How to wash the floor in the bath for disinfection. Do-it-yourself soot cleaning in the bath: effective ways to deal with pollution

Before you disinfect a bath, you need to competently approach the issue of choosing a product and familiarize yourself with the rules for disinfection. There are a lot of antiseptics intended exclusively for washing such premises, but they must meet all safety and efficiency requirements.

How to disinfect a bath and why you need it

Sponges quickly become dirty during the process of cleaning the bath, so it is better to purchase several pieces at once.

Strict hygiene requirements are due to too high humidity, temperature fluctuations in the room, as well as the risk of visiting the bath for people with certain diseases. In such conditions, pathogenic microflora is very actively multiplying and spreading.

Necessary tools and materials

One of the best options for the disinfection of the bath is considered to be GOODHIM T150

Thanks to well-organized disinfection measures in an extremely hot and humid steam room, it is possible to preserve the finish with natural materials, minimize the risk of mold and unpleasant odors.

Necessary materials and means:

• a device for lifting wooden ladders and dismantling ceiling screens;
• hard brushes;
• sponges or washcloths on the handle;
• a container with boiling water;
• detergent for plates;
• antiseptic composition;
• sharpened cycle and skin P-100 or P-120;
• chlorine disinfectant;
• chimney cleaners;
• natural oils for impregnation;
• floor cloths and mops.

Step-by-step instruction

Do not use abrasive powders to clean the bath, as they spoil the structure of the wood surface

There are several main stages of bath disinfection, which are mandatory when caring for washing and steam rooms:

1. First, I raise the wooden ladders, remove the ceiling screens and wipe the floors.
2. Then the shelves are cleaned with sandpaper, washed with a washcloth on the handle or a stiff brush, previously soaked in boiling water. You can use special equipment and antiseptic formulations for this purpose.
3. Remove debris and leaves from the drain. The stones in the heater should be carefully cleaned of plaque or replaced with new, pre-washed ones.
4. After wet cleaning, the room is ventilated for several hours, and then the shelves and other wooden surfaces are impregnated with natural oil.

It is very important to thoroughly clean the chimney every year, which will prevent the risk of soot igniting inside the chimney, as well as to audit utilities.

General cleaning of the bath is necessary after each use. But it is disinfection that provides a deeper and more thorough cleaning of all surfaces.

A wooden bathhouse made of logs or timber is a great place for country house. Wood is distinguished by high thermal insulation properties, environmental friendliness and naturalness, safety. It does not heat up and does not burn the skin even at the strongest temperatures.

At the same time, the tree looks aesthetically pleasing and harmonious, fits into the environment. That's why wooden materials choose for the construction of a bath or sauna. However, natural raw materials are subject to negative influence humidity and insects. In addition, wood burns very quickly.

To protect wooden materials and extend the operational life of the building, the bath is processed. Today, there are many options and means that prevent the spread of fire on the surface in the event of a fire, rotting and destruction of wood, mold, fading and loss of physical properties. Let's look at how and how to process the bath from the inside.

How to choose the right tool

Natural wax, hemp and linseed oil- traditional materials for processing, which have not lost their relevance even now. It is safe and effective means. Today, manufacturers offer a lot modern means, which cover the walls in the bath and houses made of logs or timber. Experts advise choosing Finnish and Russian brands.

Choose products in such a way as to preserve the environmental friendliness of the building and emphasize the aesthetic interior of a log or timber bath. For a bath, especially for a steam room, you cannot use standard varnish or paint for wood, as they do not tolerate high temperatures. When heated, such agents will release bad smell and harmful toxic substances. In addition, with this treatment, the tree will not “breathe”, but will only absorb moisture and deteriorate.

Water and wax-based varnishes, as well as acrylic varnishes, are considered safe means for bath treatment. It can be colorless and colored products, with a matte or glossy sheen. For a steam room, it is better to choose a colorless varnish, and for a shower or rest room, you can take a product with a sheen or shade.

The vapor permeability of the varnish must be at least 50%. This indicator reflects the ability of water vapor to pass through the surface of the varnish film. Along with the steam, the smell of wood also passes. At the same time, the coating protects against moisture, which is not absorbed into the wood, but rolls down the wall onto the floor. As a result, the sauna atmosphere does not suffer, and the wood does not collect dirt and does not darken.

