Electric water heater Ariston instruction manual. Water heater Ariston: features of operation and self-repair

18.10.2019

Comfortable life modern man cannot be imagined without hot water. And public utilities are not very worried about its filing, especially in summer time. Therefore, everyone strives to independently take care of the well-being in their home. Nowadays, many people have begun to use water heaters. They are economical and practical. Ariston brand water heaters are considered the most popular today.

Peculiarities

The main feature of water heaters is a tank built inside, in which water keeps the temperature set by the program for quite a long time. This type of heater is suitable for people who often have problems with hot water. The most common is a water heater with a volume of eighty liters. It works on one heating element and has a power of 1.5 kW. Accordingly, he can heat water to a maximum temperature of seventy-five degrees in three hours. Such a heater will be enough for a family of three. The Ariston model, which has a capacity of 120 liters, has a power of 1.8 kW. As you can understand, the entire line is very economical, but at the same time not very fast.

But the regulator knob, located at the very bottom of the tank, is also not very conveniently placed. And even if the design has only five heating modes, you need to look down constantly in order to control the process of heating and cooling water.

Of course, outwardly such a water heater only benefits from this, but ease of use is much more important. By the way, it is worth noting that turning the boiler on and off is also done using the rotary knob. This approach to design leads to the fact that only a light indicator and a thermometer are visible to everyone. But, despite minor flaws, all Ariston equipment has many advantages. Water heaters are no exception to the rule.

Stylish design will complement any interior space.
Each model is created using new technologies.
Water heaters of this company have a long service life. This is achieved due to the fact that inner sides storage tank covered with a layer modern material protecting it from the appearance of rye and plaque.

Complemented with dividers that prevent mixing of cold and heated water.
Ariston water heater thanks to built-in control sensors temperature regime has protection against overheating. The guarantee of safe use is a protective device that can work in case of any voltage fluctuations. Even if there is no water in the system itself, then you should not worry that it will turn on by itself, because it has special protection.
The heaters of this company help to save gas and electricity consumption. This is facilitated by thermal insulation, which keeps water hot for a long time.
Many of the models are equipped with protection against the appearance of any bacteria. Thus, the water is already purified.

But when creating water heaters, it is impossible to do without drawbacks. They are few and the main problem is that some parts of the structure fail from time to time. Breaks down very often magnesium anode, and then the water heater needs to be handed over for repair. And it can also fail. safety valve. All this is quite expensive.

Kinds

Ariston products can be divided into the following types:

floor boiler;
condensing boiler;
boiler with indirect heating;
instantaneous gas-fired water heater;
gas storage water heater;
electric heater with a storage function.
a heater having a heat pump.

Each of the devices is equipped with heating elements, various accessories, and control devices. Each model of a water heater has technical characteristics.

ABS VIS EVO PW D

This water heater is electrically heated. It has tubular heater element, pressurized tank type, electronic control, vertical and horizontal installation as well as wall mounting.

Ariston Regent 80

ABS PRO ECO INOX PW 80 V

If we decipher the abbreviation, then ABS means that this is a device that turns off the storage water heater in cases where there are power surges. PRO means that the water heater has a cylindrical body intended for vertical installation.

ECO is a label that notifies that the inner walls of the tank have antibacterial protection, as well as the function of water purification from various chemical impurities.

INOX means that for interior decoration The flasks are made of stainless steel, this will give a guarantee for up to seven years. PW means that the water heater has an economical electric unit of one and a half kilowatts, and is also supplemented with another heating element for one kilowatt. This, of course, puts a large load on the power grid, but at the same time, 80 liters of water heats up much faster.

Water heater Ariston VELIS INOX

The design of this model consists of stainless steel elements. The power cord is equipped with a protection system. But also this model has a fuse that prevents the heater from starting when the container is empty. It's already pretty reliable protection from common breakdowns. The shape of the water heater is flat. The heating element is made of the highest quality copper. The power of such a model reaches 2.5 kilowatts, so the wiring must match.

Water heater Ariston ABC VELIS PW

This model has a disconnecting storage device, which allows you to leave the water heater unattended. And there is also an additional feature that provides antibacterial protection. Outside, the tank is protected by a layer of stainless steel.

