Instructions for using the water heater Ariston. "Ariston" (water heaters): instruction

18.10.2019

Convenient connection of water-heating equipment from the company "Ariston" consists in the use of manufacturers of an autoclave special flange mechanism. The basic principle of operation of such a mechanism is based on pressing the gasket under the influence of water pressure. As a result, it is possible to completely eliminate not only the leakage of liquid, but also the formation of watery smudges. To avoid excessive heat loss, fastening electrical models water heater from the company "Ariston" is carried out in close proximity to the point of output.

Water heater for a shower in the country houseHeating water in the pool

Water connection

Next comes the connection to the water supply. A scheme is thought out, first drawn on a piece of paper, and then transferred to the walls with real dimensions. Along the lines where the pipes will pass, holes are drilled and clips are installed.

We close the valve at the water inlet, install a tee on the branch closest to the boiler. From it is a pipe to the water heater. A valve is installed on it so that it is convenient to repair the device, a strainer and a check valve.

We lead a flexible hose to the boiler and connect it to the pipe. Usually the input is marked in blue. In the same way, we draw a branch to the watershed point. It is not advised to connect without flexible hoses. On the one hand, it looks better and more reliable, but if there are sudden pressure drops, the tank takes the whole blow.

The inlet to the boiler is marked in blue

After connecting all the nodes, the valves open and all connections are checked for leaks. If they are found, reconnections are made or more tow is added to the threads.

Description of anode rods

The magnesium rod eliminates corrosion of the inner walls of the tank, and also softens the scale that forms on the heating element during the operation of the water heater. It is a magnesium alloy rod on a metal threaded stud and is screwed to the heating element flange, together with which it is inserted inside the water heater tank. The hole thread diameter ranges from M4 to M8 depending on the size and weight of the magnesium alloy on the stud. The larger the size and weight, the thicker the magnesium anode stud. The diameter of the magnesium anode is from 14 to 25 mm. The length of the magnesium part without the stud is from 140 to 660 mm.

Operating principle

The water entering the water heater contains soluble calcium and magnesium bicarbonates, which are present in it in the form of Mg2+, Ca2+, HCO3- ions. Magnesium is the first to react with water, since it is more active than iron and binds free oxygen formed during heating due to a multiple increase in the amount of Mg2+ cations. When the anode is installed in the tank, not hard scale (CaCO3) is formed, but soft scale (MgCO3 or Mg(OH)3), which is easier to remove when cleaning the water heater, or which itself falls to the bottom of the tank during the operation of the water heater due to thermal expansion or contraction of the heating metal element. Over time, the anode will dissolve, so it is advisable to check or replace the magnesium anode once a year, or follow the water heater manufacturer's instructions.

Is it necessary to install a magnesium anode in a water heater?

Modern boilers have tanks made of stainless steel, with titanium, glass-porcelain, enamel coating. In this case, the tank corrodes at the welds and begins to leak over time, so it is necessary to regularly replace the magnesium anode. If it was not originally in the water heater, then it must be installed in the case when scale forms on the heater. In this case, the manufacturer most likely performed welding using a special technology or even made the tank one-piece, without welds. Without an anode, hard scale is formed, which has a lower thermal conductivity. This increases the heating time and the amount of energy consumed, reduces the efficiency, there is a constant overheating of the metal of the heating element. In the end, this leads to its rupture and failure. Therefore, timely and regular replacement of the anode will allow your water heater to work for many years.

What to look for when choosing a magnesium anode?

The main selection criterion is the diameter of the thread on the stud so that the anode can be fixed on the heating element flange or nearby, if such fastening is provided. The second criterion is the length, since meter ones, for example, simply may not fit. The next criterion is thickness. Anodes with a large diameter can touch the heater tubes, although in this case the plate with the mounting hole can be bent. The next criterion is the length of the stud. This choice is rare, as certain electric heaters require a long stud to keep the heating tubes out of the way.

thread diameter on the stud;
length;
thickness or diameter;
threaded stud length.

Prices for the main models name, description, manufacturer, price

When it comes time to buy a heating device, it is immediately better to pay attention to the Ariston 80 liter water heater, the price of which is fully consistent with the quality. Consider some models of heaters from this manufacturer.
.
ARISTON ABS BLU R - vertical storage water heater

The price ranges from 6300 to 7700 rubles.

ARISTON ABS BLU R – vertical storage water heater. The price ranges from 6300 to 7700 rubles.

It has an anti-corrosion coating Ag +;
Additional protection in the form of a magnesium anode;
Uniform heating of water is provided by the Nanomix technology;
Thanks to Absolut Bodyguard System technology, the system is blocked in the event of a lack of water or power surges;
Built-in safety valve.
Built-in external thermometer.
Mechanical control with indicator.
Water heating up to 75o is carried out in 3 hours with a consumption of 1.5 kW.

Boiler ARISTON BLU R - Photo 12

Ariston vls pw 80

water heater ariston vls pw 80 – wall-mounted heater with the possibility of mounting horizontally and vertically. The price for this model varies between 11,000 - 13,000 rubles.

