The water in the taps leaves much to be desired, so lime deposits remain on the walls of all devices that come into contact with it.

Even expensive water filters will not be able to prevent plaque. Sooner or later, it will appear on the surfaces of the appliance and the question will arise how to clean the kettle from scale.

Folk methods

Limescale can be removed quickly using special chemicals. But since they are not safe for health, many prefer folk methods that have been tested by time.

Vinegar

Vinegar is not suitable for removing lime deposits in an electric kettle. This tool is too aggressive and manufacturers do not recommend using it for such equipment.

You can clean the electric kettle with vinegar only as a last resort, when a large layer of deposits has accumulated.

During the procedure in the kitchen will be felt. Therefore, manipulation should be carried out in a room with good ventilation. Open all windows and vents.

When working with vinegar, wear a protective mask so as not to breathe in harmful fumes.

How to clean the kettle from scale:

1. For metal devices, the following solution is prepared: 150 ml of 9% table acid is mixed with 1 tbsp. l. essences. ⅔ of water from the total volume is poured into the container, then the prepared composition is added. The mixture is heated and boiled for half an hour. After turning off the stove, leave the kettle for 5 minutes so that the water cools down a bit and repeat the procedure again. This must be done up to 3 times. With a strong limescale, the solution is left overnight. After that, you need to be good.
2. How to descale an electric kettle: Plastic-cased devices can be damaged if pure acid is used, so preparing the solution is a little different. Water is poured into the device to be cleaned with 5 tbsp. l. citric acid and acetic acid. The device is turned on, left to boil, then turned off. After 15 minutes, the process can be repeated. The process is repeated 3-4 times until the entire plaque is removed. Then washed with detergent.

Descaling the kettle with vinegar is quick and easy. Only such a remedy leaves behind bad smell even after using detergent.

Will save from the stink of boiling clean water which is carried out at least 3 times.

Lemon acid

Cleaning the kettle from scale is gentle for him and safe for humans. Citric acid is an excellent remedy for getting rid of plaque from any thermal elements.

The advantage of this product is the absence of an unpleasant odor, which is good if there are small children in the house.

How to clean the kettle with citric acid from scale:

1. For conventional appliances: take 2 packs of product, fill the appliance with water, but not completely. Add citric acid to the liquid and boil. The solution should cool down, leave it for 10 minutes. Then cleanse and remove plaque. The procedure can be repeated if the plaque has lagged behind the walls unevenly.
2. How to clean the kettle from scale with citric acid, if it is electric: a solution of 1–2 tsp is poured into the bowl. funds and 1 liter of water. After the liquid boils, it is drained and another one is collected. Need to boil clean water repeatedly.
3. If the deposits are small, you can clean the kettle from scale with citric acid even easier. It is dissolved in warm water, pour into the device and leave for 6 hours. After that, you need to wipe off the plaque with a sponge.

Descaling the kettle at home is easy and cheap. You can buy the product at any grocery store.

Sodium bicarbonate

Not only Coca-Cola is suitable, but also Fanta, Sprite, Lemonade, Schweppes.

How to remove scale in an electric kettle:

1. First you need to release the gas from the drink.
2. Pour 500 ml of Sprite into a container, close and let it boil.
3. After boiling, the device is turned off and the liquid is allowed to cool.
4. Wash off the remnants of plaque with a soft sponge, rinse kitchen appliance several times with clean water.

Coca-Cola and other carbonated drinks contain phosphoric acid. Thanks to her, it turns out to remove lime deposits.

This method is ancient - it was successfully used by our great-grandmothers. The method is suitable for all types of devices and is available to everyone.

The only drawback is that it will not cope with chronic growths.

How to descale an enamel kettle:

1. Water is poured into the device and washed apple or potato peels are placed.
2. The liquid is brought to a boil and left for 1.5 hours.
3. Then they walk along the walls with a sponge.

You can clean the electric kettle from scale using this method if you carry out the procedure several times a week.

If the appliance has not been washed for a long time, do not waste your time. Apple peel and potato peels will not help in this case.

Brine

Plaque removal is possible with cucumber or tomato brine. This is an effective folk way.

How to remove scale in an electric kettle:

1. Pour the brine into the appliance.
2. Bring to a boil.
3. Cool, pour out the brine and wash thoroughly from plaque.

This tool is not standalone. Thanks to the vinegar and salt in its composition, the purification process takes place.