Ariston PRO ECO INOX PW V SLIM

Such a water heater has a power of up to one and a half kilowatts. The body is covered with stainless steel. The diameter of this model is only 35.3 centimeters, and the inside of the tank is covered with an antibacterial protective layer. This water heater will not take up much space and save energy.

Ariston ABS PRO ECO INOX PW

This model has a rather narrow cylindrical shape, so the water heater can be easily installed anywhere. It is controlled electronically. On the one hand, this is very good, but on the other hand, if the system fails, you will have to reconfigure everything in a new way.

All its parts, both internal and external, are coated with stainless steel. Thanks to many positive qualities it has a long service life, with a warranty period of up to seven years.

Ariston ABS PRO R INOX

The water heater consists of a mechanical thermostat, in addition, it has a magnesium anode that protects it from different bacteria. The heating control is located outside, not inside. Pleasantly pleased that this is the most economical model.

Ariston ABS PRO ECO PW SLIM

This model has a very narrow shape of the water heater itself. Such a simple and concise design is complemented by all the necessary protective systems. It is also economical in terms of energy consumption.

Ariston ABS PRO ECO PW

This type of heater is perfect for both kitchen and bathroom. It has all the protection systems, its design includes an additional heating element, which allows you to quickly cope with water heating.

Ariston ABS PRO R SLIM

A rather convenient cylindrical shape allows you to install a water heater in any corner of the room. He is the most budget option and has a diameter of up to 350 millimeters. Heats up quickly, has all kinds of protection, it includes a safety valve.

Of all the proposed models from famous brand you can safely buy almost any. All of them please with their quality, and serve for a very long time.

Wiring diagram

Any water heater that seems, at first glance, simple, has a simple and internal structure. Its dimensions can be both cylindrical and flat. Any water heater consists of:

boiler, that is, an internal tank;
the body with which the boiler is framed;
A heating element that heats the water that entered the tank, there may even be two of them, which contributes to the rapid heating of the water;
a layer of thermal insulation located between the body and the boiler, allowing the water to remain warm for a long time;
branch pipe with a divider;
magnesium anode, which prevents the deposition of mineral salts on the walls inside the tank;
voltage indicator;
thermostat;
thermometer.

Terms of use

To produce correct installation water heater, you must strictly follow the instructions. Reading it will help not only to study all its subtleties, but also to extend its working condition.

Before starting work, you should first choose a place where the water heater will be installed. It should be located near the bath or shower so that the heat loss is not large.
Next, you will need to make sure that the tank is filled with water when it turns on and off. The first inclusion must necessarily occur with a full tank.
When the heater is already connected to the network, the temperature readings should be displayed on its control panel. The instructions say that if the numbers are flashing, this means that the water heater is still in the off state. To turn it on, you must press the on / off button, which is located in the upper left corner.
On the control panel there is a button that sets the power. It regulates the voltage strength from 1500 to 2500 watts.

The temperature can be adjusted using the button on which plus and minus are written.
After setting the program, the water heater remembers it and works in the already set mode. If the boiler was turned off, the settings are automatically reset.
If any batteries are damaged, they must be replaced. You need to buy them from the same manufacturer as the water heater.
Planning not to use the heater long time, especially in winter period, it must be prepared for "stagnation". To do this, drain the water, leaving it empty.
From time to time it is necessary to clean the inside of the water heater from dirt. To do this correctly, you need to have certain skills. Therefore, it is worth contacting specialists.

Connection work should also be entrusted to specialists. First you need to carefully inspect the safety valve. It must not have any flaws. If they are, it is necessary to replace the part that is damaged.
It is also worth checking if the grounding works.
At the end of the instructions, it talks about a very good feature that protects the water heater from bacteria. Since the hot environment is a great place for them to breed. When turned on, the heater will raise the temperature by more than 65 degrees, which will not allow bacteria to exist. This function must be enabled once a month, this will already be enough.