The inner tank is treated with a special Ag+ coating;
Double heating element accelerates water heating by 60% after connecting the ExraPower mode;
ABS 2.0 protection protects the system from power surges and operation in the absence by turning it off.
External water temperature sensors allow you to monitor the state of water heating;
Built-in ECO antibacterial system;
The Nanomix technology accelerates the heating of water, which contributes to the uniform heating of the liquid.
Water is heated up to a maximum value of 80o at a power of 1.5 kW in 3 hours, at a power of 2.5 kW in 2 hours.

Water heater functions

Ariston SUPER SGA

Ariston SUPER SGA – excellent gas heater made in Italy. The price of such a storage water heater is 16,500 rubles.

Device characteristics:

Steel case;
Internal enamel anti-corrosion coating;
Thermal insulation layer made of polyurethane foam;
The presence of a gas valve.
Connection can be carried out both in parallel and in series;
Works independently of the mains;
Ability to control the flame;
External regulators and indicators.

Flat electric water heater Ariston ABS VLS INOX PW Can be installed in vertical and horizontal position. The price for such a model is 17,250 - 19,930 rubles.

Main characteristics of this model:

Steel inner tank with additional protection;
The “fast” function speeds up the heating process by turning on the second heating element;
Antibacterial protection system;
Protection against overheating, power surges, switching on without water;
Built-in “Nanomix” system;
The presence of an electronic thermometer;
There is a system "Autodiagnostics";
External display with control buttons.
Water heating is carried out to a temperature of 80o by one heating element in 3 hours 06 minutes with a consumption of 1.5 kW, with the “fast” system turned on in 1 hour 51 minutes with a consumption of 2.5 kW.

Advantages of Ariston technology

Like all Ariston appliances, the water heaters of this company have a lot of benefits:

The first of these can be called stylish design which helps to decorate any interior. Moreover, each of the models is created in accordance with the latest technologies.
Ariston 80 water heater is different longest service life . This effect was achieved due to the fact that internal walls storage tank covered with a layer modern material which protects the tank from plaque and rust.
Built-in latest dividers, prevent mixing of already heated and cold water . This allows you to keep the temperature of the liquid. Also, the Ariston heater is protected from overheating, thanks to built-in temperature control sensors.
Presence of a safety shutdown device , which is triggered at moments of a sharp change in voltage.
Using Ariston water heaters, users can significant savings on gas or electricity consumption . This is facilitated by the presence of thermal insulation, which keeps the water hot for a long period of time.
Many models of water heaters equipped with bacteria protection which makes it possible to use purified water. If there is no water in the system, then you do not have to worry that the water heater will turn on, as it is equipped with special protection.

Repair

If we break down the repair actions of the units into several stages, they will be as follows:

It is necessary to diagnose the type of failure.
Determine the fault
Replace the failed assembly or part.

Features of water heaters "Ariston"

We are considering the repair of the Ariston electric boiler. Models from 50 to 100 liters. One of the advantages of the models of this company is the use of a classic autoclave flange. This solution does not allow water to flow through the gasket. The gasket is pressed against the pressure of the water in the water heater. The larger it is, the greater the tightness. But Chinese manufacturers have learned to fake this gasket, therefore, when purchasing it as a replacement, you need to look for a “native” one, avoiding fakes.

Boiler "Ariston"

The next feature is that the heating element is equipped with an elongated knife contact, so heating elements from other manufacturers are not suitable.

The water heater is supplied with a magnesium anode.

Examination

Before starting the repair of Ariston water heaters, it is necessary to check whether there is electricity in the house and whether the water has been turned off. Often this factor misleads inexperienced users.

The next step is to check the correct connection to the mains and cold water. If these positions are maintained correctly, then the problems should be sought in the following:

The circuit breaker is off.
The automatic safety device has been activated.
The heating element burned out.
Electronics broke.

Replacing the heating element

If you find out that the heating element has burned out, then it needs to be replaced. Try to repair the Ariston water heater with your own hands.

Self repair

For this you need:

Disconnect the boiler from the power and water supply.
Unscrew the two screws and remove the protective box.
Turn off the power that is directly connected to the heater.
After unscrewing two more screws, remove the cover of the water heater.
Remove temperature sensor and thermostat.
Remove from water inlet check valve and drain the water from the boiler.
Unscrew the fixing nut with an adjustable wrench and remove the fastening on the bar to which the flange is attached.
Move the heating element inward, unfold and pull out. Do this carefully so as not to damage the flange. Don't forget to put a container under the flange, as water will still flow.
Replace the heating element or clean the flange and tank from dirt. It is not recommended to remove scale from the walls, as this is an additional protection of the tank from corrosion. Remove only the scale that has crumbled inside or is easily cleaned with a rag.
Replace or clean magnesium anode. It spins next to the shade.
Replace all parts in reverse order.

At the end of the assembly, check the tank for leakage. If it leaks, replace the gasket.

When replacing the flange, it is important to put the same design as it was. Otherwise, the gasket may break, and the boiler will start to flow.

A heating element

If you do not regularly clean the water heaters, then the anode and the heating element will collapse, despite the good adaptation of Ariston products to our water. Therefore, it is so important to regularly inspect and repair the Ariston boiler, you can do it yourself.