For the steam room, choose specialized odorless products. They consist of resistant components that do not break down under the influence of high temperatures. Classic antiseptics and varnishes are not retained in wood fibers, soften and become sticky at temperatures above 100 degrees Celsius. In addition, this process is accompanied by the release of harmful compounds and unpleasant odors into the air. Compositions for steam rooms are designed with these factors in mind, they are safe and environmentally friendly.

How to cover the walls and floor in the bath

Wooden walls in the steam room and washing room are covered with acrylic varnish or oil. The steam room is painted in one layer, the washing or shower room is covered with two or three layers. By suitable means in this case, impregnations such as "Supi Saunasuoja" (Tikkurila) and "Pinotex Lacker Sauna" (Akzo Nobel) are used.

Walls in dry rooms, for example, in a rest room, are recommended to be varnished or treated with impregnation for the interior. These waterborne coatings are odorless. In the MariSrub catalog you will find a wide selection of bath projects, including those with rest rooms, with a second or attic floor, as well as compact one-story buildings.

The floor inside the bath is least exposed to high temperatures, as hot air rises. However, the tree is greatest influence water as it flows down. The emphasis in this case is on protection against decay in a humid environment.

The floor logs are impregnated with a primer containing a powerful antiseptic, or varnished, which completely excludes the penetration of water into the wood. For this, a mold remedy, antiseptic "Pinotex Impra" (Akzo Nobel) is suitable. It gives the effect of preserving wood. The green color of this impregnation will not be visible under the finished floor, but the coating will provide long-term protection. To preserve naturalness, floor boards should be treated with shelf oil without the use of a primer.

In the rest room, locker room and other dry rooms, the floor is covered parquet varnish. In the steam room and sink, the varnish is diluted in a 1: 1 ratio with a suitable thinner and the floor boards are impregnated. Apply two layers. After that, the bath is heated to a high temperature and the rapid polymerization of the coating is achieved. After airing and reheating, the bath is ready for use for its intended purpose.

How to cover other elements

It is very important to process benches, shelves and other pieces of furniture in the bath. This will increase the service life of products and prevent burns on the human body as a result of contact with hot surfaces. Water should not be absorbed into the wood, and at the same time, a varnish film is not needed on the surface of objects, which, when heated, leads to burning of the skin. Such a coating is given by special oils for shelves in saunas, including Supi Laudesuoja (Tikkurila) or Sauna Oil (Eskaro).

Lacquer, oil or other agent is applied in several layers using a roller. Difficult areas in the corners and between the crowns are treated with a brush. Each new layer is applied only after the previous one has completely dried! When using oil, excess product is removed before drying. Such processing should be carried out every 4-10 years, depending on the type of materials and the quality of the work. To get a long-term and reliable result, contact the professionals!

The masters of "MariSrub" will select high-quality and reliable impregnations, quickly and reliably process the bath. We provide a full range of services. It includes the design and construction of a bathhouse or a house with a foundation and a roof, the manufacture of lumber for the project, installation and connection engineering networks, complex finishing. We offer thermal insulation and waterproofing of baths, protective treatment materials in several stages! We guarantee high quality of work and strict adherence to deadlines.

Periodically, the question arises of how to clean the bath. Sooty ceiling, dirty shelves and floors can spoil the pleasure of taking hygiene procedures.

Fundamental rules

How to clean the soot in the bath? There are certain rules for this. For example, wooden surfaces covered with a layer of soot cannot be wetted.

Wood is a hygroscopic material that quickly absorbs moisture. Together with water into the structure wooden elements everything that has settled on the surface is absorbed - soot, soot, bodily secretions, etc. After the dirt has been absorbed into the surface of the wood, it will be almost impossible to clean the shelves in the bath, walls, floor or ceiling.

Therefore, when deciding how to clean soot in a bath from walls or floors, you should categorically refuse to use such substances and materials as:

• laundry soap;
• water;
• sponges;
• spray guns.

All of the above products can only be used for final cleaning. wooden surfaces when the soot has already been cleaned dry.

All work on cleaning the bath from soot and soot must be carried out using special protective equipment:

• blind goggles;
• respirator;
• thick rubber gloves.

All this will help prevent the penetration of combustion products into the respiratory tract.

Wall and ceiling cleaning

To solve the problem of how to clean the soot in the bath, they begin with a vacuum cleaner. To do this, you need to walk them on wooden surfaces. Next, you need to carefully sweep the soot and soot from the walls and ceiling with a broom.

Prepared surfaces should be cleaned with sponges with special impregnation. They are sold in hardware stores. During the manufacturing process, such sponges are impregnated special formulations destroying soot and soot.