Possible malfunctions

When buying an Ariston water heater, you need to know which places are the most vulnerable. The first is a thermostat, sensor devices, heating elements, switches. But it is also very common to repair insulating gaskets and valves.

Careless handling of the water heater may damage the integrity of the tank. And it is repaired only in the service. To determine the malfunctions in the water heater, you need to understand if there are changes in its operation. It can be a strong hiss during operation. And also often the period of heating water is significantly increased. A sign of a breakdown may also be the fact that the device turns on and off more often or the lights flash frequently.

To prevent this from happening, you need to clean the heater from plaque every six months as a preventive measure, otherwise it will turn into a pebble.

In order not to contact the service center in case of a small breakdown, you can do the repair yourself. This is not so difficult to do. First you need to de-energize both the device and the entire room. Then you need to drain the water. This is done using a hose that has a diameter slightly smaller than the hole designed to drain the liquid. The drain hose should be placed directly into the toilet. Next, the cold water supply is turned off. Then you need to disconnect the hose from the valve with cold water.

This hose must be connected to a faucet and also lowered into the toilet. Next, disassemble the water heater and remove the heating element, the fastening of which is on a nut with a plate or washer. Having pulled out the heater, you need to very carefully examine those places where there is scale. Where it is available, it is necessary to clean it, but very carefully so as not to harm the tank. After the scale is removed, the tank must be poured clean water. If the heating element is in working condition, it can be cleaned in the same way. After that, in reverse order, all hoses and spare parts of the water heater must be reinstalled.

The most budgetary tool for cleaning scale is considered lemon acid to be diluted in water. It must be poured into the tank and left there for a day. Parts must only be replaced with original parts. This ensures stable operation of the water heater.

To decide on the choice of an Ariston water heater, you need to know what the “ideal” boiler should be, and look for exactly these functions and characteristics in the descriptions.

The water heater must have a magnesium anode, which will protect it from scale and prevent corrosion.
Equipment that has a vertical design is much cheaper than a horizontal version, which is important for those who have savings in the first place.
Those water heaters that are made of stainless steel or titanium will last the longest. However, their price is also higher.
It is necessary that there be a bypass valve, which is necessary to relieve excess pressure that occurs as a result of the difference in the thermal expansion coefficients of metal and water.

The Ariston water heater with a volume of 80 liters will allow you to comfortably equip Vacation home or an apartment. It is easy to use and gets mostly good feedback from buyers. In addition, you can connect it yourself if you carefully read the instructions. But, when installing a heater with your own hands, you need to remember that from correct installation largely depends on the further operation of the device. Therefore, it is better not to save on installation, and invite specialists. This will help extend the life of the heater, as well as save the owner's nerves.

GENERAL REQUIREMENTS

This manual is included with the water heater. Keep the instructions in an accessible place
in case of transfer of the device to another user and / or moving to another place of operation.

Please read this manual carefully. The manual contains the necessary information on measures

safety during installation, operation and maintenance of the water heater.

carried out

user.

Installation

equipment

fulfill

a qualified specialist in compliance with safety regulations.

for damage resulting from failure to follow the instructions in this manual.

All installation and maintenance work must be carried out by a qualified person

in accordance with applicable standards and regulations, as well as with the requirements of the manufacturer.

Operation incorrectly installed device may result in personal injury and property damage.

The manufacturer is not responsible for damage resulting from incorrect installation.

equipment.

Keep packaging materials (clips, plastic bags, styrofoam, etc.) out of the reach of

children place. Packaging material is harmful to health,

The appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental abilities or in their absence life experience or knowledge if they are not under control

or have not been instructed in the use of the appliance by a person responsible for their safety

Do not touch the appliance if you are barefoot or have wet hands and/or feet.

Repairs must be carried out by a qualified technician using spare parts

produced by the manufacturer. Failure to comply with this requirement will result in the manufacturer disclaiming
all warranties.