Fake Parts

Connecting the boiler Ariston

It is better if this work is carried out by specialists. The rules to be followed when installing the device are given below:

It is necessary to inspect the safety valve, which should not have visible flaws. If they are, then the damaged part should be replaced.
Plastic dowels are used for driving screws.
Be sure to check all grounding elements.
The electric heater requires a separate power line to operate. The use of extension cords is strictly prohibited. The socket is placed in a non-humid place.
In operation, you must use the plug that came with the kit.

The water heater Ariston 80 performs the following functions :

Turn on/off . After switching on, the whole system starts up, which is due to the lights on, the temperature of the water in the boiler will be displayed. If the indicators are not displayed or flashing, this indicates a system shutdown.
Water heater ariston abs vls 80 has power level adjustment function , which makes it possible to set the necessary indicators.
Water heater ariston abs vls pw 80 allows you to use antibacterial function , which can be activated or deactivated by holding the "power" button for 5 seconds.
Possibility to adjust the temperature using the "+" or "-" buttons in the range from 30o to 75o; The set values are not fixed. After switching on again, the values \u200b\u200bmust be set again. Standard temperature values are 75 °, power - 1500 watts.

Water heating

Depending on the volume of the tank, the time of the first heating will differ. It takes about an hour to heat 30 liters of water to 65 degrees, 50 liters two hours, and 80 liters three hours. Also, the time depends on the heat of the incoming water and the power of the apparatus. In winter, the water comes in cold and it will take longer to warm up.

Boilers with more powerful heating elements spend less time and more electricity on primary heating. For example, Ariston Platinum SI 80 H with a volume of 80 liters and a heating element of 1.5 kW heats water from 20 to 65 degrees in 3 hours and 6 minutes.

For two people, a volume of 30 liters is enough, fifty is enough for a family of 3 people. An eighty-liter model should be enough for 4-5 people living in the room where the water heater is installed. Also, the consumption largely depends on the habits and purposes of using hot water.

The system for using the heater is very simple and straightforward.

The device may only be installed by qualified personnel. Before installing the tank, it is necessary to check the serviceability of the electrical wiring. Specialists must make sure that the voltage in the network corresponds to the permissible voltage for the tank, specified in the instructions for use of the device. The use of adapters or extensions is excluded. It is not allowed to connect additional electrical appliances to the same electrical line. The outlet must be dry and away from water sources. If the power cord becomes damaged over time, it can only be replaced by a specialist.

So, the tank is already connected, how now to turn on the Ariston water heater ?. Instructions for use will help you connect the heater.

First you need to turn off the hot water supply in the apartment. Otherwise, the contents of the boiler will flow into the riser. Despite the presence of a non-return valve, turn off the water.

Open the faucet, wait until the water has completely drained. When the liquid stops flowing, close the valve.

See also: How exactly does an instantaneous water heater work?

Cold water and heated water enter the boiler and back through two pipes. On the tank, they are marked with a blue and red label, respectively. These mixers on both pipes need to be opened. First turn on cold water, then hot. If you forget to turn on the faucet hot water, then it will flow along the riser to the whole house.

When the air comes out of the device, and the liquid flows in an even stream, the boiler can be connected to the power supply and the desired program can be selected. pipe with cold water do not block, the supply to the boiler is regulated automatically.

After five minutes, check the water in the tap, its temperature should increase. If so, then you did everything right.

There are also compact water heaters. Mounting such devices will not be difficult. They are installed in place of the old crane. After installation, the tank must be connected to a pipe through which cold water flows. Then turn off the hot water faucet and plug the appliance into the outlet. Turn on the water and you're done. To install such heaters, it is still better to contact specialists.

Any heating tank must be connected to a separate outlet, which is removed from sources of moisture.

When the boiler is finished using, it must be turned off. How to do it? Unplug the cord from the tank. Wait for the water in the tank to cool down. Close both taps, one of which supplies water to the tank, and the second releases hot water. After that, open the hot water riser.

If the boiler is used from time to time, then it is not necessary to drain the water from it. Water contributes to the fact that the parts in the device are less corroded. Drain the water just before using it again. When you do this, rinse, dial clean.

If a situation arises when the boiler needs to be emptied of liquid, then this can be done using the check valve installed on the device.

Be careful! When the tank is empty, its inclusion is strictly prohibited!

In order for the Ariston water heater to serve you for a long time, it needs care. Every six months it should be cleaned to protect the heating element from breakage. Any malfunction is best repaired by specialists.

To notice this, pay attention to the following:

water heats up noticeably longer;
hissing is heard during operation of the device;
the heater turns on and off more often.

With proper operation and timely care, the unit will last a long time, since Ariston uses only original spare parts for its devices. Heating elements are made of high-quality copper, a special system protects the device from overheating and freezing. Models are characterized by a flat shape, easy installation. Tanks are produced in volumes of 30, 50, 80 and 100 liters. The devices have a water purification system from bacteria. The displays are functional and easy to use.

Do-it-yourself Ariston boiler repair

Repair work related to the elimination of breakdowns in gas appliances require the involvement of qualified specialists, and the repair of an electric boiler can be done independently.