Sponges get dirty quickly, so you need to purchase several of them at once. You can extend the period of use by cutting off the soiled layer of the sponge.
When soot and soot are completely removed, you can clean the surfaces of walls, floors and ceilings with aqueous solutions of detergents.

Abrasive powders should not be used. They spoil the structure of wooden surfaces.

On a note! Degreasing powders and/or gels are preferred. They are added to hot water.

To clean hard-to-reach areas, it is better to use a mop with a long handle.

Surfaces are washed 2-3 times. In this case, the water must be changed periodically, adding a new portion to it. detergent.

When the question of how to clean the lining in the bath from soot is resolved, you need to wash off the washing solution clean water. For this, it is better to use running water. It is better to serve it from a hose under a little pressure.

At the end of the process, the washed surfaces are wiped dry with a clean soft cloth. You can use an old bath towel. From a large number moisture or with poor thermal insulation, the lining may turn black. In this case, the answer to the question of how to clean the lining in the bath will be a grinder, but this is if the darkening has affected only the surface layer of the wood.

To clean the walls lined with clapboard, you will need an angle grinder with a power of not more than 1 kW and a petal circle with a diameter of 125 mm (grain size not more than 40 units). The lining is sanded in such a way as to remove the darkened layer to a depth of about 3 mm.

If the blackness has absorbed to a great depth, the lining can be painted. But not in a steam room. Here paintwork is not used at all. You can replace the darkened lining partially or completely with new material.

Impregnating compositions for bleaching darkened wood, prepared on the basis of chlorine, are not recommended, since the carbon particles that determine dark color walls, practically do not discolor compositions containing active chlorine.

Unaesthetic dark spots appear on the surface of the bath logs from the outside over time, which spoil the appearance of the building.

Liquid bleach can be used to remove these stains. It is applied to the surface, previously cleaned of dust and dirt. For work, brushes with artificial bristles are used, which must be changed periodically, because the cleaning composition corrodes them. Before applying, you need to check its effect in an inconspicuous place.

The agent is carefully distributed over the entire surface and aged for some time according to the instructions on the package. Then you need to rinse the surface with running water from a hose. Next, the bath is ventilated to remove the strong smell of bleaching agents.

When blackening penetrates to a great depth, the logs can be sanded with a grinder. At the same time, safety precautions must be observed.

To clean the shelves in the bath, you can use a car wash. Water is supplied through it in a mixture with air and under high pressure. This makes it easy to remove upper layer from the darkened tree. In this way, you can also clean the floors, walls and even the ceiling in the bath.

To thoroughly clean the floor in the bath, you can use a planer, best with electric drive. Previously, the floorboards must be carefully removed and dried thoroughly, then treated with a planer. In this case, the top layer of wood on each side is removed to a depth of 5 to 10 mm.

As a result of this cleaning, sharp edges often appear on the floorboards. You can remove them with a belt or vibration grinder. You can also use these devices to clean darkened wood instead of a planer.

If the darkened layer of wood is thin, you can simply sand the surfaces sandpaper. An electric drill with a special nozzle will help facilitate the process. You can work only with absolutely dry surfaces.

This method will help you get into corners and other hard-to-reach places. It is not necessary to remove individual elements.

Such treatment is often recommended when answering the question of how to clean aspen seats and other wooden surfaces in the bath. After processing and polishing with sandpaper they will be not only clean, but absolutely smooth.

Why does the chimney get dirty

How to clean the chimney in the bath depends on the nature of the pollution. With use, types of clogging may occur, such as:

• soot and soot, which accumulates very quickly when burning household waste;
• condensate, which is formed during irregular use of the bath;
• foreign objects accidentally introduced into chimney.

All of these types of pollution ultimately impede the free circulation of air and the exit of smoke through the chimney. It can cause poisoning carbon monoxide. A condensate is a weakly concentrated acid solution. Under its influence, the chimney masonry begins to collapse from resinous deposits.

With the constant use of the bath, it is necessary to draw up a schedule, determine in advance when and how to clean the pipe in the bath. Regular carrying out of such work will save the chimney and stove and allow you to use the bath without problems.

How to clean a chimney

The chimney and pipe in the bath are cleaned with chemical and / or mechanically. Chimney cleaning liquids and/or powders can be purchased from a specialty store. Printed on the packaging detailed instructions. After reading it, it will become clear how to clean the pipe in the bath.