11. The hot water temperature is controlled by a thermostat, which acts as an overheating protection.

12. Wiring must be carried out in accordance with paragraph "Electrical connection".

It is strictly forbidden to modify or replace the safety valve with another that does not comply with

current requirements and standards, if it is not included in the kit,

14. Do not store flammable substances in close proximity to the equipment.

Symbols used in instruction text

Symbol

Meaning

Failure to follow these instructions can result in serious injury up to

fatality

Failure to comply with these requirements may result in property damage,

plants or animals

General requirements and rules for safe operation

GENERAL RULES FOR SAFE OPERATION

rule

Danger

Symbol

Do not open the body of the water heater.

Defeat electric shock. Receipt

o> ^ south when touching hot components.

Injury from touching sharp edges
and performances.

Do not turn on or turn off the water heater,

inserting or removing the mains plug from the socket.

Use a switch for this purpose.

Electric shock if
damage to the cable, plug or socket.

Do not operate the water heater with

damaged power cable.

Electric shock when touching wires with

damaged ichlatation, under voltage.

Do not place foreign objects on

water heater.

Injury caused by objects falling into

caused by vibrations in the water heater.

foreign objects due to vibrations.

Injury caused by falling device.

Do not step on the water heater.

Damage to the device or objects,

located under it, when falling
device.

Availability autonomous system water heating provides not only comfortable living, but also independence from the whims of utilities. The performance of such systems, their efficiency and safety depends on specifications boiler "Ariston", connection diagrams and quality of installation.

The key to a long and trouble-free service is compliance with all operating rules and timely Maintenance. Ignoring the requirements prescribed by the manufacturer can lead to premature failure of both individual parts of the boiler and the entire product as a whole. In addition, the possibility of electric shock increases many times over.

The instruction manual contains all the necessary information regarding installation, connection, conditions of use and maintenance intervals. storage water heater Ariston. In addition, the document includes a list of the most common problems and a method for fixing them yourself, however, for effective solution problems will require knowledge of the design and basic principles of operation of the product.

The device and principle of operation of the water heater "Ariston"

A modern Ariston boiler for 30, 50, 80 and 100 liters is a hermetic structure consisting of the following parts and assemblies:

storage tank:
Electric heating element (TENA);
Magnesium or zinc sacrificial electrode;
Tuning and control unit;
Casing.

The inner surface of the tank must undergo anti-corrosion treatment. Depending on the cost of the product, various modifications may have as anti-corrosion protection:

Titanium coating;
glass-porcelain coating;
A layer of heat-resistant enamel resistant to aggressive compounds.

Besides, expensive models water heaters from the premium manufacturer "Ariston" can have all-metal welded storage tanks made of alloyed stainless steel.

The air gap between the casing and the inner container is filled with a polymeric heat-insulating composition (most often, polyurethane foam). Thermal insulation allows you to noticeably slow down the cooling process, thereby reducing energy consumption.

Heating elements are divided into two main types: "wet" and "dry". Wet are called heating elements that come into direct contact with the heated liquid. In the process of interaction with the working environment, a persistent coating of insoluble scale is formed on the outer surface of the heating element, which prevents normal heat transfer. A zinc or magnesium anode is used to protect the heating elements and the inner surface of the tank from corrosion damage.

The functionality, informativeness and ergonomics of the water heater from the company "Ariston" largely depends on the design and design of the control unit and settings. There are two types of control mechanisms: electronic and mechanical. Digital systems has an attractive appearance and differs in accuracy of adjustment, however, it is extremely sensitive to voltage fluctuations.

The mechanical unit looks “simpler”, and the adjustment accuracy is not the same, however, the reliability of such devices fully compensates for these shortcomings. In addition, the price of models with electronic adjustment is much higher.

The casing of the unit can be made of both metal and polymer materials. The most common is the cylindrical shape, but models of other configurations are in demand.

How to choose the volume of the water heater

Boiler capacity is one of the main criteria to consider. Customer reviews and statistical analysis allowed to determine the required amount of hot water depending on the number of consumers.

For one person, a 30-liter Ariston heater is enough. If two people live in one apartment at the same time, Ariston for 50 liters will fully satisfy the need for hot water. A family of three or four people will need "Ariston" for 80 liters. If we are talking about providing a private cottage or a small restaurant, the best option would be "Ariston" for 100 liters or more.