Major mechanical failures are most often manifested by tank leaks., from which water begins to ooze or drip during operation. The cause of this failure may be corrosion in the weld areas or a malfunction of the reverse protection system of the valve, which operates and performs an emergency reset. In this case, it is necessary to eliminate the excess level of water and air pressure by means of a reducer. Any depressurization of the storage tank will require the purchase of a new tank. If such a defect is insignificant, then it is enough to replace the sealing gasket.

A fairly inexpensive measure is the independent replacement of some electrical parts, including a heating element, a bimetallic thermostat, sensors or switches. In case of prolonged heating, noise or hiss, as well as in the event of an ABS system shutdown protection, a replacement of the heating element is required, the average service life of which does not exceed five years. Replacement is carried out after de-energizing the device, draining the water and removing the flange.

It is very important to systematically check the magnesium anode, which is a consumable item and is intended for effective protection the inner surface of the tank and the heating element from corrosive changes. When the anode is thinned by ½ of the original volume, a mandatory replacement is carried out

The heating element is able to last much longer if the so-called “dry” heating element is installed in the structure.

Installation

Do-it-yourself Ariston is a simple matter if you carefully read the instructions and follow its instructions. Of course, you can invite specialists who will do everything quickly and efficiently. The only “but” is the price of this service. For example, in Moscow it is from $100. Meanwhile, having minimal skills in working with plumbing, you can cope with this task in just 2-3 hours. Considering that you will spend some amount on Consumables, the net savings will be approximately $60.

Water heater connection diagram.

Evaluating the pros and cons, consider the risk of flooding the neighbors from below, if something goes wrong, measure your strength. The advantages of self-solving this problem include:

saving time and money;
acquisition of skills that you will need in the process of operating the water heater.

Access to the storage water heater (boiler) must be absolutely free, and the wall for fastening must be strong, capable of withstanding double the weight (with a unit capacity of 50 liters, calculate the load of 100 kg). Determine the condition of your electrical wiring: is it capable of handling a significant additional load? For example, for a water heater of 2000 W, there should be a copper wire cross section of 2.5 mm². Keep in mind that if you have old water pipes in an apartment, sometimes you have to first replace them and only then connect the boiler. Find out how much current your electricity meter is designed for. If less than 40 A, you will have to replace it.

Back to index

Turning on

If you are turning on the boiler for the first time, you should do the following:

We examine the inlet pipes to the water heater and find the check valve. If the normal pressure is exceeded, water will pour out of it. Therefore, you should either substitute a small container under it, or connect and bring the tube into the sewer.
We collect a tank. We open the valves at the inlet and outlet of water from the device. To do this, turn the handle of the taps 90 degrees counterclockwise. Open the hot water faucet. We are waiting for the container to be filled. If water starts to flow, this means that the Ariston boiler is full.
It is advisable to visually inspect the pipes for leaks. If water drips somewhere, it is necessary to turn off the water and call specialists to fix the breakdown.
We turn on the device in the network. To do this, either insert the plug into the socket, or turn on the machine to which the electric cable is connected. The machine may be located near the installation site or in a switchboard.
Set the desired water temperature. It is recommended to set the level of 60-65 degrees. At higher temperatures, scale actively accumulates, and at lower temperatures, harmful bacteria can begin to multiply.
The temperature can be set with a mechanical knob, as in the Ariston SG 30 OR model, or with buttons on the control panel, as in the Ariston VELIS EVO PW model.

After that, it remains to wait until the liquid heats up and start using hot water. For convenience, you can mix cold tap water with warm water from the boiler to achieve desired temperature.

Water heater Ariston

It is very important to prepare in advance all the tools and consumables for the work. Before starting installation, make sure you have the following tools: .

Tools for mounting storage water heater.

roulette;
perforator with a drill;
wrench;
spanners;
wire cutters;
pliers;
two types of screwdrivers.

Consumables:

Unipack type paste or FUM tape;
tow;
3 stopcocks;
3 tees;
2 connecting flexible hoses (if not included);
metal-plastic pipe of the required length.
if it is necessary to replace the wiring - a three-wire wire, a socket or an automatic machine.

To install a storage electric heater, you will need an auto switch for 32-40 A, a PVA cable 3X6 -3X8.

Back to index

Installation

Installation of the water heater "Ariston can" is done by hand.

Installation of the Ariston water heater must be carried out in strict accordance with the instructions.

Installation instructions for the Ariston water heater, of course, are included with the purchase of the unit.

It is necessary to check the outlet and test the voltage in the electrical network. The socket must be grounded and have a separate wire from the shield.

Fastening

Since the weight of the device will be quite heavy due to the large amount of water, the wall on which it will be installed must be strong. The bolts with which this structure will be attached must also be strong. It is better to use metal fasteners: hooks, bolts, screws, with a diameter of 10mm. The connection of the Ariston water heater should be close to the place of hot water supply so that there is no unnecessary heat loss. It is necessary to clearly mark the place of attachment of the water heater using a level and a tape measure. Make sure that the load is evenly distributed, there are no distortions. Using a drill, holes are drilled in the wall, to which brackets and holders are attached, on which the boiler is hung.

Some models are installed on the floor. In this case, the symmetrical installation is adjusted by the feet of the appliance.

