digital control unit. An internal temperature controller works inside the water heater, which allows you to optimize heating. The device and principle of operation of such equipment are as follows:

• an internal tank or boiler designed to receive cold water and framed by an external casing.
• built-in heater designed to heat incoming water;
• heat-insulating layer located between the body of the water heater and the boiler, which performs the function of a kind of thermos and allows long time keep the temperature indicators of heated water;
• a shortened branch pipe equipped with a divider for water supply;
• outlet pipe;
• built-in magnesium anode to prevent strong deposits in the form of mineral salts on the walls inner surface tank.
• thermostat designed to automatically interrupt the power circuit after heating the liquid to the specified temperature.

Control of the operation of water heating equipment is carried out by means of a voltage indicator, and with the help of a built-in thermometer, you can monitor changes in temperature indicators.

Ariston water heater user manual

Convenient connection of water-heating equipment from the company "Ariston" consists in the use of manufacturers of an autoclave special flange mechanism. The basic principle of operation of such a mechanism is based on pressing the gasket under the influence of water pressure. As a result, it is possible to completely eliminate not only the leakage of liquid, but also the formation of watery smudges. To avoid unnecessary heat losses, the fixing of electrical models of the water heater from the company "Ariston" is carried out in close proximity to the output point.

Overview of the water heater Ariston (video)

Optimal standard diameter fastener must be 10 mm or more. Installation of 100-liter hot water tanks has some features. In this case, fastening must necessarily occur with fixation on the other side of the wall. It is for this reason that experts recommend installing water heaters before the start of the main finishing works.

Important to remember, that when connected different types metals, it is mandatory to use dielectric adapters, through which differences in the degree of expansion of materials differing in parameters are compensated. It is necessary to connect the input using a standard valve, and a branch pipe is installed on the output. At the final stage, the installed water heater must be turned on and checked for correct connection, no leaks and operability.

During the operation of water heaters manufactured by Ariston, difficulties do not arise, but it is necessary to take into account some rules that affect the durability of the device and its performance. Periodically, preventive measures are taken, including inspection of the internal parts of the equipment, descaling and replacement of the heating element that has become unusable. average duration the operation of all mechanisms of a particular model can be found in the manufacturer's instructions. It must be remembered that the timely replacement of the anode allows you to extend the life of the water heating mechanism. In accordance with the recommendations of professionals, it is not advisable to set the thermostat to the maximum heating level.

If you set the temperature limit by about 10 ° C below the maximum values, then you can significantly reduce the cost of electrical energy, as well as save the resources of equipment parts. It is important to remember that you can disassemble the device yourself only as a last resort. Do-it-yourself repair work will result in the exclusion of the possibility of exercising the right to warranty repairs.

Do-it-yourself Ariston boiler repair

Repair work related to the elimination of breakdowns in gas appliances require the involvement of qualified specialists, and the repair of an electric boiler can be done independently.

Major mechanical failures are most often manifested by tank leaks., from which water begins to ooze or drip during operation. The cause of this failure may be corrosion in the areas of the welds or a malfunction of the reverse protection system of the valve, which operates and performs an emergency reset. In this case, it is necessary to eliminate the excess level of water and air pressure by means of a reducer. Any depressurization of the storage tank will require the purchase of a new tank. If such a defect is insignificant, then it is enough to replace the sealing gasket.

A rather inexpensive measure is the independent replacement of some electrical parts, including a heating element, a bimetallic thermostat, sensors or switches. In case of prolonged heating, noise or hissing, as well as in case of activation of the ABS system shutdown protection, the replacement of the heating element is required, the average service life of which does not exceed five years. Replacement is carried out after de-energizing the device, draining the water and removing the flange.

It is very important to systematically check the magnesium anode, which is consumable and intended for effective protection the inner surface of the tank and the heating element from corrosive changes. When the anode is thinned by ½ of the original volume, a mandatory replacement is carried out. The heating element is able to last much longer if the so-called “dry” heating element is installed in the structure.