Operating instructions for the water heater "Ariston"

The beginning of operation can be considered the installation and connection of the boiler to a centralized cold water supply system and electrical network. The quality of installation depends on the safety, efficiency and service life of the product. If, for one reason or another, the boiler is put into operation on its own, special attention should be paid to the points below.

It is necessary to start work on mounting and connecting an Ariston brand water heater by carefully studying the instructions attached to it.

Since the power consumed by the device is quite large, it is necessary to make sure that the characteristics of the electrical wiring used for connection fully correspond to the expected loads and has. The best option for connecting to the mains is a separate cable from the switch cabinet or shield.
Do not use components with visual defects, damaged threaded sections, etc. The safety valve included in the scope of delivery deserves special attention.
Since the mass of the product is quite large, and the temperature of the water contained in it can reach up to +75 0 С, the boiler must be fixed to the bearing surface on metal diameter not less than 10 mm. It is allowed to use plastic dowels of the same load capacity.
Installation of supply and discharge pipelines must be carried out in strict accordance with the diagram attached to the heater by the manufacturer.
The place of connection to the power supply must be reliably protected from condensate, dampness and direct contact with water.
You can connect Ariston to the power supply only after filling the storage tank with cold water, otherwise the water heater heater may fail.
If all the work is done correctly and the product is working properly, after switching on, the corresponding indicator should light up, indicating that the boiler is working.

Water heater Ariston: operation, maintenance and repair

To ensure efficient and safe work you must know and follow the basic rules for using the product.

It is forbidden to turn on the device until the storage tank is completely filled.
Mechanical or other damage to electrical cables is not allowed;
Before starting the operation of the Ariston water heater, make sure that the grounding is in good condition;
In the event of a malfunction, the unit should be immediately disconnected from the power supply, drain the water and contact the Ariston service center.

Even with proper operation, timely maintenance of the system is necessary to maintain operability. First of all, this is due to the low quality of the water supplied. Despite the presence of filters, a large number of chemical compounds and mechanical impurities that contribute to the formation of scale and other contaminants. Regular and internal surface of the drive will significantly increase the life of the boiler. Scheduled maintenance includes:

Preliminary draining of water from the storage tank;

Disconnection of plumbing fittings;

Dismantling the body of the water heater;

Cleaning the heating element and the inner surface of the tank without the use of particularly aggressive detergents, avoiding mechanical and abrasive effects as far as possible;

Assessing the condition of the magnesium anode and, if necessary, replacing it.

The conservation and subsequent activation of the boiler deserves special consideration.

How to turn on the Ariston water heater after winter: instruction manual

If the use of the device in the cold season is not planned, measures should be taken to preserve the system, and, above all, the water heater itself. For this you need:

Completely drain the water from the storage tank;
Disconnect the plumbing fittings from the inlet and outlet pipes;
Clean the heating element and inner surface tank;
Copiously lubricate the threaded surface of the nozzles with grease or other grease and wrap with rags or PVC film.

To turn on the Ariston heater after winter, you must:

Clean the pipes from grease residues;
Connect the device to the main pipelines;
Make sure that the grounding and electrical wiring are in good condition;
Fill storage tank cold water;
Turn on power.

Important! Connecting an empty storage heater to the mains is strictly prohibited!

Due to the simplicity of design, reliability and affordable price, Ariston for 30, 50, 80 and 100 liters is deservedly popular. Wide the lineup allows you to choose a model according to your needs and financial capabilities. However, we should not forget that only full compliance with the operating instructions and timely maintenance will ensure efficient work and prevent premature failure of the Ariston boiler.

Ariston water heaters are popular in the world market. This is due to the high quality of the products and the long service life, if the technical requirements both during the installation of the equipment and during its operation.

Popular models of Ariston water heaters.

Why Ariston water heaters are created

Ariston boilers are designed to heat and maintain desired temperature water. Equipment is needed if there are interruptions in the supply of hot water. Installation of equipment can be carried out in bathrooms (bath, toilet).

Models and displacement

Due to the popularity of products, the manufacturer produces a large number of models with different characteristics. Models with electric heating elements differ in volume and the presence of a storage tank, power, water temperature limit. The higher the power of the heating element, the higher Maximum temperature heating.

There is also a difference in dimensions, weight and installation methods (vertical, horizontal).

The list below shows the most popular Ariston brand models on the market - a water heater and its brief description:

ABS VLS (VELIS) EVO PW 50- electric storage water heater. Volume - 50 l, equipped with a quick heating function, an electronic thermometer to monitor the water temperature, a safety device to protect against switching on if the tank is empty.
NTS 80V 1.5K SU 3700366- electric storage water heater. Volume - 80 l. Equipped with an external temperature controller in the form of a round scale.
ABS VLS EVO INOX PW 80 D- electric storage water heater. Volume - 80 l. The tank consists of 2 40-liter compartments. It has the possibility of accelerated heating, in the presence of 2 heating elements.
ABS PRO R 100V- electric storage water heater. Volume — 100 l. The model is equipped with protection against overheating (ABS security system). Energy savings are ensured by polyurethane foam insulation. Vertical installation provided.
ABS ANDRIS LUX 30- electric storage water heater. Volume — 30 l. The model has a bottom water pipe connection. The tank is made of steel, the inner coating is Ag+.

There are also small models with tanks of 15 and 10 liters. All the mentioned products in Tyumen can be purchased at the QUANTA + online store.

Typical boiler diagram Ariston 50

Components of the electric storage water heater Ariston.

Electric storage water heater Ariston consists of:

outer case;
bracket;
internal tank;
hot water outlet;
magnesium anode;
cold water inlet;
heat insulator;
thermostat sleeves;
heating element (TEN);
flange;
thermostat;
power cable;
regulator knobs.

To connect the Ariston boiler correctly, you must follow the manufacturer's instructions.

First, the water heater is mounted on a wall or a supporting surface and a drain is provided from water pipe(cold water). It is most advantageous to install the device as close as possible to the source of water supply - this allows you to minimize heat loss.

If there is a collector in the system, a separate cold water supply pipe is transferred to the installation site of the water heater. In the absence of a collector, the nearest segment of the water pipe is cut, a standard tee is installed at the cut site.

The installation method of the tee depends on the material from which the pipes are made. On plastic fasteners is carried out using a special soldering iron, on metal - threaded.

A ball valve is installed on a separate section of the water supply system, designed to shut off the supply of cold water.

Scheme for connecting an electric storage water heater Ariston.

To connect the water heater to the water supply, you should:

Pay attention to the hot and cold water pipes - it is important not to confuse them. Installed on cold check valve, it can be included in the standard package. Hot water is connected via a pipe. First, a cold water pipe is mounted, then a hot one.
A special tape is wound on the threads as a sealant and sealant, this is recommended by the manufacturer.
A tee is installed on the cold water pipe, at the bottom of which there is a relief valve. A tap is attached to the side to completely drain the water from the tank in case of emergency possible under abnormal pressure or heat. A shut-off valve and an adapter are installed under the tee at a short distance. The next step is connecting to the water supply.
Connection to hot water is also made by installing a shut-off valve.
In the case of connecting different metals, adapters should be used.

The connection to the mains is carried out as follows:

AT switchboard a separate machine (RCD) is installed, it is connected to a central automatic fuse. A three-core cable is pulled from a separate RCD to the boiler, which is placed in an external cable channel (or a special gate is punched in the wall).
It is recommended to install a 16 A fuse as a switch, since the socket and plug are subject to heat and moisture. In addition, the cost of waterproof electrical equipment is higher than the cost of the machine. The "switch" is closed in a compact cabinet with a removable panel.
A separate RCD machine and a “switch” are connected by a wire.
A three-wire wire is connected to the heating element, for this the bottom panel is removed from the water heater.
Then the output of the machine is connected to the boiler.
The next step is to wire the ground, phase and zero lines to the appropriate connectors.

Scheme of connecting the Ariston water heater to the mains.

Before turning on the device, you must make sure there are no leaks and correct position flange (strictly in the middle). Then fill the tank with cold water and open the hot water faucet to release the air. After the air is released, the valve closes and a trial run is carried out.