Connection to the water supply system

The hoses and other connecting elements used for connection must withstand the design pressure and temperature of about 80 degrees. When connecting to a water supply system, it is best not to connect two different metals to each other, such as copper and steel (in pipes). To do this, you need to use a dielectric adapter.

With the help of a valve included in the device, a pipe for cold water is connected. The hot water pipe is connected using a pipe. Your task is not to confuse these two inputs when connecting the Ariston boiler.

Start installation with a cold water pipe, it is marked in blue. A sealing tape or tow is wound on the pipe. If you take tow, then it must be lubricated with a special paste. Then the tee is screwed on. There will be a relief valve at the bottom of the tee. It is installed in an upward direction. This valve will control pressure and superheat. On the side of the tee we put an emergency drain valve. You will use it if you need to completely drain the water from the boiler.

The shut-off valve is placed at the bottom and the boiler is connected to the water supply through an adapter.

Also, through a shut-off tap and an adapter, a connection to hot water is made.

The correct scheme for connecting the Ariston water heater to the water supply is shown in the video:

Electrical connection

Only after the connection to the water is made, we connect it to the electrical wiring. Since this unit consumes a lot of electricity, the wires must also meet the requirements.

Connecting the Ariston water heater to the mains is as follows:

Disconnect the water heater from the electrical network.
The power supply wires are connected to the screw terminals of the thermostat.
Be sure to observe the phases when connecting: - L, A or P1 - phase wire; N, B or P2 - neutral wire.
Connect the ground wire to the clamp on the boiler body.
Connect the test lamp terminals to the terminals.
Press the thermostat button.
close lid
Before switching on the power supply, it is necessary to check the filling of the boiler with water.
Turn on power.

Scheme of connecting the boiler "Ariston" to electricity through a double circuit breaker:

Boiler connection

The electric wire for the boiler must pass through the wall or be hidden in a corrugation made of non-combustible material. The connection cable must be three-core, preferably copper. Installation of the Ariston water heater must provide for grounding. Grounding is not done on metal objects and pipes, such as sewers, plumbing, and so on.

Beginning of work

Before starting work, you should once again make sure that the flange is exactly in the center. If it is slightly off to the side, install it correctly (loose or tighten). After filling the tank with cold water, open the hot water outlet cock on the boiler to allow excess air to escape, then close it.

When you turn on the heating pressure on the body of the water heater, the lamp should light up. Sometimes during operation, the cold water hose heats up. In some Ariston models, the temperature can be adjusted with a special knob connected to the thermostat with a screw. Economy mode is marked on the unit with the letter "E".

In the event of an unexpected breakdown or malfunction of the new water heater, you can contact the warranty repair shop in your city. The usual warranty period for the Ariston boiler is 1-2 years, depending on the model (the same as for the Termex, Bosch or Nova Tek water heater). If before the expiration of this time you tried to open and repair the unit yourself, then most likely you will be denied free warranty service. Keep the warranty card issued by the store until the end of the warranty period.

The storage water heater from the company "Ariston" - the unit is quite simple to operate and reliable. If you strictly follow the instructions during installation and when further use, it will serve you faithfully for more than one year.

Boiler installation

Accumulative water heaters heat water for a certain time in special tanks from 10 to 150 liters and more. In small city apartments, most often they put boilers of 50 or 80 liters. Fastening to a fragile wall (for example, drywall) is excluded. There is no fundamental difference in installing a small or large tank, except that the larger the unit, the more powerful the fastening elements.

Scheme of the storage water heater.

Break the work into several stages. The main and most important stage is fixing the boiler to the wall. If the container is horizontal, it is advisable to attach it higher, under the ceiling, if it is vertical - at the level of the person's head or chest. Under the boiler, the floors must be waterproofed in case of leakage.

You need to work carefully, avoiding scratches and damage to the outer surface of the unit from tools. It must also be borne in mind that the electronic control unit of the boiler does not have an autonomous power supply, in case of any power failure, the settings will fail and a restart will be required.

Use bolts, hooks, screws with a diameter of at least 10 mm. Using a tape measure, mark the level of the attachment points. Make sure that all dots on reverse side of the unit provided for installation have been used, do not skew. Drill holes with a drill, then attach brackets and holders to them, on which the boiler is hung.

Each property owner wants to equip his house with an autonomous plumbing system that supplies hot water. So hot water can be used all year round, regardless of the season or schedule of the centralized installation. The 50-liter Ariston water heater is in great demand because it has a wide range of advantages.

A water heating boiler is a specialized device that performs the function of heating water with further stable maintenance of the temperature regime for a long time. What exactly is interesting about the 50-liter model and what models the manufacturer offers - in our article.

Equipment classification

Units of this manufacturer are divided into several classifications based on the following parameters:

Water heaters are accumulative, flowing, indirect;
Floor or wall type devices;
Equipment that runs on natural gas or electricity.

Each device has a specific heating system, a control unit, fasteners corresponding to the classification and other additional options.

Purpose of the tank

Household units powered by electricity are often used during the period when the water supply from the centralized pipeline stops. For short-term use, small wall-mounted storage water heaters are purchased. At competent installation, the device will provide the house with a supply warm water, which can be used to fulfill all household needs: washing dishes, wet cleaning, washing things or taking a shower.

