Ariston electric water heater instruction manual. General information on Ariston water heaters

An analysis of sales of the domestic market for water heating equipment shows that the undisputed leader here is the products of the Italian company Ariston. Consistently high quality, reliability, ergonomic design - that's what attracts consumers to the products of this company. Among the many models, the most popular are Ariston 100 l water heaters, since they are able to satisfy the daily need for hot water for a family of 3-4 people. It consists of a body and a tank covered with insulating material, as well as a heating element and control devices (thermostat, control unit).

The manufacturer, among others, manufactures installations that have a volume of 100 liters. Mostly electrical devices accumulative type, which are used to heat water in apartments, private houses and other premises connected to the mains. They are presented in the following series:

1. Ariston ABS Velis (QH, INOX QH, POWER, INOX POWER, PREMIUM).

The abbreviation ABS means that all models are equipped with the Absolute Bodyguard System - a residual current device. In the event of power outages, water leaks or problems with the pressure valve, the system blocks the operation of the device, making it absolutely safe. The main difference between Velis 100 V and other series of units is that they are equipped with 2 internal independent tanks, in which it is installed according to the heating element.

This allows you to get water heated to 45 ° C already 53 minutes after switching on. Both tanks are internally treated with a layer of AG+ (plating with silver content), which helps to protect the body from corrosion. The wall-mounted storage electric water heater Ariston Velis can be mounted on the wall in any position: vertical or horizontal. A digital display with programming function is installed on the front panel of the boilers.

2. Overview electric water heater Ariston ABS PRO R 100 V indicates that the unit is equipped with a tank made of cold rolled steel. Its surface is coated on the outside with a layer of finely dispersed enamel, which provides protection against leakage and corrosion. The Ariston ABS PRO-R 100 electric water heater is equipped with an on / off indicator, a reliable mechanical thermostat and a heating scale displayed on the outer panel of the device. In addition, it has a special, magnesium anode, which protects the heating element from premature wear.

In the production of a metal tank of a 100 l Ariston ABS PRO ECO 100 V storage water heater, a special welding technology (microplazmatig) is used, due to which high strength and durability of the seams are achieved, and the boiler is able to withstand pressure drops up to 15 atmospheres. Silver-derived ECO coating neutralizes harmful chemical elements. The unit is equipped with an electric thermometer that allows you to monitor the operation of the boiler in real time, ensuring constant temperature control.

1. Ariston ABS Blu.

The devices of this series are represented by the R and ECO model lines. Description vertical water heater Ariston Blu R100V says that this modification is equipped with a simple mechanical thermostat. storage capacity the outside is covered with a protective layer of polyurethane, which contributes to the fastest possible heating. The walls of the tank are covered with a protective layer of Ag+ from the inside. Another model - BLU ECO POWER 100V, is equipped with an electronic thermostat and a digital display. It is intended for the accelerated heating of water.

The series includes compact boilers TI TRONIC, TI TECH and TI SHAPE. Ariston TI TRONIC is a high-quality water heater equipped with a mechanical device for temperature control. The inside of the container is treated with Titanium + technology, which provides it with protection against rust formation. The Ariston TI TECH QB 100V compact water heater device is equipped with a simple thermostat, but it has more power and heats the water faster to the desired temperature.

3. Ariston Perla.

This is a type of heating devices that combine 2 heating methods. For instance, specifications combined water heater Ariston PERLA 100 VRDT / 5 are such that, thanks to the heat exchanger built into the tank, heating season it can function as an indirect type heater. Then a 1.5 kW heater makes it possible to use it as an electric boiler, for this it is only necessary to turn off the tap connecting the installation to the heating system.

Models of this series also belong to the combined type and are equipped with two types of heaters: a heat exchanger and a heating element. In addition to the main thermostat, the SG R 100 LTDTS has an additional one, which makes the work completely safe.