Oxalic acid

Of all cleansers folk remedies oxalic acid is considered the most aggressive. It removes heavy limescale deposits.

How to remove scale from the kettle?

Advice of hostesses - algorithm of actions:

1. Not a large number of I pour the funds into the device and fill it with water.
2. The solution must be boiled and left for 5 minutes.
3. I remove the remains of the product and clean it with a soft sponge.

Oxalic acid good remedy and many housewives recommend using it. Fresh sorrel can also be used to descale, only it contains a little acid, several manipulations may be required.

Household chemicals

Range household chemicals great. Products on the shelves of stores effectively remove scale in the kettle.

Before using any products, wear gloves and a protective mask.

Antinakipin and Major Domus can be used as cleaning agents. These decalcifying chemical products are effective on all types of soiling.

How to wash limescale:

1. Antinakipin. First, water is poured into the dishes to be processed, then the contents of the bag are poured at the rate of 100 g per 2–2.5 liters of water. The solution is brought to a boil and boiled for 20 minutes. After turning off, the liquid is left for 2-3 hours so that Antinakipin works better. To clean the kettle, take a sponge and remove the remnants of plaque.
2. Major Domus. The product is poured into a container, left for 20 minutes. You don't need to boil. After that, the device is washed with plenty of water. If necessary, the procedure can be repeated.
3. Cillit another good one industrial tool, capable of quickly removing plaque from the surfaces of the inner walls of coffee makers, kettles. It is necessary to fill the container with clean water, dissolve Cillit in water in a ratio of 100 ml for every 500 ml of water. The agent is left for half an hour. After that, the container must be rinsed. Cillit should be used no more than once a month.

Household chemicals can cause serious irritation of the mucous membranes. When using such tools, you must wear glasses, or do not touch your eyes with your hands during manipulation.

Removal of limescale must be carried out in a timely manner so as not to resort to the use of household chemicals.

Due to the large amount of accumulated plaque, the electrical appliance is not only a source of some diseases, but the functionality of the device suffers because of it. Before changing the device to a new device, it is worth trying one of the folk methods cleaning.

Instruction

The easiest way is to buy any "anti-scale" in the store and clean it following the instructions. Such a tool, as a rule, costs. But, if you want to protect your health from accidental ingestion of chemicals, it is better to use natural remedies.

Boil the resulting solution and leave for at least two hours, and if possible, overnight.

After pouring out the solution, rinse the kettle thoroughly with running water and boil again to remove any remaining vinegar and scale.

In addition to acetic acid, citric acid can be used to combat scale - 1 tablespoon per 1.5-2 liters of water. Pour acid into the kettle, pour hot water and leave for 15-20 minutes. It is not necessary to boil the solution. If the raid was not very strong, then after the specified time the kettle will shine like new.

In the absence of citric acid and vinegar in the house, do not despair. It may be unexpected, but in the past, grandmothers got rid of with the help of an ordinary!

Take clean potato peels, cover the bottom of the kettle with them and add 1.5-2 liters of cold water.

Drain the cooled water and rinse the kettle well with tap water.

If you are still unhappy with the result, try another very extravagant remedy.

Use a special descaling pencil. Heat the iron to 100°C, apply the product evenly on the soleplate and leave it in this state for several minutes. Then delete scale cotton fabric. Pour into clean water and clean the holes with steam.

Delete scale with an iron table vinegar. Prepare a solution of 1 cup of water and 1 tablespoon of vinegar. Pour the liquid into the iron and turn on the steam function.

Descale the washing machine with a special tool, such as Antiscale. It can be bought at a hardware store. Before use, read the instructions or consult the seller.

Pour the product into the washing drum, set the mode at a temperature of 60-90 ° C. To prevent the formation of scale, carry out a similar procedure regularly - once a month. If your city or area has poor water quality, do preventive maintenance every.

Tip 4: How to descale the kettle with improvised means

Scale in the water appears due to the content in it of a large amount of salt and impurities that settle on the bottom, walls and heating element of the electric kettle. If not on time, then this may affect a quick breakdown, or the process of heating water will be longer. In this case, scale affects the body negatively, destroying the kidneys and the genitourinary system.

The easiest way to remove scale is with citric acid. To clean the scale, you need to buy one bag of food-grade citric acid. Pour the acid into the kettle. Dial into it cold water and leave for a few hours. Then pour everything out of the kettle, pour fresh water and boil several times.

If citric acid did not cope with scale, then pour 100 g of 9% vinegar into a kettle with water, then boil this mixture, pour it out and rinse the kettle thoroughly.

Fanta, Sprite or Cola soda is suitable for descaling. It is necessary to remove gases from them, fill the kettle by 1/2 and boil.

Potato peels are also suitable along with apple peels. They should be washed, put in a kettle of water and boiled several times.

If the kettle has a high scale content, then you can do the following procedure: Pour a full kettle of water, add 1 tbsp of soda and boil for 30 minutes. Change the water, add 1 tablespoon of citric acid and also boil for 30 minutes. Change the water, add 150 g of vinegar, boil. With this method, the scale will become soft and must be removed with a sponge.

Related videos

Tip 5: How to descale a stainless steel kettle

Lime deposits in water not only make it hard - when boiling, substances settle inside the kettle, forming scale on the walls. Depending on the material of the kettle, scale will form on it less often or more often.

In stainless steel, scale forms somewhat more slowly. However, it cannot be completely avoided. Scale slows down the process of boiling water, and if it does, then it takes a lot of electricity. Deposits can harm not only the kettle, but also the person who drinks the water boiled in it. The filters installed on the spout are of little help in solving the problem.

Scale prevention

Most The best way to combat scale - to prevent its formation at all. The rules to follow for this are quite simple. For boiling it is necessary to use soft and clean water, passed through a filter or settled. It is necessary to boil a portion of water once. Water that has already boiled should not be heated - it is better to replace it with fresh water. Before each use, it is advisable to rinse the teapot well from the inside, rinse from the white flakes that form, the walls of the teapot should be cleaned of plaque more often.

Means with which you can remove scale

In hardware stores you can buy quite effective means to deal with scale, like Silita, Antinakipin. Their use is almost the same: basically, the funds must be poured into a kettle, pour water and boil. After about fifteen minutes, the kettle should be rinsed with clean water.

If a reddish scale forms during boiling, citric acid will help. But for enameled it is better not to use it. Prepare a solution of a liter of water and a teaspoon of acid, boil it. Leave for 10 minutes and boil again. If the raid still remains, after the second boiling it is not necessary to drain the water - it is left in for another couple of hours.

You can clean your stainless steel kettle with a mixture of vinegar and baking soda. Suitable for those who can easily tolerate the smell of vinegar. Mix soda with water until gruel and rub into the walls of the kettle. After that, dampen a cloth with strong vinegar, wipe over the slurry. Baking soda and vinegar react and can be done very easily.

Scale can be removed with soda water - Coca-Cola or Sprite. The liquid must be poured into the kettle, boiled and left for about 10 minutes. Then drain everything, and rinse the kettle. For teapot white color it is better to use a sprite - so that the dye does not spoil the whiteness.

Whatever tool is chosen - soda, sparkling water or specialized household chemicals - descaling should be done regularly. Then the cleansing is much easier, and the scale will form much less.

Tap water, which is poured into the kettle, contains a large amount of different salts. They gradually settle on the inner surface and on the bottom of the kettle, resulting in scale formation. It must be removed regularly - there are a lot of funds for this, and you can choose any convenient method.

You will need

• - means of household chemicals for descaling;
• - vinegar;
• - baking soda;
• - lemon acid.

Instruction

Pour into the kettle special remedy for descaling. It can be Antinakipin, Antinakip or other household chemicals with a similar effect. They are very easy to use - you just need to fill them with water and boil. This method can be called the easiest, but at the same time it is far from the most useful. Cleaning products contain many chemicals, which, even after repeated rinsing, may partially remain in. If they enter the stomach, they are dangerous to the body.

Try to descale more in a safe way- using the usual . Boil water, add three tablespoons of soda to boiling water. After that, the water should cool down. After about half an hour, boil the kettle again. Pour boiling water, and fill the kettle with hot water with the addition of a couple of tablespoons of vinegar essence. Boil water again and cool the kettle. After carrying out these activities, the scale becomes loose, it is very easy to remove it with a regular dishwashing sponge. This method is good for running ones. No matter how thick the scale layer is, it begins to move away in thin plates.

Take citric acid - two sachets are enough for a standard three-liter kettle. Pour the powder into cold water and boil. Leave the water in the kettle for about half an hour, then drain, pour fresh water and boil again. The acid will easily break down the scale. After that, the kettle will need to be thoroughly rinsed so that there is no aftertaste left. This method is perfect for descaling both in simple and in. But here for metal teapots citric acid is contraindicated. In the process of dissolving scale, acid makes rough inner surface kettle, and new scale will form in it much faster. With a thick crust of scale, citric acid will not cope.

At the moment, the electric kettle has become a decoration of the kitchen and indispensable assistant however, a problem such as scaling may occur as a result of repeated use. If left untreated, lime scale can cause an unpleasant taste in water and damage the appliance. In order to remove scale in the electric kettle, you can use the following tips.

Plaque forms on the heating element of the kettle and its walls, which is ordinary salt that has settled on the surface. Before cleaning, you need to figure out what is the cause of limescale. Sometimes it's about the quality of water: then it is necessary to replace it with a better one.

In order to remove scale, you will need the simplest products that most housewives have in the kitchen.

1. You will need 2 tablespoons of vinegar and 50 g of citric acid: pour vinegar into the kettle and then pour lemon, boil the kettle and leave it with this mixture for 60 minutes. After the specified time, the plaque can be easily washed off with a sponge. If the first time there is a plaque, then you can repeat the procedure. Sometimes lemon is used instead of citric acid.

2. Baking soda is an excellent tool for cleaning the kettle. First, pour water into the kettle, then pour 1 tablespoon of edible salt there, boil the water and leave for 30 minutes, then pour water into the kettle again, add 0.5 teaspoon of citric acid and put on fire again. After the water has cooled, you can start washing the kettle with a kitchen sponge.

3. Vinegar also helps to clean the kettle: pour a third of vinegar and two parts of water into the kettle, then boil the water and leave it to cool. Scale in the kettle under the influence of acid will dissolve, then it can be easily washed off.

4. One of the most unconventional cleansing methods is the use of regular sparkling water. Pour water into a kettle, bring to a boil, and then drain. After this manipulation, the limescale should move away.

5. Keep in mind that there are a large number of household chemicals in stores for cleaning limescale. Sometimes such funds are quite expensive, and the result is not so effective, so you can use the methods.

Consider the following points:

1. After carrying out the cleaning procedure, the electric kettle must be rinsed, otherwise the substances that you used for cleaning may enter the body along with drinks.

2. Most the best remedy in the fight against scale - this is the daily care of your electric kettle.

Related videos

Scale appears due to impurities contained in poor-quality water. During boiling, they settle on the walls of the kettle and spoil the taste of hot drinks. Also, scale does not conduct heat well, so a dirty kettle will boil longer.

How to clean a kettle with vinegar

The method is suitable for very dirty teapots made of plastic, glass, stainless steel.

You will need:

• ½ liter of water;
• 1 cup 9% vinegar or 2 tablespoons 70% vinegar essence.

Heat water in a kettle, and then pour in vinegar or vinegar essence and leave the solution for an hour. During this time, the scale will soften. Rinse the kettle from the inside with a sponge, boil clean water again and drain it.

How to clean the kettle with lemon or citric acid

The method is suitable for electric kettles made of stainless steel, plastic or glass with a moderate layer.

Not suitable for enamel and aluminum kettles.

You will need:

• ½ liter of water;
• ¼ lemon or 2 tablespoons citric acid.

Heat water in a kettle and put a piece of lemon or citric acid into boiling water. Leave the scale to soak for 1-2 hours. Rinse the teapot with a sponge and rinse thoroughly. After the first boil, the water will need to be drained.

How to clean a kettle with baking soda

The method is suitable for any kettles.

You will need:

• ½ liter of water;
• 1 tablespoon of baking soda.

Stir the baking soda in a glass of water so that it dissolves completely. Pour the resulting liquid into the kettle, add the remaining water and boil it. Wait half an hour or an hour and heat the kettle again.

Now you can wash the kettle and boil clean water in it. True, after it will have to be poured.

How to clean a kettle with soda

The method is suitable for stainless steel kettles heated on a stove.

Not suitable for aluminum, enamel and electric kettles.

You will need a bottle of any lemonade. The most famous option is cola, but it is better to use a colorless drink (it is important that the composition contains citric acid).

Let an open bottle of lemonade sit for 2-3 hours to eliminate gas bubbles. Then it's simple: pour the drink into the kettle and bring to a boil. Then thoroughly wash and rinse everything.