Water heater repair Ariston (video)

Ariston, a well-established manufacturer in the water heating equipment market, has been a leader for a long time and offers the consumer only high-quality and very reliable products in a wide range. And the presence of the largest network of service centers in many cities of our country allows you to easily receive qualified assistance, as in repair work and maintenance of water heating equipment.

Ariston Company is the largest manufacturer household appliances which started its work in 1975. The president of this organization is the Italian Vittorio Merloni, who is also its founder. In 1980, Ariston became the European leader among manufacturers of household appliances and electronics.

Advantages of water heaters:

1. Security. adapted to almost any working conditions. They are also equipped new system security to prevent emergencies.
2. Durability. Long service life of heaters is ensured by quality materials from which they are made. This is mainly stainless steel with protective welds, as well as a steel tank with a titanium coating.
3. Ease of use. On the front panel of the boiler there is simple system control, with which the desired heating temperature is set. Also, a malfunction indicator is installed in the water heater panel, which gives a certain signal in case of improper operation of the unit (overheating, incorrect thermostat operation, switching on without water, etc.)
4. Profitability. Ariston water heaters have the lowest energy consumption rates. Average electricity savings are 35%.
5. Bacteria protection. Very often, water stagnates in heaters, in which bacteria multiply over time. The ECO protection built into the water heater prevents the appearance of bacteria not only on the walls of the device, but also on its internal elements.
6. High intelligence. The presence of the LCD display makes it possible to set the desired operating mode: day, night and economical.

The lineup

Flat boiler Ariston

The range of water heaters is quite huge and is constantly updated. They are very compact, although they have a large displacement. For a family of four, an 80 liter tank is ideal.

Mechanically controlled square tanks are very common. The only drawback is the unimproved fastening mechanism.

There are also models with a maximum capacity of 100 liters. Such units are able to provide industrial shower rooms. The insulating layer of such models is made of polyurethane foam.

The range of Ariston water heaters can have both an enhanced electronics system and a simple control mechanism. The warranty for volumetric tanks is given on average for seven years. For additional fastening boilers are made of special metal frames.

Main selection criteria

1. Thermal insulation material.
2. control method.
3. What material is the tank made of?
4. Power consumption.
5. term and method of use.
6. The presence of a protective system.
7. Quantity and quality of heating elements.
8. Water heating time and its maximum temperature.

The cost of a water heater depends on such factors: manufacturer, tank volume, materials of manufacture, power, warranty, additional functions. The prices of electric boilers range from 5,000 to 10,000 rubles. Concerning gas water heaters, then their cost ranges from 13,100 to 23,500 rubles.

Device and specifications

Boiler diagram

Boiler Ariston 80 liters- This is the most common option in home use. It consists of the following parts: housing, container and heating element (heater).

The inner and outer tanks of the device are separated by a layer thermal insulation material. Two pipes are connected to the heater, which are designed to supply cold and hot water. Together with the heating element, a magnesium anode is located in the heater, which prevents the deposition of scale in the device. Experts recommend periodically replacing the anode so that the water quality does not deteriorate.

As for the shape of the body, the 80 liter boiler is basically flat. In order to ensure the heating of water to a predetermined temperature, a special thermostat is built into the water heater.

Specifications:

1. High durability to corrosion.
2. Reliable isolation heater.
3. Overheat protection.
4. The presence of flashing indicators, which indicate the operation of the device.
5. Power level adjustment devices.
6. Maintaining the set temperature in automatic mode.

The boiler socket must always be in a dry place.

User manual:

1. The boiler comes with a safety valve., which must always be in an integer state. In the event of any chipping or other damage, the valve must be immediately replaced with a new one.
2. Water heater mains socket must not have a ground contact, otherwise, in the event of a short circuit, the boiler will burn out.
3. The use of seals is prohibited. and adapters.
4. It is not recommended to replace the plug water heater.
5. Water heater power, should occur only on a separate power line.
6. If you need to replace the power cord, it must be the same brand as the previous one.
7. Disconnecting the heater from the network should only be done with a two-pole switch.

heating element for boiler

Each boiler is equipped with a heating element. The device and characteristics of the heating element may be different, but most of all for an 80-liter Ariston water heater, a heating element of 1500 W on an oval flange is suitable.