In private cottages, in combination with gas boilers, gas or electric type heaters are used, which have large dimensions of the storage tank. In this case, the Ariston boiler is used year-round.

Rating of the best Ariston water heaters for 50 liters

The Italian company produces many modifications of water heaters, differing in the type of heating, volume, shape and other important technical specifications. We offer to consider the most popular models.

Ariston (50 liters) VELIS INOX

The wall-mounted device can be installed in a horizontal or vertical position. It is characterized by relatively low cost and medium volumes. The flat shape of the unit allows you to mount equipment not only on the open area of \u200b\u200bthe wall, but also in a niche.

The Ariston water heater is equipped with copper heating elements and power up to 2500 watts. In addition, the device has a protection system located on the electrical cord and a fuse that prevents unexpected start-up of devices with an empty tank.

Short description:

Ariston ABS VLS INOX QH

The external parameters of the model have significant similarities with the previous modification. The unit is equipped with automatic equipment that quickly heats up and thoroughly filters the liquid. In addition, the device regularly monitors the temperature regime of the coolant itself, warning the electric water heater from overheating.

Ariston ABS VELIS PW

The inside of the equipment is covered with a protective layer developed in accordance with the innovative AG + technological scheme. The equipment is equipped with a system of protection against bacteria and two heating elements.

When assembling the device, a special welding technology was used, providing a strong and monolithic connection, which eliminates the possibility of leakage.

Ariston ABS PRO R SLIM

The cylindrical shape of the equipment allows you to install the unit in any convenient corner of the room. Accumulative electrical elements produce rapid heating of the liquid. The budget version is divided into classifications by displacement - 30, 50, 65 and 80. You can buy a unit at an average cost - from 8,000 to 14,000 rubles.

First power on

In order for the device to properly perform the functions for its intended purpose, you need to follow the selection recommendations, install the equipment and make the first switch-on, taking into account all the rules. Most Ariston water heaters are characterized by the following step by step instructions launch:

First of all, the cold water supply valve opens. It is very important not to confuse the element with the safety lever.
At the same time, open all mixers that receive a hot stream of liquid. The faucets will produce loud sounds and the pressure will be intermittent.
Wait until the tank is completely filled when a steady stream of water comes out of the faucet.
Turn on the power, set the temperature to medium.

It will be possible to increase the degree of heating after the first start-up of the equipment.

Very important in a water heater accumulative Ariston 50, 60 or 100, fix the lever in the required position, which is responsible for supplying hot pressure. If you ignore the situation, the heated liquid can enter the common riser of the house.

VIDEO: Water heaters ARISTON. Installation and installation

Repair work

Like any other technique, an electric storage water heater of 50 liters is flat or rounded, has vulnerable elements. In this case it is:

Thermoregulatory system;
Heat transfer sensors;
Switches;
heating elements.

Valves or gaskets are often the first to fail. The integrity of the boiler is violated in rare cases. The reason for this can be corrosion formations and improper operation. In case of serious damage, you must contact the service department.

Repair of Ariston 50 at home provides only preventive processes associated with the timely cleaning of heating elements. Experts recommend cleaning parts at least twice a year.

First signs of breakdown

During operation, the device emits a hiss.
The average amount of time spent on heating water has increased significantly.

Before proceeding with repair work, it is necessary to carry out preliminary preparation of the device. To begin with, the power supply is turned off, the liquid is drained from the system, the water supply is shut off.

The most optimal option for descaling is considered lemon acid previously diluted in water. The liquid is poured into the tank for a day, after which the mixture is poured out and the container is washed from the remnants of plaque with clean water.

The magnesium anode helps to solve the scale problem, in which the potential limit is lower than that of the tank coating and the heating element itself. If to speak plain language, the process of rust formation begins precisely from the anode, and only then it “spreads” to the heating element and inner surface tank. With regular replacement of the anode (on average 1 time in 8-12 months), the heating element will not need to be cleaned, and the equipment itself will work properly.

All modern water heating equipment is already equipped with removable magnesium anodes. The user is only required to timely replace with original consumables.

If necessary self replacement parts, only original parts should be purchased. Spare parts can be ordered from a specialist dealer or from direct suppliers.

Disadvantages of Ariston 50 l, 60, 100

Requires regular preventive maintenance to clean the heating element from scale. If you clean the heating element less often, this will lead to a quick breakdown of the device.
Uneconomical consumption of electricity.
Expensive repairs and spare parts.

VIDEO: Ariston water heater repair

For the convenience of quickly obtaining hot water in the room, regardless of central heating, storage electric water heaters - boilers were developed. The range of electric heaters is very wide. Today we will take a closer look at the instruction manual for one of them, namely, the Ariston water heater.

Your task is to use it correctly

Having purchased Ariston electrical equipment for the home, do not forget to carefully study the instructions and always have it "at hand". Follow instructions should not in any way be skeptical and underestimated, since it is, first of all, your safety. Even if you accidentally lost the instructions from the device, you can get its electronic version specifically for your Ariston model on the official website of the manufacturer. People who create electrical devices, test them, test them, put the maximum useful information in the manuals for use and operation with the only important purpose - that you use them correctly. The same article will discuss General requirements and introductory moments.