How to peel a kettle

The method is suitable for enameled and metal teapots with a weak layer of scale.

Not suitable for electric kettles.

You will need:

• ½ liter of water;
• skin 2-3, apples or pears.

Rinse the cleaning from dirt and sand, put them in a kettle and fill with water. Boil the liquid and leave to infuse for one to two hours. A light layer of scale will come off on its own, rub stubborn dirt with a sponge for washing dishes. After rinsing, the kettle will shine like new.

If you have a particularly capacious kettle, and scale has accumulated on the walls, take more water than indicated in the recipes. The liquid must cover the contaminants completely.

How to keep the kettle clean for a long time

1. Pour soft water into the kettle. If you don't buy bottled, use a filter. Or at least stand your tap water for a few hours to allow the impurities to precipitate.
2. Boil water in the kettle no more than once. Better fill it fresh.
3. Rinse the inside of the kettle at least once a day. And ideally before each use.
4. For prevention, once a month, boil a filled kettle with one tablespoon of citric acid.

Look inside your favorite pot for boiling water for tea and you will see white streaks, deposits on the walls. Any electric kettle will accumulate a layer of lime over time if it is not regularly cleaned. This plaque contains hard deposits of minerals when hard water is used, which does not pass through the filter. "Crust" on the walls impairs the operation of heating devices, is harmful to health. After reading the material, you will learn how to remove salt from the inside of electric and other tea utensils using traditional folk remedies.

How to remove scale in a kettle

To clean it from mineral plaque, especially if this dish is used daily, it is imperative to systematically. The formation of deposits depends on the quality of the water used: if it is hard, then a layer of mineral plaque and lime will form on the walls much faster. How to wash the kettle from scale? There are various tried and tested home tricks to help remove these mineral deposits. Baking soda, vinegar, cola, citric acid, household products work to eliminate this problem.

How to clean a kettle with citric acid

How to remove scale in a kettle using citric acid? It cleans metal brewing, plastic, glass products. In order to clean, you will need to boil half a liter of water, adding 2 large tablespoons of citric acid there after boiling. Wait a couple of hours for the water to cool. Removal of the "crust" on the walls, cleaning will occur on their own. It rarely takes a little help with this solution to successfully fight plaque. After that, boil clean water again inside, drain it. Your tea will become tastier and your health will not suffer.

Descaler

How to clean the kettle from scale using specialized cleaning products from the household chemicals departments of stores and supermarkets? With their help, you can wash a product made of stainless steel or any other material. To find out if a cleanser is right for you, read the label carefully before buying. After purchasing the product, you only need to strictly follow the attached instructions. As a rule, you need to boil water, add powder, cool this solution, drain it and wash it well with clean water, boiling it a couple of times.

Vinegar

Try an effective, inexpensive way to descale your kettle with vinegar. It is aggressive, so the method is suitable for removing heavy mineral deposits. It is used for tea utensils made of glass, plastic, metal. To carry out the removal of plaque, you will need to pour half a liter of water, boil, add a glass of 9% vinegar, leave for an hour so that the process goes arbitrarily. Sometimes you need to walk along the walls with a sponge. An important condition is to thoroughly rinse the heating device from vinegar after the procedure, then boil it a couple of times with clean water.

soda

To clean an enameled kettle, aluminum utensils, soda will help - a folk remedy for scale, which is easy to find in retail and it costs a penny. This will require 500 ml of water and a tablespoon of soda ash. If the mixture does not cover all the limescale, then increase the amount of water with soda. Bring the resulting solution to a boil and cook it over low heat for half an hour. To enhance the effect, leave the water with soda to cool there for a couple of hours. If necessary, rub the excess with a sponge, rinse the dishes well and boil clean filtered water there.

How to descale a Coca-Cola kettle

Try in practice another extraordinary way to fight against mineral plaque, which will require a strong carbonated drink containing citric acid. This option is only suitable for electric heaters. How to clean the kettle from scale, just adding Coca-Cola? First of all, you need to release gases from the drink, leaving it alone with the lid ajar for an hour, pour it into a bowl and boil. Leave to cool for a while, if necessary, rub with a sponge or hard washcloth. Drain the liquid, rinse with clean water.