In addition to the above electric heaters, Ariston also produces units with a tank volume of 100 liters, powered by another source of energy - gas. but the lineup of such installations is limited to SGA products. Gas installations have natural draft and an open combustion chamber, which makes it possible to receive heated water regardless of the pressure in the gas and water supply system. In addition, they are equipped with a piezo ignition device with a built-in thermocouple that controls the flame. Modification of the wall-mounted boiler SUPER SGA is used for domestic and industrial needs.

Technical characteristics of water heaters with a tank of 100 liters

Series	Model	Indicators
		power, kWt	Voltage, V	Working temperature, °C	Pressure, bar	Water heating time up to 45 °C, min	Dimensions, mm	Weight, kg
Velis	QH,INOX QH	1,5+1	230	80	8	first tank - 53, second - 139	1275x490x270	30
	POWER, INOX POWER	1,5+1		80		First tank - 91, second - 139
Pro	R	1,5		75		206	913x450x480	26
	ECO	1,5		80		232	1338x450x470	26
blu	R	1,5		75		232	913x450x480	26
	ECO POWER	2,5		80		130	1338x450x470	29
TI	TI TRONIC	1,5		80		232	913x450x480	26
	TI TECH QB	2,0		75		170	963x493x499	34
PERLA	100 VRTD/5	1,5		80		232	913x450x480	25
SG	SG-R100L/RTDTS	1,8		80	6	175	904x450x470	35
SGA	SUPER SGA	4,4	—	45	8	71	950x495x510	35

Advantages and disadvantages

TO positive qualities Ariston boilers include:

• Rapid heating of the required volume of water.
• Processing of tanks using AG+ and Titanium+ technology.
• ABS system, which protects installations from breakdowns associated with power surges, leakage, and so on.
• Simple, reliable mechanical and electronic thermostats that allow you to achieve the most accurate control with an error of no more than 1 °C.
• Possibility of use at low pressure in the water supply system.
• The ECO function provides water purification from harmful chemical elements.
• With all the technical innovations used in the manufacture, the price remains affordable for any category of consumers.
• Warranty period from 5 to 10 years.

Judging by the reviews, the water heater is not without drawbacks:

• The load on the power grid increases by an average of 1-1.5 kW.
• When the power is turned off, such equipment will not work.
• The kit does not include brackets for wall mounting, flexible hoses for inlets, and a condensate drain pipe.

How to install an Ariston water heater

Electric storage boiler Ariston According to the instructions, it should be installed in dry, warm, well-ventilated areas. This process takes about 2 hours and consists of the following steps:

1. Using a perforator, holes are drilled in the wall for anchors, on which the water heater is hung.

2. With flexible hoses, it connects to water pipe. As a rule, the cold water inlet is marked in blue. It has a pressure relief valve. The red outlet is connected to the hot tap. Tow is wound on all joints.

3. Taps are opened and all connections are checked for leakage.

4. Using the connector, the device is connected to the mains. The contact on the water heater terminal, marked with the letter L, means "phase", with the letter N - "zero", yellow grounding is marked.

In the event of problems during operation, it is better to entrust the repair of the Ariston boiler to a specialist by contacting an authorized service center.

Such offices are open in all major cities Russia. Self repair can lead to damage to expensive components and removal from warranty service.

Price

Average prices in rubles in Moscow are different and depend on the series and model of the boiler. The cheapest TI Shape 100 V installation costs 4,800 - 5,660. Moreover, it is worth noting that the price of an Ariston TI Shape 15 UR water heater, equipped with a much smaller tank (only 15 liters), is not much less - 4,100 - 4,500.

• Model ABS Blu R 100 V will cost 5,900 - 7,000.
• You can buy Ariston ABS PRO ECO 100 V for 7,100 - 8,600, ABS Pro-R 100V is somewhat cheaper - 5,800 - 8,380.
• The cost of a 100-liter quick heating water heater Ariston Velis is 12,700 - 14,910.
• Settings combined type Perla 100 VRTD / 5 will cost an average of 9,440 to 10,400.
• The most expensive are gas-powered units SGA-17,100 - 1,9,700.

The firm "Ariston" specializes in the production of water heating equipment. Water heater "Ariston" 80 liters (instruction attached to the device), as well as other models of devices are widely known to the inhabitants of our country. Each new model has more stylish design and produced with the latest technology.

Figure 1. Ariston water heater for 80 liters

Characteristics of water heaters

All models of water heaters of the company have a very long service life. This effect is achieved by coating the inner walls of the device. modern materials which protect the boiler from rust. Cold and hot water do not mix inside, so it is possible to constantly maintain the temperature of the liquid inside the unit. Built-in temperature sensors are designed to protect Ariston from overheating. At the moment of a sharp change in the mains voltage, a protective device is activated and disconnects the boiler from the network. A special thermal insulation layer that keeps the water hot saves electricity or gas.

Some models of heaters have protection against bacteria. Water in such devices is always clean. Sometimes it happens that there is no water in the plumbing system. In this case, the device cannot turn on. Again, a special protection system will not allow him to do this. Almost all models of the company, including Ariston 80, 100, 30 liters, are equipped with the functions listed above. Main differences different models consists only in the external design of the devices. The body can be flat, round, horizontal, vertical. Any of them fits perfectly into the interior of the room (Fig. No. 1). Internally, their device is exactly the same (Fig. No. 2):

• internal boiler;
• thermal insulation layer;
• branch pipe for water inlet and outlet;
• magnesium anode (Fig. No. 3);
• thermostatic thermostat.

Figure 2. The device of the Ariston water heater for 80 liters.

A boiler is a tank for cold water. Outside, it is closed by an outer casing. The water entering the tank is heated by a built-in heating element. Sometimes there are 2 heating elements. This is if an electric water heater. Between the boiler and the outer casing there is a layer of thermal insulation. In general, the design resembles a thermos device. The water in it retains its temperature for a long time. It comes out through the outlet tube. Ariston 80 also has a magnesium anode. It is installed to prevent deposits of mineral salts on the inner walls of the tank. It should be changed as needed. You can see this when cleaning the heating elements (Fig. No. 4).

When the water is heated to the set temperature, the thermostat disconnects the device from the network. The operation of the unit is monitored using an indicator light. The built-in thermometer allows you to monitor changes in water temperature. This is how the Ariston 80, 50 liter, 100 liter and other models are arranged. Their operating instructions are the same for any model. Each instrument is supplied with an instruction manual. It must be carefully studied, then the device will work for many years.

Figure 3. Magnesium anode.

Purpose of water heaters

Installation of a boiler in the house is carried out to provide housing hot water. The heater can be selected in 100 liters, 80 or smaller sizes. Everything Ariston models have the same internal structure, therefore, the connection diagram of the water heater is used the same for this series of devices. It is better to invite a specialist to install the device. If you decide to do it yourself, the work should be done according to the plan:

• inspect the device from the outside;
• prepare fasteners;
• check grounding;
• place the outlet correctly.

Figure 4. Cleaning the heating element of the Ariston water heater.

When inspecting the device, it is necessary to check the safety valve well. It should not have visible flaws. If they are found, the valve must be replaced. As fasteners, it is recommended to use plastic dowels and self-tapping screws for them. You need to connect a heater for 100 liters or any other to a separate power line. The outlet must be located in a dry place. The use of extension cords is prohibited.

Properly installed storage boilers run immediately after they are connected to the network. This is indicated by the illuminated indicators. The temperature of the water inside the device is also shown by thermometers.

Conclusion on the topic

There are many systems for providing hot water to private houses and country houses.

The most famous high quality devices are produced by Ariston.

There are many models, but they all have the same internal structure. Instructions for use of these devices is also the same for all brands. Storage devices for heating water differ only in external outlines. All characteristics of different models are also the same. Only the 80 liter model can still use the antibacterial function. To activate it, you just need to press the "power" button and hold it in this position for 5 seconds. The water temperature can be set between 30-75 °C.

Each time you turn it on, you need to control the water level in the boiler. When turning off the boiler for a long time, you need to drain all the water from it. Each device comes with a 1 to 2 year warranty. Repairs are made in almost every city with a warranty card.

Models:

Ariston SHT30H Ariston SHT 50 H Ariston SHT 80 H Ariston SHT 100 H Ariston SHT 30 V Ariston SHT 50 V Ariston SHT 80 V Ariston SHT 100 V Ariston SHT-EL 30 H Ariston SHT-EL 50 H Ariston SHT-EL 80 H Ariston SHT -EL 100 H Ariston SHT-EL 30 V Ariston SHT-EL 50 V Ariston SHT-EL 80 V Ariston SHT-EL 100 V

1. Initial information by electric water heater

1.2 The device and the names of the main parts

2. Specifications

2.1 Wiring diagram

3. General Warnings

4.Installation instructions

4.1.3 Installation of vertical water heaters

4.2 Water connection

6.1 SHT electronic model

6.2 Mechanical model SHT

1. Basic information about the electric water heater

1.1 Scope and characteristics

Electric storage water heater designed to provide hot water. Water heater series Ariston Shuttle, one of the essential accessories of modern life, is characterized by the following features:

1) The inner tank, made of high quality corrosion-resistant (stainless) steel, guarantees durability, corrosion and impact resistance;

2) high efficiency heating element with reliable insulation of the heating element;

3) protection against overheating and high pressure;

4) Easy to use intelligent control system.

1.2. The device and the names of the main parts

2. Specifications

2.1 Main specifications

Model	Volume, l	Voltage, V	Current strength, A	Power, W	Current frequency, Hz	Maximum pressure, bar	Water heater dimensions (LxHxB), mm	Packing dimensions, mm
SHT30H SHT30V SHT-EL30H SHT-EL30V	30	220	11.4	2500	50	0.6	603x380x270	670x470x352
SHT50H SHT50V SHT-EL50H SHT-EL50V	50	220	11.4	2500	50	0.6	898x380x270	965x470x352
SHT80H SHT80V SHT-EL80H SHT-EL80V	80	220	11.4	2500	50	0.6	985x450x310	1040x540x392
SHT100H SHT100V SHT-EL100H SHT-EL100V	100	220	11.4	2500	50	0.6	910x540x360	980x620x445

2.1 Wiring diagram

Mechanical Model SHT

3. General Warnings

Local codes and regulations may restrict the installation of electric water heaters in bathrooms. Merloni TermoSanitari cannot be held responsible for damage caused by incorrect installation by the user or by failure to follow the instructions in this manual. Installation must be carried out by qualified personnel. In particular, attention should be paid to the following points.

Electrical wiring must comply with the Electrical Installation Rules (PUE).

The safety valve supplied with the device must be in good condition and undamaged and must not be adjusted or replaced with a similar valve.

The heater must be installed by qualified personnel. The screws must be properly screwed into the plastic dowels.

Check that the mains voltage matches the specifications on the rating plate.

Check the correctness of the earthing done, in accordance with the current rules and regulations. The power outlet for the water heater must have a grounding contact and be properly grounded. Ground and neutral wires must be different and easily identifiable Attention: if the water heater is not grounded, then in the event of a short circuit, the RCD (residual current device) supplied with the kit may not work. This is dangerous!

Do not use any

The electric water heater must be powered from a separate electrical line from the electrical distribution board. Do not connect additional electrical devices to this line.

The power socket of the heater must be located in a dry place away from sources of splashing water.

An electric water heater uses a special power cord. If damaged, it must be replaced with a special power cord by a qualified technician.

To disconnect the heater from the mains, use a two-pole switch with a gap between open contacts of at least 3 mm.

4.Installation instructions

4.1 Installing the water heater on the wall

4.1.1 Installation position and wall requirements

The wall must support twice the weight of the heater filled with water. To reduce heat loss, the water heater should be installed as close as possible to the point of use of water. It is recommended to leave a free space of at least 50 cm around the water heater for maintenance.

Attention! The water heater is designed for indoor installation. If in winter time If you plan to use it, drain the water from it as it may freeze and damage it.

4.1.2 Installation of horizontal water heaters

You are taking optimal position on the wall for mounting the water heater. Be guided by the distance between the brackets C, indicated in the attached table.

Drill 4 holes for the strikers that are attached to the wall. Hole diameter ∅16 mm, depth 80mm.
striker

Insert plastic dowels into the holes. Next, using the screws inserted into the dowels, fix the strikers to the wall. Attention! When the head of the screw firmly presses the panel with hooks to the wall, stop screwing in so as not to damage the planks. Slowly keep lowering the water heater until it hangs on the wall; check the reliability of its fastening on the wall. When doing this, keep in mind the specified distance between the installation points of the slats.

4.1.2 Installation of horizontal water heaters

Choose the optimal position on the wall for mounting the water heater. Be guided by the distance between the brackets C, indicated in the attached table. Drill 2 holes for the strikers that are attached to the wall. Hole diameter W16mm, depth 80mm. For water heaters of 80 and 100 liters, 2 additional holes must be drilled. Insert plastic dowels into the holes. Next, using the screws inserted into the dowels, fix the strikers to the wall.
Attention! When the head of the screw firmly presses the panel with hooks to the wall, stop screwing in so as not to damage the planks.
Slowly keep lowering the water heater until it hangs on the wall; check the reliability of its fastening on the wall. When doing this, keep in mind the specified distance between the installation points of the slats.

4.2 Water connection

Screw the safety valve (A), which is supplied with the water heater, into the water heater inlet marked in blue (see fig. 7).
Connect the cold water line (B) to the bottom fitting safety valve.
Connect the drain pipe (C) to the relief valve drain. The free end of the drain pipe must be open to the atmosphere. Drain pipe must be slanted downwards and must not be pointed at the user.
Connect line hot water(D) to the outlet of the water heater marked in red.
The inlet and outlet pipes must be designed for a water pressure of about 0.6 MPa and a temperature of 95 °C.
To prevent damage to the safety valve, do not screw it too tightly into the water heater.

If the pressure in the water supply network is close to the set pressure of the safety valve, install a pressure reducer on the water supply line away from the water heater.
If a tap is installed in the cold water supply line, it must be constantly open.
During normal operation of the water heater, during heating, water may drip from the drain pipe of the safety valve, which means that the pressure is released from the device.

5. Actions after installing the water heater

Open the faucet in the cold water supply line, then open the hot water faucet on the faucet and wait until the outlet water flow is equal to the inlet water flow. This means that the water heater is filled with water. Close the mixer valve and leave the valve in the supply line open.
Attention! Before turning on the water heater, make sure that the tank is filled with water and there are no leaks in the system.
After filling the water heater tank with water and checking the tightness of the system, plug the water heater's waterproof electrical plug into the socket.

6. Electric water heater operation

6.1 Electronic model SHT=EL

Attention: Before turning on the water heater, make sure it is filled with water. Make sure that the water heater is properly grounded. Check the operation of the RCD (residual current device) that comes with the cable. Test instructions are located on the cable. The water heater control panel has an [On/Off] button, a [power] button, and [Plus] and [Minus] buttons to select the required temperature. As well as an indicator of heating and the selected power.

Turning on:
Plug in the water heater. Within 1 second, all indicators will light up, then the current temperature in the tank will be displayed on the screen. The temperature display will flash. This means that the water heater is in the off state. Press the [on/off] key to turn on the water heater.

Power level selection:
When the water heater is on, press the [power] button. Pressing should be short. This will allow you to change the power from 2500 W (indicator is on) to 1500 W (indicator is on)

Antibacterial function:
When the water heater is on, press the [power] button for about 5 seconds. This will enable the antibacterial function. The heating indicator will flash. This function will automatically heat the water up to 750C and will maintain this temperature for 3 hours. The water heater will then return to the heating settings you set before entering the antibacterial function. This function can also be turned off by pressing and holding the [power] button for 5 seconds.

Temperature setting:
In the on state, when the numbers are no longer flashing, press the [Plus] or [Minus] button to check the temperature settings. At this time, the system will enter the temperature selection mode. The numbers on the display should flash rapidly. The temperature can be changed from 300C to 750C in 1 degree increments. Temperature changes are made by pressing the [Plus] or [Minus] buttons. The water heater will maintain the set temperature automatically.

Warning:
Since the system does not have a memory function, when the water heater is turned off, the temperature settings are reset. When you turn it on again, the default settings are set: heating temperature 750C and heating power 1500 W.

Error codes displayed by the system:

If the water heater is switched on when the tank is not filled with water (the so-called “dry” switching on), the system automatically reads an incorrect heating gradient and switches off the water heater. Error code E2 will appear on the display

If temperature sensor depressurization or a short circuit occurs, the system will display an error E3

If the temperature rises above 900C, the system will display an error E4

In case of problems, contact authorized service centers

6.2 Mechanical model SHT

Attention: Before turning on the water heater, make sure it is filled with water. Make sure that the water heater is properly grounded. Check the operation of the RCD (residual current device) that comes with the cable. Test instructions are located on the cable.

The water heater control panel has an [On/Off] button, a [power] button and a heating temperature controller.

Turning on:
Plug in the water heater. By pressing the left button marked, the water heater is switched on and off. This key turns on the heating element with a power of 1500 kW. During the heating process, the left key will be illuminated. When the set heating temperature is reached, the button will turn off.

Power level selection:
When the water heater is on, press the left key marked. This key turns on an additional heating element with a power of 1000 W. Thus, the total heating power will be 2500 watts. During the heating process, the keys will be highlighted. When the set heating temperature is reached, the keys will go out. If the left [On/Off] key is pressed while the right [Additional power] key is pressed, the water heater will turn off and both keys will go out.

Temperature setting:
The water heating temperature can be adjusted using the temperature controller, if the water heater is switched on. Temperature control is carried out in the range from 300C to 750C. The water heater will maintain the set temperature automatically.

7. Moments that need attention

1. At the first start-up of the water heater, as well as at each start-up after switching off, make sure that the water heater is filled with water and only then connect it to the network.
2. If the power cord is damaged, it should be replaced with a special cord. This cord can be purchased from an authorized service center.
3. In winter and in cold areas, when the heater is not used for a long time, drain the water from the heater. To do this: close the cold water supply valve, open the drain valve (if there is a mixer, turn its regulator to the maximum temperature position), close the sludge removal drain (be careful not to scald), then drain the water.
4. Socket outlets must be properly grounded.
5. Clean the heater periodically during operation. Sequence of actions: disconnect the water heater from the network, shut off water faucet, open the drain valve by turning the handle, open the drain hole (be careful not to scald) and drain the dirt. It is advisable that this work be done by a qualified specialist.
6. If there is severe scale formation in the heating elements or a large number sediment, remove the heating elements and clean them. When reinstalling them, observe the following: the bolts must be tightened evenly, without significant application of force, the fixing support must not be tilted. The power supply can only be connected after filling the water heater with water.
7. If the heater is not used for a long time, turn off the cold water supply tap and disconnect the water heater from the mains.
8. If the water pressure exceeds 6 bar, water drops or leaks may appear on the outlet of the safety valve.
The rare appearance of water droplets on the drain hole of the safety valve indicates normal operation of the heater.
The frequent appearance of water drops on the drain hole of the safety valve means that the water pressure is too high. In this case, it is necessary to install a reducer on the cold water supply pipe to reduce the pressure, which should be located at the maximum distance from the heater.
To drain the resulting water droplets, a drain pipe can be used, the end of which must point downwards and not be closed.
9. Before contacting the service center, make sure that the malfunction of the device is not related to the shutdown of the cold water supply, power supply, etc. If the water heater is not powered, the water overheating safety thermostat may have tripped. In this case, contact an Authorized Service Center. Have your warranty card ready. It will be needed by a service specialist during the repair of Ariston.

Comfort modern apartment impossible without warm water. But public utilities are in no hurry to make our lives easier and more enjoyable. Therefore, it is necessary to independently take care of the presence of comfort in your home. Hardware stores offer us a huge selection of water heaters. Which one to stop?

If your home is not suitable for installation geysers, then opt for Ariston boilers 80 liters. This is the famous Italian trademark, which has become a leader in the design and manufacture of household appliances. In order to dispel your doubts, we will explain the boring instructions in an accessible language.

Features of the water heater

A characteristic feature of water heaters is built-in tank. Water accumulates in it, keeping the temperature set by the program. Such a model will become relevant for those who from time to time have problems with hot and cold water supply. Eighty-liter tank of the model, as indicated by the instructions, perfect option for a family of three. Wash the dishes, take a shower, bathe the baby.

The structure of the boiler resembles a thermos: in it, the liquid not only heats up, but also retains heat. Thermal insulation material occupies the empty space between the body of the water heater and the tank. Schematic representation The manual clearly shows this to us. Thanks to him, energy is saved: after all, you do not have to constantly maintain the temperature.

The inner tank of the water heater "Ariston" 80 liters is made of quality steel, which has an increased resistance to corrosion processes. The fact is that under the influence of aggressive environments (constant high temperatures, humidity, changes in water level), metal components suffer first of all. Therefore, the Ariston engineering bureau developed a special alloy, which received maximum resistance to rust corrosion.

The heating element of the water heater (TEN) has a reliable insulation. The feature of the model is heating element material - alloy, which may contain:

• copper;
• stainless steel.

Thermal power is increased by a brass flange.

One of the main parts of the Ariston boiler 80 liters is a magnesium anode. It is made of a special alloy and is attached next to the heating element. Its function is to protect the walls of the water heater tank from rust, to reduce the amount of scale. If you do not start fighting corrosion in time, then over time it will begin to corrode the metal walls of the container and, as a result, it will begin to let water through. Scale layers on the heating element will increase the heating time, which will lead to waste of electricity, and even breakage of the element. Entering into chemical reaction With aggressive environment, the anode shields the internal parts from negative impact. You, of course, will not read this in the instructions for the device, but to obtain general information healthy.

Intelligent control system in which even a schoolboy will understand. The ergonomic design allows you to place the Ariston 80 liter water heater models in a horizontal position. In addition, the equipment is reliably protected from overheating, high pressure.

Water heater installation

So you bought a boiler and carefully study the instructions. Remember that in order for the water heater to work reliably, all installation actions should be entrusted to the service center employees. In case of an error at self installation, warranty obligations technology does not apply.

Water heater: control system

Before turning on the water heater, you must make sure that there is water in the tank.

When the boiler is connected to the network, within one or two seconds, the temperature readings will be displayed on the screen of the water heater control panel. The instruction indicates that if the numbers flash, then this means only one thing - the device is still turned off. Click on the "On / Off" button (in the upper left corner) to start the technique.

There is a power control button on the remote control. It can be used to adjust the strength voltage from 2500 W to 1500. This function allows you to increase or decrease the time for heating water.

The temperature setting is activated by holding the button (plus or minus) for a few seconds. The range ranges from 30C to 75C. After installation, the water heater remembers the program, working in the specified mode. The instruction says: if the device is turned off, all settings are reset.

If you have not read the instructions to the end, then you do not know about the very convenient function of the water heater - protection against bacteria. Hot water is an ideal breeding ground for all kinds of microorganisms. And heat kills them. By enabling this option, you force the technician to increase the degree above 65, that is, to a level where microbes cannot exist, multiply. Once a month is enough for your water heater tank to be freed from all evil spirits.

Possible breakdowns

Water heaters "Ariston" 80 liters belong to the technique with a high degree of reliability. However, as sad as it is to say, damage does happen.

According to the repair service employees, the most “popular” breakdown is the failure of the electronic scoreboard. Do not panic, flipping nervously through the instructions, this does not affect the overall operation of the water heater. Experts also recommend using maximum temperature, but within 60C.

Heating elements for boilers "Ariston" 80 liters need to be changed from time to time. No matter how powerful anti-scale protection is, the quality of our water still does not improve. Therefore, after two or three years, your heating element will turn into a small pebble. If you do not open the water heater, then you can determine the presence of this unpleasant feature by increasing the heating time.

The instructions for the water heater indicate the marking commonly reported errors:

• E2 - an attempt to turn on the boiler with an empty tank;
• E3 - the temperature sensor is depressurized, a short circuit has occurred;
• E4 - in case of heating water up to 90C.

If you see any of the above on the water heater control panel, you need to contact the service center.

So, we examined the main characteristics of one of the popular models that Ariston water heaters represent 80 liters. With proper operation, compliance with all the rules of the instructions, this reliable device will serve you for many years. And a wide network of official service centers will nullify discomfort in the event of a breakdown.

When the boiler is turned on only when necessary, some nuances of its operation are often forgotten. With a standard heater connection scheme, you must follow the entire procedure so that the device works without interruption and lasts a long time.

The principle of operation of any boiler is simple: cold water passes into the tank, it heats up there, and hot water comes out. For the most part, heaters have the same components, which are:

• internal tank. It is made of anti-corrosion steel, which prolongs the life of the water heater and protects the internal elements from damage;
• a heating element;
• RCD (residual current device), which protects against voltage drops and overheating.

The device may only be installed by qualified personnel. Before installing the tank, it is necessary to check the serviceability of the electrical wiring. Specialists must make sure that the voltage in the network corresponds to the permissible voltage for the tank, specified in the instructions for use of the device. The use of adapters or extensions is excluded. In the same electric line connection of additional electrical appliances is not allowed. The outlet must be dry and away from water sources. If the power cord becomes damaged over time, it can only be replaced by a specialist.

So, the tank is already connected, how now to turn on the Ariston water heater ?. Instructions for use will help you connect the heater.

First you need to turn off the hot water supply in the apartment. Otherwise, the contents of the boiler will flow into the riser. Despite the presence check valve, turn off the water.

Open the faucet, wait until the water has completely drained. When the liquid stops flowing, close the valve.

Cold water and heated water enter the boiler and back through two pipes. On the tank, they are marked with a blue and red label, respectively. These mixers on both pipes need to be opened. First turn on cold water, then hot. If you forget to turn on the hot water faucet, it will flow through the riser to the whole house.

When the air comes out of the device, and the liquid flows in an even stream, the boiler can be connected to the power supply and the desired program can be selected. Do not block the cold water pipe, the supply to the boiler is regulated automatically.

After five minutes, check the water in the tap, its temperature should increase. If so, then you did everything right.

There are also compact water heaters. Mounting such devices will not be difficult. They are installed in place of the old crane. After installation, the tank must be connected to a pipe through which cold water flows. Then turn off the hot water faucet and plug the appliance into the outlet. Turn on the water and you're done. To install such heaters, it is still better to contact specialists.

Any heating tank must be connected to a separate outlet, which is removed from sources of moisture.

When the boiler is finished using, it must be turned off. How to do it? Unplug the cord from the tank. Wait for the water in the tank to cool down. Close both taps, one of which supplies water to the tank, and the second releases hot water. After that, open the hot water riser.

If the boiler is used from time to time, then it is not necessary to drain the water from it. Water contributes to the fact that the parts in the device are less corroded. Drain the water just before using it again. When you do this, rinse, dial clean.

If a situation arises when the boiler needs to be emptied of liquid, then this can be done using the check valve installed on the device.

Be careful! When the tank is empty, its inclusion is strictly prohibited!

In order for the Ariston water heater to serve you for a long time, it needs care. Every six months it should be cleaned to protect the heating element from breakage. Any malfunction is best repaired by specialists. To notice this, pay attention to the following:

• water heats up noticeably longer;
• hissing is heard during operation of the device;
• the heater turns on and off more often.

With proper operation and timely care, the unit will last a long time, since Ariston uses only original spare parts for its devices. Heating elements are made of high-quality copper, a special system protects the device from overheating and freezing. Models are characterized by a flat shape, easy installation. Tanks are produced in volumes of 30, 50, 80 and 100 liters. The devices have a water purification system from bacteria. The displays are functional and easy to use.