How to identify a malfunction

For repair work the user needs to notice a malfunction in the operation of the water heater in time. Ariston boilers are often equipped with an electronic display on which messages appear in case of equipment failures.

Direct signs of a malfunction can be:

operation of the machine at the moment the boiler is turned on - this indicates a malfunction of the heating element;
heating water above the maximum allowable temperature - this indicates a failure of the thermostat;
heating water below the required indicators - this may indicate contamination of the heating element, the appearance of scale;
drips at the bottom of the tank and on its walls;
breakdown of the information board, which most often does not cause significant failures in the overall functionality of the device, but can reduce comfort during its use.

The Ariston water heater is represented by a fairly wide sanitary assortment and the corresponding standard model lines.

The products of this trademark has the following categories:

traditional boilers;
floor boilers;
condensing boilers;
floor boilers;
boilers with indirect heating;
instantaneous gas water heaters;
water heaters equipped with heat pumps;
storage water heaters on gas;

Each appliance is equipped with heating elements, control devices and additional accessories.

Why Ariston water heaters are created

Household appliances for heating water, which are powered by electricity, are most often used for the period when hot water is turned off. As a rule, they acquire compact models. When professionally installed, it provides a supply warm water for daily household needs: washing, cleaning or showering.

In private sectors, with all communications, they use gas and larger volumes with storage. In this case, household appliances of the most famous Italian company are used all year round.

How to turn on the water heater Ariston

Under no circumstances switch on an empty heater!

Most household appliances are characterized by the following instructions when first turned on:

Open the cold water supply valve (not to be confused with the safety valve);
Open the hot water tap or lever from the mixer connected to the water heater;
Wait a certain amount of time to collect water;
When the heater is filled, water should flow from the mixer;
Provide proper nutrition for the device;
At the first start-up, the temperature should be set in the middle position, over time, the liquid temperature level is adjusted to save and quickly heat up;
Electronic models Ariston is regulated by buttons for the required level of heating;

These steps must be performed by the installation wizard.

Due to inexperience, they forget to open the valve responsible for supplying hot water from the boiler. If it is not fixed in the desired position, then the heated water from the device will follow into the riser of the house.

Water heater repair Ariston

Ariston water heaters have vulnerable parts:

thermostat;
sensors;
switches;
heating elements.

Most often, valves and insulation gaskets are repaired. The integrity of the tank is violated less often. This failure occurs due to corrosion or careless handling. The tank needs to be repaired only in the service.

As an independent repair, timely preventive cleaning is implied. Every six months, it is recommended to clean the heater for the Ariston water heater.

How to determine the malfunction?

It's simple, with obvious changes in work:

Strange hissing during operation.
The standard heating period is extended.
Switching on and off noticeably increased.

Any high-quality Ariston device is easy to handle with self-repair. But it's better to follow this guide:

De-energize the room and the device.
Drain the water. Drainage must be provided by a hose with a diameter slightly smaller than the liquid discharge hole.
Put the drain hose into the toilet.
Shut off the cold water supply.
Disconnect the hose from the cold water valve.
Connect this hose to a faucet and lower it into the toilet.
Remove TEN. Its fastening is always on a nut with a washer or a plate.
Having pulled out the heating element, carefully examine all places with scale and try to remove everything without harm to the tank.
After removing the scale, pour clean water over the tank.
If the heater itself is in working condition, then you can clean it in the same way.
Install all hoses and parts of the heater in the same order.

A budgetary and optimal way to wash off scale is citric acid diluted in water. This solution is poured into the tank and left for 24 hours.

With an independent approach, it is possible and necessary to replace parts only with original ones. Spare parts for the Ariston water heater from the manufacturer guarantee the quality, the money invested in repairs and the stable operation of the devices.

Modern appliances for heating water are classified, first of all, by displacement. Selection also begins with the volume of the tank. Each of Ariston models designed for specific premises and the frequency of inclusion. What is the difference between the models?

Models and displacement

Line of models:

VELIS INOX.