It is made of stainless steel and has a curved shape. Inside the structure there is an oval flange, the size of which is 9.1 × 64.5 mm. The manufacturer of this device is also Ariston.

The heating element has the following technical characteristics:

1. Power - 1500 watts.
2. Voltage - 220W.
3. Warranty - 1 month.

How to clean the boiler?

To clean the water heater, you will need the following tools: knife, flashlight and a metal brush for washing dishes. First, you need to disconnect the heater from the power supply. You also need to turn off the water supply throughout the house or apartment.

Then, you need to remove the cover, which is located at the bottom of the tank, and disconnect all the wires there. All water is drained from the tank through a hose attached to the drain valve. At the bottom of the tank there are bolts that must be unscrewed, while substituting any container.

For thorough cleaning of the boiler, the electrical part is removed from it. You need to take it out very carefully so as not to catch the rubber gasket. The removed electrical part must be cleaned with a special iron mesh, or with a certain chemical agent.

The next stage of cleaning is to remove scale and debris from the tank. To do this, you need to completely inspect the cavity of the tank (with a flashlight) and clean out all the debris with your hand.

The cleaned tank must be thoroughly dried, after which it can already be collected in its original state. Also, before starting work, you should check the tightness of the tank.

If rubber gasket does not pass water, so the boiler can be put into operation.

For the convenience of quickly obtaining hot water in the room, regardless of central heating, storage electric water heaters - boilers were developed. The range of electric heaters is very wide. Today we will take a closer look at the instruction manual for one of them, namely, the Ariston water heater.

Your task is to use it correctly

Having purchased Ariston electrical equipment for the home, do not forget to carefully study the instructions and always have it "at hand". Follow instructions should not in any way be skeptical and underestimated, since it is, first of all, your safety. Even if you accidentally lost the instructions from the device, you can get its electronic version specifically for your Ariston model on the official website of the manufacturer. People who create electrical devices, test them, test them, put the maximum useful information to the manuals for use and operation with the only important goal- so that you use them correctly. The same article will discuss General requirements and introductory moments.

Boiler diagram Ariston 50

Boiler designs have approximately the same construction scheme. It has a body, a water tank (the boiler itself), and a heating element (otherwise a heating element, sometimes there are several of them in the configuration). Be sure to install a magnesium anode next to the heating element, which prevents the formation of scale. The boiler itself from the outside and in its inner part has an insulating layer.

Two pipes lead to the water heater - one for supplying hot water, the second for cold. Boiler bodies can be cylindrical or flat. The boiler tank can have a different capacity - from 30 to 100 liters. The basic principle of operation of the boiler is to heat the water in the tank and maintain its constant temperature, set by a person, depending on the need.

What you need to know about Ariston boilers

The main function of Ariston water heaters is to provide houses, apartments, cottages, cottages with hot water for household purposes. In order for the electric water heater to serve for a long time and with high quality, the following characteristics:

It should be noted that the instructions for water heater models that differ only in the system of different volumes of the same series are almost identical. There are two types of heaters according to the principle of operation: flow-through (the heat exchanger heats the temperature instantly as soon as you open the tap) and storage (water is drawn into the tank and then heated). Storage water heaters, or boilers, have compact tank, designed for different volumes - 30, 50, 80, 100 liters. Boilers are of direct heating (they themselves heat water using gas or electricity) and indirect (such devices are located near the heat exchanger, for example, a boiler).

Installation of the device must be carried out by a specialist, otherwise your equipment will lose the right to warranty service. After installing an electric water heater check the following:

About installing an electric water heater Ariston according to the instructions

Before installing the water heater, make sure the wiring can handle the added power. It is especially important that the outlet to which you are going to connect the device is grounded and not in contact with water. The power supply to the water heater must go from the shield on a separate cable. When choosing a place to install an electric water heater, consider its weight together with water in three times the size and the strength of the walls.