Video on how to get rid of scale in an electric kettle

The energetic and very nice presenter of the video will popularly talk about the simplest but most effective measures for cleaning electric cookware in order to forget about plaque for a long time. How to remove scale in an electric kettle? If you have such a heating device for making tea, then this video will help. After watching the video, you will understand which tool is suitable for your case. Spend just a couple of minutes of your personal time, but you will understand which is better - soda, vinegar or lemon?

In any water heater, from time to time we find a treasure of minerals, namely deposits of magnesium and potassium salts from hard water. And if we always try to prevent its occurrence in the dishwasher and washing machine, what can we say about scale in the kettle, which not only impairs its performance and leads to breakdowns, but also harms the health of the household.

We have collected 5 of the most effective and affordable ways to descale a kettle at home. In fact, the secret of all folk remedies is very simple:

• Scale in a kettle or electric kettle is afraid of organic and inorganic acids, so almost all methods of descaling at home are based on the use of acid-containing solutions.

Method 1. How to descale an electric kettle with vinegar

Manufacturers of electric kettles do not advise using vinegar to remove mineral deposits - after all, it is too aggressive. But sometimes you can't do without this powerful tool.

The method is suitable for: plastic, glass and metal teapots with a very large amount of old scale.

Ingredients: water - about 500 ml and vinegar 9% - a little less than 1 cup or vinegar essence 70% - 1-2 tbsp. spoons.

Recipe: pour water into the kettle and boil it, then pour acetic acid into boiling water and leave the scale to soak in the solution for 1 hour. If the scale has not gone away on its own, but only loosened, then it will need to be removed with a sponge. Remember to boil water in a clean kettle once or twice, and then rinse it well to wash off any remaining vinegar.

Method 2. How to descale an electric kettle with citric acid

The method is suitable for: cleaning electric kettles made of plastic, stainless steel and glass with light or moderate dirt.

Ingredients: water - about 500 ml and citric acid - 1-2 tbsp. spoons (depending on the degree of contamination). A quarter of a lemon can replace powdered acid.

Recipe: also pour water into the kettle and boil, then pour citric acid into boiling water or put a quarter of the lemon and wait until the water cools for about 1-2 hours (be careful - the acid that got into hot water, "hiss"). If the scale is not old, then it will come off on its own, otherwise you will need to make a little effort. Do not forget to boil water in a clean kettle, and then rinse it well.

Method 3. How to get rid of scale in a kettle of any kind using soda

enameled and aluminum cookware afraid of aggressive acids, so the first 2 ways to remove limescale are not suitable for them, but a regular soda solution can help you.

The method is suitable for: descaling both in ordinary enameled and aluminum kettles, and in any electric kettles.

Ingredients: baking soda, and preferably soda ash - 1 tbsp. spoon, water - about 500 ml (the main thing is that it covers the entire limescale).

Recipe 1: to remove scale from the walls of an enameled or aluminum kettle, you must first mix soda with water, then bring this solution to a boil, and then leave it to simmer over low heat for half an hour. At the end of the procedure, we wash off the remnants of soda, for which we boil clean water 1 time, drain it and rinse the kettle.

Recipe 2: To wash an electric kettle with baking soda, you need to boil water, make a soda solution, and then let it cool for 1-2 hours. A more gentle way is to pour soda into boiling water, and then leave the solution to cool completely - during this time, the mineral deposits will become softer, and it will be easier to wash them by hand.

Method 4. How to descale the kettle with Coca-Cola and Sprite

This method is not the most efficient and economical, but why not try for fun?

The method is suitable for: descaling in ordinary stainless steel kettles and for electric kettles, but for enameled and tin ones - with caution.

Ingredients: any carbonated drinks with citric acid in the composition are suitable - from Coca-Cola to Fanta. But it is better to take colorless drinks, for example, Sprite or Schweppes.

Recipe: First, we release gases from the drink, then pour 500 ml of liquid into the kettle and let it boil and then cool. The result of the experiment can be seen in this video.

Method 5. How to remove scale in a kettle using apple or potato peels

This product is suitable either for preventive care or if the limescale is still weak.

The method is suitable for: descaling ordinary enameled and metal kettles.

Ingredients: Apple, pear or potato peels.

Recipe: put apple, pear or washed potato peels in a kettle, pour water and bring to a boil. As soon as the water boils, leave the peel to cool for 1-2 hours, and then wash the softened plaque with a sponge.