Original Specs:

stainless elements, including tanks;
characteristic difference - universal (simple) installation;
flat shape;
Ariston water heater is available in 30, 50, 80 and 100 liters;
there is a protection system on the power cord;
fuse from starting with an empty container;
additional equipment is equipped with protection against freezing or overheating;
branded heating elements are made of high quality copper;
load distribution function due to flasks and two heating elements of 1 and 1.5 kW;
maximum power 2.5 kW.

ABS VLS INOX QH

Outwardly similar to VELIS INOX, but has differences:

Ariston water heater for 30, 50, 80 and 100 liters;
improved design solutions;
equipment with electronics for rapid heating, antibacterial water treatment (ECO), temperature measurement;
water is processed in two tanks; in rooms with a large area, an Ariston water heater of this model of 100 liters is recommended.

VELIS QH

It has external similarities with ABS VLS INOX QH and VELIS INOX.

Model differences:

super-fast heating;
ease of design and use;
LCD - display;
soft touch function (automatic saving);
water is heated in several stages;
internal tanks are covered with steel;
three heating elements (heating elements);
Ariston water heater for 30, 50, 80 and 100 liters.

ABC VELIS PW

Original Specs:

safety shutdown (ABS0);
bacterial protection (ECO);
the inner tank is covered by latest technology AG+;
special welding method during the assembly process;
two heating elements;
heating in two containers.

PRO ECO INOX PW V SLIM

Original Specs:

water pressure function;
stainless steel;
model SLIM, diameter is only 353 mm;
internal tank with a special antibacterial coating;
installed at points with cold water pressure, any level of pressure is suitable;
low power (up to 1.5 kW).

ABS PRO ECO INOX PW

Original Specs:

Ariston heaters for 50, 80 and 100 liters;
narrow cylindrical shape;
simple installation;
electronic control;
external and internal parts from stainless steel;
testing for 16 atmospheres;
7 years warranty.

ABS PRO R INOX

Original Specs:

mechanical thermostat;
Ariston heaters for 30, 50, 80 and 100 liters;
a magnesium anode was installed to protect against corrosion and scale concentration;
external heating control;
protection against water drops;
water resistance;
one of the most economical models.

ABS PRO ECO PW SLIM

Original Specs:

Ariston heaters for 30, 50, 65 and 80 liters;
narrow forms of a water heater;
economical energy consumption, the tank of the model was tested for strength under a pressure of 16 atmospheres, a good margin of safety;
equipped with all security systems.

ABS PRO ECO PW

Original Specs:

Ariston heaters for 50, 80, 100, 120, 150 liters;
suitable for kitchen sink, full-fledged home or cottage;
equipped with all protective security systems;
additional heating element.

ABS PRO R SLIM

Original Specs:

the convenient shape of the cylinder allows you to mount the heater in any corner of the room;
Ariston heaters for 30, 50, 65 and 80 liters;
"folk", budgetary and suitable in size water heater;
with a diameter of 35 centimeters;
fast heating;
the presence of a safety valve;
all water protection systems, switching on without water;
the price of an Ariston Water Heater of such a model of 80 liters is only 8800 rubles.

Original Specs:

instant heating;
practicality;
compactness;
affordable;
the possibility of horizontal and vertical suspension;

Typical instructions for a water heater Ariston 80 liters

Water heaters of this volume are necessary for daily use by the whole family. Presence of sensors and temperature level guarantees safe operation.

A complex and responsible event in the installation process is the wiring. Most often, the wires need to be lengthened, because the factory cable is not long enough.

For long-term use of the device, it is necessary to carry out installation according to all the rules or with the help of an experienced craftsman. To avoid breakdowns and other troubles, follow the rules of operation:

The first switching on and switching off is carried out with a filled tank.
If the batteries are damaged, be sure to replace the weak parts.
In a room with a minus temperature, it is necessary to drain the water from the heater.
Long periods of inactivity of the appliance without heating function should be carried out with a closed tap or valve supplying water. Also, heaters must be unplugged from the outlet.

Devices for high-quality water heating from Ariston are presented in user-friendly sizes, equipped with all kinds of engineering improvements and are available in all major retail chains. It is enough to choose the model you need for individual installation.