A good answer to the question of how to clean the soot in the bath that has accumulated in the chimney will be a “chimney sweep log”. It is impregnated with special chemicals. During combustion, smoke of a special composition is emitted in the furnace. As a result, the soot becomes soft and pliable. After 2 or 3 days, it can be removed with brushes without much difficulty.

For mechanical cleaning of the chimney, you will need tools and devices such as:

• rope and/or rope;
• weight (ball);
• ruff brush (preferably on a thin metal cable).

First you need to check the safety of the structure. Then you need to remove objects that accidentally fell into them from the pipe and chimney. For this, a brush-ruff is used, selected according to the size and shape of the pipe.

Facilitate cleaning work with a special brush modern design. It comes with a multi-piece handle. This allows you to adjust the length of the brush as needed. Any brush during cleaning works it is necessary to move inside the pipe, gradually moving it lower and lower.

Such work must be performed in a special set of clothing, which must include:

• overalls or suit;
• respirator;
• gloves;
• protective glasses.

If the chimney is slightly dirty, you can invite a specialist. He will clean it with a special high-powered vacuum cleaner. This will remove soot from the chimney through the opening of the firebox. Usage special means will solve the question of how to clean the chimney from pollution, and how to clean the pipe from soot in the bath.

Tank cleaning

Due to the hardness of tap water, the question periodically arises of how to clean the tank in the bath from scale, which settles on the walls and bottom. Since scale is formed from lime deposits, it must be cleaned with acid.

Acid can only be used of organic origin. For example, lemon or vinegar. Any inorganic acid is not safe for the metal from which the tank is made. It should be remembered that the amount of acid used to clean the tank should approximately correspond in weight to the amount of lime deposits on the walls of the heating tank.

On a note! Installing a special filter on the inlet will help prevent the formation of a large amount of scale.

The water passing through it will be purified from a significant amount of impurities. This will greatly reduce the level of scale formation.

Cleanliness in the steam room

The steam room in the bath requires special attention. Indeed, when using brooms, particles of plant pigment from stems and / or leaves are absorbed into wooden shelves and walls along with moisture. Therefore, the question inevitably arises of how to clean the steam room in the bath to give it a fresh and pleasant look.

The problem of how to clean the lime lining in the bath, especially in the steam room, can be solved in different ways. In case of slight darkening of the wood, special liquid detergents and / or paraffin oil can be used.

The cleaning liquid is applied to the darkened surfaces manually using a piece of foam rubber or an ordinary sponge. The detergent must first be diluted with water. How to do this is detailed in the instructions.

Paraffin oil is applied little by little to pre-dried surfaces with a dry sponge. In this way, you can not only clean the lining in the steam room, but also give the wood water-repellent properties. It will protect wood trim and various objects from strong and fast pollution.

Bath water purification

The necessary amount of water for hygiene procedures is often provided by drawing water from a nearby reservoir, well or well. Before use, it is necessary to thoroughly clean the bath water from various impurities, silt, sand, small pebbles.

The main methods of water purification are filtration and settling. A special water filter can be purchased at the store or made by yourself. To do this, you can use a fine mesh.

For settling, water is poured into a large tank about a day before the intended use. During this time, all impurities will gradually settle to the bottom of the tank. From above you can take clean water suitable for hygienic procedures.

The main rule: settled water should be taken from above, trying not to raise the sediment. Until the end of the water is not used. It is better to pour the remains into the drainage well along with the sediment. Therefore, it is necessary to prepare water with a margin.

Proper maintenance of the bath

To prevent strong pollution and the appearance of fungus, mold, woodworm, cleanliness in the bath must be maintained constantly. It is advisable to periodically treat internal surfaces with antiseptics to protect against microorganisms.

To prevent rotting wood flooring it is necessary to apply special compounds to walls, shelves, etc. All wood surfaces should be inspected periodically. Elements affected by decay must be removed partially or completely.

After each use, the bath must be ventilated to dry the interior. Immediately after taking bath procedures, you need to clean up. This will remove all stains from internal surfaces before they soak into the wood.

On a note! Important point— removal of leaves and small particles of the used broom from wooden surfaces.

They are removed with a special brush, sponge or cloth. Then the shelves and other surfaces need to be washed warm water. This will help remove sweat, detergents, etc.

The remaining water on the floor must be carefully adjusted to the drain holes. When cleaning, pay special attention to the space under the shelves.