For fastening, hooks with a size of at least 15 mm are required. It is recommended to install a water heater in the immediate vicinity of the displacer, which will also reduce heat loss when water is supplied to the point of analysis. The distance from the ceiling is at least 10 cm, the space around the device is within a radius of at least 50 cm for technical work.

Under what conditions should the device not be installed?

If the water is hard, you must additionally install a filter, otherwise the water heater will quickly fail. The appliance must not be installed indoors temperature regime which may have a negative indicator, exclude the influence of factors dangerous for the device - dampness, frost, direct sunlight, dust and insects. Maximum avoid splashing water, steam on the body of the device, that is, it is not recommended to install it directly above the bathtub.

With a weak water pressure, it is necessary to set the maximum temperature, otherwise the device may not turn on at all.

Only branded parts

All parts of the water heater, when first installed, must be in good condition. This is especially true for the safety valve. If damage is noticeable, the part should be replaced with a similar one. In no case do not use adapters or extension cords, do not replace the water heater plug with another one. Separate power line required to power the boiler. If the power cord is damaged, replace it with a similar one.

When disconnecting the electric heater, use a two-pole switch, the gap between open contacts is from 3 mm. Also note that the pipes to which the water heater pipes will be connected have withstood temperatures in excess of 80 degrees Celsius and the maximum working pressure.

Precautionary measures

If you know that you will not be using the appliance for a while, simply drain all the water from it. To do this, turn off the power to the device, close the cold water supply valve at the water heater, and open the hot water tap on the mixer. Open the tee drain valve. A magnesium anode that wears out over time should be replaced with a similar one. The first start-up of the device should be carried out strictly according to the instructions.

Prevention

With frequent use of the boiler, the first technical inspection should be carried out in six months or a year. Every 3 months it is recommended to drain the contents of the tank in order to remove sediment, which prevents heat transfer and reduces the efficiency of the heating element. It is also recommended to replace the magnesium anode after a year of operation of the device. Never ignore the error codes that appear. You can see in detail what each of them means in the instruction manual.

The history of the Italian company Ariston dates back to 1930. Then the product range was limited only to scales, but today it includes multifunctional household and professional appliances. Among the favorites is a reliable and durable Ariston water heater. It differs from competitive technology in a key ratio of qualities for consumers - price-quality.

Long history

In 1930, thanks to the quick-witted Aristide Merloni, a new brand appeared on the household appliance market - Ariston. The family business specialized in the production of scales. A little later, the assortment was replenished with electric heaters, cylinders for liquefied gas. Flowing and storage water heaters in the catalog on the official website appeared relatively recently. Further, the business was transferred to the sons of the founder - Vittorio, Antonio and Francesco. As a result of the division of the company, there were three main divisions:

• Ardo;
• Merloni Elettrodomestici;
• termosanitary.

All companies specialize in the production of equipment under the brand name Ariston. Until today, one of the divisions has been intensively acquiring shares in other enterprises, expanding its composition, assortment and approaching the main market competitors - Bosch, Siemens, etc. The repurchased brands include the well-known Indesit and Scholtes, as well as 50% of GDA, which produced household equipment Hotpoint.

Today, factories in different countries are engaged in the production of instantaneous and storage water heaters Ariston, as well as other equipment:

• Poland;
• Russia;
• Turkey;
• Italy;
• France;
• Portugal.

In terms of turnover, this holding ranks third in the world ranking.

Rating of the best models of Ariston water heaters

The official website of the company is full of various Ariston water heaters. They differ in price, installation method, technical specifications, principle of operation and design. Based on these criteria, a the lineup the most successful variations, both in the opinion of specialists from the service center and users.

Ariston ABS BLU EVO RS 30

The Ariston 30 heater has funded system heating. His small size 44.7x44.7x41 cm allow installation in a vertical position under the washbasin. The storage water heater of 30 liters is powered by a voltage of 220 volts, while consuming a power of 1.5 kW.