Boiler diagram Ariston 50

Boiler designs have approximately the same construction scheme. It has a body, a water tank (the boiler itself), and a heating element (otherwise a heating element, sometimes there are several of them in the configuration). Be sure to install a magnesium anode next to the heating element, which prevents the formation of scale. The boiler itself from the outside and in its inner part has an insulating layer.

Two pipes lead to the water heater - one for supplying hot water, the second for cold. Boiler bodies can be cylindrical or flat. The boiler tank can have a different capacity - from 30 to 100 liters. The basic principle of operation of the boiler is to heat the water in the tank and maintain its constant temperature, set by a person, depending on the need.

What you need to know about Ariston boilers

The main function of Ariston water heaters is to provide houses, apartments, cottages, cottages with hot water for household purposes. In order for the electric water heater to serve for a long time and with high quality, the following characteristics:

It should be noted that the instructions for water heater models that differ only in the system of different volumes of the same series are almost identical. There are two types of heaters according to the principle of operation: flow-through (the heat exchanger heats the temperature instantly as soon as you open the tap) and storage (water is drawn into the tank and then heated). Storage water heaters, or boilers, have compact tank, designed for different volumes - 30, 50, 80, 100 liters. Boilers are of direct heating (they themselves heat water using gas or electricity) and indirect (such devices are located near the heat exchanger, for example, a boiler).

Installation of the device must be carried out by a specialist, otherwise your equipment will lose the right to warranty service. After installation electric water heater check the following:

About installing an electric water heater Ariston according to the instructions

Before installing the water heater, make sure the wiring can handle the added power. It is especially important that the outlet to which you are going to connect the device is grounded and not in contact with water. The power supply to the water heater must go from the shield on a separate cable. When choosing a place to install an electric water heater, consider its weight together with water in three times the size and the strength of the walls.

For fastening, hooks with a size of at least 15 mm are required. It is recommended to install a water heater in the immediate vicinity of the displacer, which will also reduce heat loss when water is supplied to the point of analysis. The distance from the ceiling is at least 10 cm, the space around the device is within a radius of at least 50 cm for technical work.

Under what conditions should the device not be installed?

If the water is hard, you must additionally install a filter, otherwise the water heater will quickly fail. It is impossible to install the device in rooms, the temperature regime of which may have a negative indicator, to exclude the influence of factors dangerous for the device - dampness, frost, direct sunlight, dust and insects. Maximum avoid splashing water, steam on the body of the device, that is, it is not recommended to install it directly above the bathtub.

With low water pressure, it is necessary to set the maximum temperature, otherwise the device may not turn on at all.

Only branded parts

All parts of the water heater, when first installed, must be in good condition. Especially it concerns safety valve. If damage is noticeable, the part should be replaced with a similar one. In no case do not use adapters or extension cords, do not replace the water heater plug with another one. Separate power line required to power the boiler. If the power cord is damaged, replace it with a similar one.

When turning off the electric heater, use a two-pole switch, the gap between open contacts is from 3 mm. Also pay attention to the fact that the pipes to which the water heater pipes will be connected have withstood temperatures above 80 degrees Celsius and the maximum working pressure.

Precautionary measures

If you know that you will not be using the appliance for a while, simply drain all the water from it. To do this, turn off the power to the device, close the cold water supply valve at the water heater, and open the hot water tap on the mixer. Open the tee drain valve. A magnesium anode that wears out over time should be replaced with a similar one. The first start-up of the device should be carried out strictly according to the instructions.

Prevention

With frequent use of the boiler, the first technical inspection should be carried out in six months or a year. Every 3 months it is recommended to drain the contents of the tank in order to remove sediment, which prevents heat transfer and reduces the efficiency of the heating element. It is also recommended to replace the magnesium anode after a year of operation of the device. Never ignore the error codes that appear. You can see in detail what each of them means in the instruction manual.

Today, Ariston water heaters are one of the most popular on the market. In particular, the 50 liter models are in particularly high demand. Such water heaters have small dimensions, so they can easily fit in any room. Ariston water heaters easy to operate, maintain and have a long service life.

Peculiarities

Ariston heater able to heat water from +30 to +85 degrees. An interesting feature of this product is that such a water heater has an extremely pleasant and user-friendly design, able to fit into any room, and constantly provides the house with hot water. Many models also have an energy saving function - the water automatically heats up to a temperature of +50 degrees. Of course, you can increase this figure if you wish. Also, Ariston 50 liter boilers can automatically turn off when there is a power surge, which helps prevent damage to the unit. In modern models, it is worth noting the functions of accelerated heating and water filtration.

Kinds

Among the main models of Ariston water heaters, there are several types.

Water heaters accumulative type. Two tubes and power supply are connected to the storage heaters. The first tube is designed to supply cold water to the boiler. After heating it, it exits through the second tube. Typically, 50 liter models are mounted - they are attached to the wall. Water in these types of boilers is heated by electricity. Thanks to the thermostat, the storage electric boiler automatically turns off after the liquid is heated to the desired temperature. Users noted Ariston VLS storage boilers, which, among other things, are flat. They are extremely compact, so they do not take up much space.