To prevent cockroaches or mice from starting, all leftover food from the rest room must be immediately removed and the garbage taken out. Bath accessories should be dried and laid out in storage places. The final stage - wet cleaning all sections of the bath. General cleaning is also required from time to time. Correct content baths will keep attractive appearance and cleanliness of the internal space, as well as the integrity of all coatings.

When I was faced with the task of cleaning the sauna, I did not immediately grab the rag, but consulted with sauna owners and professional cleaners, and then chose the technology, tools and detergents that seemed acceptable to me in order to clean the sauna cleanly and quickly.

Here is this sauna soap, periodically bathing in the lake, so as not to overwork. So, to wash the sauna, first of all, we need a special mop on a telescopic handle, as well as other tools that I show below.



For washing the sauna, the only new tool for us will be this type of hand brush. There is also a brush on the side for washing clogged cracks.


With this manual brush, we clean only the seats and backrests with the sauna detergent, as they are especially dirty from human sweat and grease. We do everything else with already known devices on a telescopic handle, and do not jump on soapy stools at the risk of our lives.

But we have already seen this brush with a hard sponge on a telescopic handle here:







But it turns out that if you use a sauna product, this brush can also be used to clean wooden surfaces of walls and ceilings!

This is how dirty the tiles in the shower are wood sauna if not washed. And such a tile without a brush with a hard surface, as for a tiled floor, cannot be washed clean with just a terry cloth.

We talked with you about washing technology tiled walls and bathroom ceilings recently:



So in this post, only washing is new for us. wooden ceilings and walls.

And we have already seen such a rag with a nozzle for our light telescopic handle here:





And now we wash off with a wet rag on an ordinary brush on the same stick the soapy solution with clean water.


A rectangular bucket is very convenient for rinsing a rag and squeezing out water by simply running your hand over a terry cloth, so do not be lazy and change the water more often.


Now we wipe exactly the same, but with a dry cloth in stock, all surfaces. It is better to have several such rags in the household.

The windows were washed using the technology already described earlier:


after winter.

The fact is that I never washed it, but simply rinsed the surface with water, so I had to spend so much work.

And you can read here.

This is how the sauna brushes in the store look like.


Now we know which brushes we need to choose if we need to clean the sauna and how to use them in order to do it quickly and efficiently.
I don’t have a personal sauna, and the sauna in the ten-apartment building where I live is cleaned by a professional cleaner who is hired by the house committee. I cleaned the same sauna for a friend, in whose lakeside house we like to spend weekends with friends and relatives. It seems to me that kindness should be reciprocated with kindness. The friend was very happy and grateful!
And how and with what do you wash the sauna or bath, friends?

A wooden frame retains its operational qualities for a long time, if the bars are protected in a timely manner from adverse factors. Consider the main causes of damage to the walls of the bath and ways to protect the building.

Appointment of protective materials for a wooden bath

Modern preparations are able to protect the log cabin of the bath from all kinds of natural and physical influences:

1. Defence from ultraviolet radiation . Always protect the tree from the sun's ultraviolet radiation. In logs, the sun's rays burn out natural resins, destroy the structure of wood. The material ages, becomes gray. To process the log cabin of the bath, use compounds that create an ultraviolet filter. Containers with such impregnation are marked with the “UV” icon.
2. Fire protection impregnation. To prevent the wooden structure from burning, the logs are impregnated with special substances - flame retardants. After processing, the wood will not catch fire from a cigarette butt or a spark. Cans with fire retardants are marked with the image of fire.
3. Moisture protection. Water is considered the main enemy of wood. Under the influence of water or snow, the wood rots, the lower parts of the walls are especially affected. To protect the logs, they are impregnated with special compounds that protect the walls for 10 years.
4. Antiseptic impregnation. Wood can be destroyed molds, mosses and other microorganisms. It is very difficult to remove fungi, and they will ruin the appearance of the log forever. Microorganisms are disinfected with antiseptic impregnations. Well recommended products containing beeswax.
5. Insect protection. Wood beetles, bark beetles and weevils are planted in logs, which can turn wooden structure into dust. Biocides are used to kill insects. The tool can be recognized by the image of a beetle on the label.

Types of protective coatings for a wooden bath

The means intended for impregnation of the log cabin of the bath are quite diverse. They are divided into preparations for internal and external use. Let's take a closer look at their features.

Means for the internal processing of a wooden bath

Preparations for internal walls recognize by the inscription "For the sauna." Quality products can be bought in the company store.