Ariston ABS BLU EVO RS 30

Thanks to the latter indicator, the device is able to heat water up to a temperature of 80 ° C, and it takes only 70 minutes to get the optimal temperature of 45 ° C. As an additional function, there is a thermostat and an overheating protection function. The price of Ariston 30 liters is 5800 rubles.

Ariston ABS VLS EVO QH 80 D

The Ariston 80 l water heater has a storage heating system with an electric tubular heater. It can be installed both vertically and horizontally. Boiler Ariston consumes power of 2.5 kW from a power source with a voltage of 220 V.

Ariston ABS VLS EVO QH 80 D

The device is capable of heating water up to a temperature of 80°C. EVO Ariston 80 liters is equipped with a stainless steel coated tank. Separately, it should be noted the protection system against overheating and starting without water. Equipment dimensions 50.6x106.6x27.5 cm, weight - 27 kg. There is an Ariston water heater of 80 liters - 16,000 rubles.

VIDEO: Overview works by Ariston ABS VLS EVO QH 80 D

Ariston ABS Andris Lux 15 UR

The Ariston water heater for 15 liters has a boiler with a silver coating on the inside. The electric device has a rated power of 1.2 kW, thanks to which the heating element is able to heat water up to a temperature of 75 ° C.

ABS Andris Lux 15UR

The device is installed on 15 liters under the sink, due to this you can save a lot of usable space. The cost of a storage electric water heater is 7,000 rubles.

VIDEO: Overview of ABS Andris Lux 15 UR

Ariston 50 ABS VLS Evo Inox

The water heater for 50 liters has an attractive design and small dimensions of 50.6x27.5x77.6 cm. The design includes an immersion heating element, which has a power of 2.5 kW. Ariston for 50 liters can heat water up to a temperature of 80 ° C.

Ariston 50 ABS VLS Evo Inox

The device operates from a power supply with a voltage of 230 volts. The Ariston electric water heater is equipped with a display, safety valve. The price of the apparatus for 50 liters is 21,500 rubles.

VIDEO: Ariston 50 ABS VLS Evo Inox review

Spacious storage water heater Ariston 100 l is installed on the surface of the wall. Its dimensions are 125.1x50.6x27.5 cm. The design includes an immersion tubular heater. The device is equipped with an electronic display that shows all operating modes and other necessary information. Inner part the tank is covered special material Ag+, and an enameled heating element is also built into it.

Ariston 100 liters ABS VLS EVO

The 100 l storage water heater has a double boiler system, due to which the water warms up much faster. Already 29 minutes after switching on, you can take hot shower. The intelligent system of the device automatically remembers all heating cycles, so the equipment will prepare water by the time it is used most often. The price of a model for 100 liters is 19,900 rubles.

VIDEO: Overview of Ariston 100 liters ABS VLS EVO

Ariston ABS VLS Inox PW50 (cumulative)

This is a horizontal 50-litre machine, which has a flat rectangular shape, thanks to which it fits perfectly into small-sized rooms. In addition, it has the ability to work with several water intake points, which makes it possible to create autonomous system heating water for all faucets installed in the house.

Ariston ABS VLS Inox PW50

The power of the equipment is 2.5 kW, it has 2 heating elements. As a safety feature, Ariston 50 liters uses a device shutdown system with an empty tank and overheating. The nominal liquid heating temperature is 80°C, and the outlet pressure is 0.2-8 Atm. In online stores, such equipment is sold at a cost of 19,000 rubles.

VIDEO: Ariston ABS VLS Inox PW50 work overview

Problems and malfunctions of Ariston water heaters

Ariston equipment is rightly considered reliable, able to work for many years without causing inconvenience. However, regular maintenance and preventive inspection of the equipment is necessary.

Among the main faults are:

• failure of the electronics - only the sensor, heater or switch may break, or maybe all at once;
• during operation, the machine may knock out, which means that the equipment lacks “cash” voltage - for correct operation, you will have to turn off all powerful electrical appliances in the house for the duration of the wash;
• the problem with the ignition may be poor-quality wiring.

All problems are solvable, but on condition that repairs and maintenance are carried out by service specialists.

VIDEO: Why the boiler does not turn on and does not heat