Boilers of gas type. Gas models differ in that they heat water not at the expense of electricity, but with the help of gas. Otherwise, the device and the principle of operation are similar to storage-type water heaters. It is worth noting that gas boiler usually made of steel and additionally covered with a layer of titanium enamel, which allows both to increase the reliability of the water heater and reduce heat loss.

Water heaters with indirect heating. They carry out heating of water by means of the coil installed inside. It is noted that these models heat water faster than all previous ones. But usually they are quite large and have big weight, but able to heat a large number of water (150-500 liters). Such volumetric models are not recommended to be fixed to the wall, but placed on the floor. The floor water heater has a very durable coating that increases its service life.

Among other types of Ariston boilers, it is worth noting flat devices. These compact models have minimal dimensions, they can be placed anywhere. Despite their small size, these boilers are quite powerful. This option organically fits into the room of any size and does not take up much space. And also the manufacturer offers customers rather unusual boilers that can be positioned horizontally. Horizontal models can be placed in a specially designated niche, thereby completely hiding it, which allows for even greater savings in usable space.

Popular Models

It is worth highlighting some of the most common models of Ariston boilers.

Ariston Velis Inox. This model has horizontal and vertical variations. Stylish design and a flat body make the boiler a rather attractive technical device that does not take up extra space.

Ariston ABS VLS. This option is almost completely automatic. Installed in the device various systems, which monitor the temperature and protect the heating elements from overheating.

Ariston ABS PRO. This type of water heater is cylindrical in shape, which allows you to place it in the corner of the room. This version of the boiler is one of the most budgetary.

How to connect?

Usually, the installation and connection of Ariston 50 liter boilers does not cause great difficulties. Each device is accompanied by an instruction manual. Therefore, installing a boiler is a simple matter and can be done with your own hands.

Installation of a mounted boiler is carried out as follows:

measurements must be taken on the wall, including determining the height of the unit;
then a pair of holes should be made with a puncher, which should be approximately 10 cm in depth;
for fastening the boiler, strong anchors are used that can withstand the heavy weight of the structure;
then the boiler is simply hung on the anchor with a special mounting plate, which is located behind the body.

One of the main points when installing a boiler is to correctly connect and carry out the first start of the device, using rules such as:

first you need to open the valve to supply cold water to the boiler;
then open the mixer, from which hot water; most likely, at the first start it will produce loud and intermittent sounds, but do not be afraid - this is normal for the first inclusion;
then you need to wait a bit until the boiler carries out a set of cold water to heat it;
after filling the boiler and heating the liquid, the water from the tap must flow stably; it is advisable not to immediately set a large temperature regime;
After the first start, the water temperature can be easily adjusted using simple commands on the water heater.

Faults

Even the most reliable equipment is not immune from accidental breakdowns. No matter how high the characteristics of the device, it can still fail. Various factors can influence this. Water heaters are usually characterized by breakdowns of water heating elements and thermostats. In order to avoid damage to the heating elements, it is recommended to carry out preventive maintenance and cleaning of the heating elements at least once a year. A long period of water heating, extraneous sounds during boiler operation, or more frequent spontaneous shutdowns can serve as an indicator of a malfunction. Boiler repair can be done independently; To do this, you need to disassemble the unit and determine the location of the breakdown.

In order to eliminate the malfunction with your own hands, you must follow certain steps.

To begin with, it is worth disconnecting the device from the mains, and then completely drain the water from it. To do this, you can use a hose that connects to a special hole for discharging water.
Shut off the flow of fluid into the boiler. After draining the water, you can begin to inspect the parts of the water heater.
Often breakdowns occur precisely in electric heaters, so you should immediately inspect the heating element (heater).
With prolonged use, any heating element is covered with scale. Therefore, it should be carefully removed, while you can use special tools.
If replacement of any components is necessary, then it is necessary to purchase only original parts by contacting the official manufacturer.

In some cases, a water heater tank may leak. In this case, you need to carefully examine the body of the product. It is possible that the problem lies in a leaky gasket, which should simply be replaced with a new one. But if the heater tank is leaking due to a crack or chip, then it is unlikely that it will be possible to eliminate this malfunction by independent forces. You can try to use the soldering method, but this is unlikely to help on long time. If the housing is damaged, corrosion in the heater begins to occur faster, and heat loss begins to increase.

Therefore, the installation of the heater should be carried out very carefully so as not to accidentally damage the housing. If such a problem still arose, then the best solution would be to contact the service center.

After analyzing customer reviews on the use of Ariston boilers, it should be noted that most of the owners are satisfied with the purchase, because the operation of such a water heater does not cause serious complaints. Buyers appreciated the stylish appearance, compactness and simplicity in management of a water heater. They were also separately noted low level heat loss, low electricity consumption during boiler operation. In general, the owners of Ariston boilers noted good value for money, as well as professional service in specialized services.

As negative points, periodic breakdowns of the water heating element were noted. Usually manufacturer Ariston gives a guarantee for the heating element up to one year. Some owners of boilers have had breakdowns before. But the performance of this element depends on many factors - frequency of use, water hardness and others. And also among the negative aspects, it is worth noting the lack of elements for mounting some wall-mounted boilers in the kit. These brackets must be purchased separately.