Consider what to process wooden bath inside:

• The walls of the log house in the steam room and washing room are treated with special natural-based substances without artificial additives that do not emit toxic fumes at high temperature and humidity. Such drugs belong to the highest degree of environmental safety.
• For internal works use Teknowax 1160 - a special bath wax. The substance is odorless, without toxic elements. After application, it forms a smooth film on the wall, impervious to liquids and vapors and withstands high temperatures. They produce two types of wax for a bath - transparent and whitish. Transparent preserves the texture of wood. White wax visually expands the room. The tool can be used to cover the walls in the steam room and washing and in other areas of the bath.
• To process the log house in the dressing room and the rest room, you can use harmless products that do not cause allergic reactions. These products include Teknocoat Aqua 2550. This is a water-borne acrylic varnish that forms a protective film on the wall. The film is elastic, it washes well.

Means for external processing of a wooden bath

The coatings used to protect the bath from the outside are divided into impregnations and varnishes.

Let's find out how to process a wooden bath from the outside:

1. Impregnations are able to protect the tree from ultraviolet radiation, but cannot withstand precipitation. Water washes away protective substances from wood, the sun burns bald spots on it, as a result, the appearance worsens, the logs quickly deteriorate. Impregnation protects wood for 5 years. Therefore, it is necessary to re-coat the walls with protective substances.
2. When the walls are varnished, an indelible film remains on the wood, protecting the building from moisture and ultraviolet radiation. Before treating a wooden bath with varnish, take an interest in the properties protective film, which he creates. If it is too rigid, it can tear and crumble when the structure shrinks or the natural expansion of the wood. For outdoor use, purchase varnishes that create an elastic film. Therefore, it is not recommended to cover the outside of the bathhouse with yacht varnish.
3. For outdoor use, it is recommended to use Aquatop 2920-04 varnish, which creates an elastic coating. The protection will last 15 years.
4. Also, high-quality protective materials for wooden exterior walls are produced by well-known foreign companies Tikkurila, Pinotex, Remmers.
5. From domestic products, you can offer products from manufacturers Senezh, Aquatex, Rogneda.
6. You can also use the old means to protect the log cabins. The most famous are drying oil from vegetable oils, tar and resin from charcoal. True, the appearance of the building will deteriorate a little.
7. Instead of varnish, the walls of the bath can be painted on the outside. The paint is chosen according to a similar principle - to retain water and ultraviolet light. Therefore, the darker the color, the better protection. Apply paint in several layers.

Types of antiseptics for a wooden bath

When buying an antiseptic, find out what type it belongs to:

• Washable antiseptic. It is made on the basis of metal salts. Salts are washed out with water, so they are used to treat the interior of the bath - the dressing room and the living room. Washable ones are not used to cover the outside of the bath, the walls of the steam room and the washing room.
• Hard-to-wash antiseptic. It is intended for processing of a felling outside. The composition of the substance includes oil and synthetics.
• Short term antiseptic. It is used to cover individual surfaces of logs during construction.

When choosing antiseptics, remember that high-quality antiseptics are expensive. Pay attention to the label: it should say that the substance protects against all biological threats - mold, fungus, decay, etc.

Features of applying protective coatings for a wooden bath

Work is carried out immediately after the walls are erected, before the caulking. If the procedure is delayed, cover the log house with a film to protect it from precipitation. Before impregnation, clean the walls of dust, you can use a vacuum cleaner. Check that they are dry. Apply to the log protective agent and brush over the surface. Let the impregnation dry and repeat the procedure.

The method of processing a wooden bath is chosen depending on the degree of readiness of the building. When the wall is ready, the product is applied with a brush or spray. Using a brush allows you to paint the entire structure without missing a single centimeter of uncoated. Often preparations are stained red or green color to control the quality of the coating. But the work with a brush is painstaking and lasts a long time. Spraying allows you to get the job done faster, but the quality of the coating is lower.

On an erected log house, no more than 50% of the wall surface can be processed - only what is visible. Therefore, builders begin to process logs even before they are laid. You can lower a whole log into the bathroom for a certain period of time, which guarantees quality coating the entire surface and impregnation of internal areas. To do this, you need a large container where you can put a whole log, and a significant amount of impregnation.

In addition, diffuse antiseptic treatment is used, in which the surface of the logs is covered with a powdery or pasty substance with disinfecting properties.

Impregnation is applied to the walls in the following order:

• Anti fungus and moisture protection.
• Fire retardant impregnation with antipyrine.

Features of protecting a wooden bath by applying special coatings, see the video: