Do-it-yourself ottoman for the bedroom. Do-it-yourself ottoman: step-by-step instructions on how to make original and comfortable furniture

23.06.2020

Often the effect cosmetic repairs can be achieved, practically without resorting to it, by introducing new details into the interior of the home, be it a closet, couch or even stylish looking relatively small interior details.

An example of this is an originally made ottoman, made independently or bought in furniture store.

How to make an ottoman easily and without large material costs, with photos and instructions, will be discussed in this article.

Fabric ottoman

To make a fabric ottoman, you will need the following materials and tools:

pieces of fabric of various colors;
sewing machine;
thread, buttons and needle;
foam rubber or synthetic winterizer filler.

In order for the ottoman to retain its shape under loads and be elastic, a lot of filler will be needed.

Work begins with the manufacture of patterns. First, a circle of such a diameter is cut out of a suitable piece of thick cardboard, which should be the product in its final form.

The resulting circle is divided into 6-12 parts, depending on how many types of fabric are available and what the number of segments will be for a round ottoman. Then, with the help of these patterns, pieces of fabric are cut out with a small margin for stitching, and the same is done with the lining.

It turns out two bases - the upper and lower, which are also sewn together. It is important to leave one of the segments unsewn in order to be able to stuff.

The final stage of the process is the stuffing of the product with synthetic winterizer or foam rubber filler. When stuffing, you need to pay attention to the moment so that when you press hard, the ottoman does not deform.

After the end of the process, the remaining unsewn segments are sewn, and in the center, at the junction of the petals on both sides of the ottoman, they are sewn on a button.

Pouffe filled with polyethylene bottles

Usually plastic bottles are taken to the trash, but there is a better option - to use them as a filler. To work, you will need the following materials and tools:

several dozen plastic bottles;
adhesive tape, preferably wide;
lining made of synthetic winterizer or foam rubber;
thread, needle and buttons;
sufficient amount of fabric to make a cover.

First of all, a skeleton is constructed from bottles with tightly screwed caps, which is fastened with adhesive tape. If possible, the frame is given a rounded shape.

Then two circles of the corresponding diameter are cut out of cardboard. Also, with the help of adhesive tape, cardboard is attached to the bottles from above and below.

Two circles of the corresponding diameter are cut out of the foam rubber for the upper and lower sides, and a rectangle into which the frame is wrapped from the side. Fastening is carried out to the cardboard using a glue stapler or sewn on, foam rubber is placed on the glue from the side.

The matter remains small - you need to sew a cover of the appropriate shape and size for the resulting softened frame.

Thus, with minimal material costs it turns out quite a decent, soft ottoman with an original design.

Pouffe from a plastic bucket

If the household has a plastic bucket without a handle, and there are no ideas where to put it, you can use it as a frame for an ottoman. In addition to the bucket, you will need a hemp rope, a glue gun, cardboard, a large button, microfiber and a stapler.

The idea is this - the bucket is braided with a rope, which is immediately glued to its side surface. Further, according to the shape of the bottom of the bucket, a circle is cut out of cardboard; a circle is also made of fabric, somewhat larger in diameter.

In the center, the fabric and cardboard are connected with a button, which is wrapped with microfiber rolled into a tube, fixing it with a glue gun.

Wrapping is carried out to the edge of the cardboard, then the top layer of fabric is attached to its reverse side by means of a stapler. To complete the product, the lid and base are glued together. The cost of funds, as in previous cases, is minimal.

Photo instruction on how to make an ottoman with your own hands

An ottoman is certainly a necessary thing in the house. But there is no particular need to buy it, since it is really easy to make it yourself. For this procedure, it will be possible to use various home materials and some tools. To learn how to make a round ottoman with your own hands, it is worth considering some practical recommendations from experienced professionals, studying which you can come to the conclusion that anyone can do it.

The network has a huge number of options for how you can make a pouffe with your own hands. Thanks to independent action You can save a significant amount of money and use improvised materials. The most popular ways are as follows:

seat out plastic bottles;
ottoman from a bucket;
from a cable reel.

Pouffe from plastic bottles

The option of plastic bottles is quite popular, since almost every house has them, and problems with source material will not. In addition, the bottles are quite strong and durable. To make such an ottoman in the hallway, you will also need adhesive tape, foam rubber, thick cardboard or plywood and upholstery fabric.

It is important that the bottles are the same both in size and shape, and in density. Their number depends on how voluminous the pouf you want to make. But remember that the seat will be stronger, the larger the area of \u200b\u200bthe top.

Place the bottles upside down and tie them tightly with duct tape. According to the resulting diameter, cut out four identical circles from cardboard or plywood. Two will go to the lid, and two will go to the bottom. So the design will be stronger. They also need to be attached with tape. This is the preparation.

Bottles are connected to cartons with tape

Now you need to make it soft. To do this, cut a piece of foam rubber of the desired size and wrap the side of the ottoman. Cut out a circle for the top. Foam rubber can be replaced with synthetic winterizer. The thicker the layer, the better. Glue the material to the workpiece.

The surface of the resulting frame is covered with synthetic winterizer or foam rubber

The seat trim can be made of fabric, leatherette, decorated with ruffles and appliqué. A knitted cover will make the ottoman unique. Using your imagination, you can create what you like best.

Another option is 2 large 10-liter plastic bottles. At one (lower) you need to cut off the neck and insert another into it. Stitch exactly the same soft material and put on a cover.

Ottoman from a plastic bottle We cut one bottle and combine it with the second For the base and seat, cut out circles from chipboard
Foam rubber for our ottoman We fix the foam rubber on the seat We fix the foam rubber on the side surface
For the bottom, a leatherette circle is suitable. We make a cover from the material you like and pull it over the ottoman

From a bucket

Bucket ottoman

You can also make a pouffe with your own hands from inventory that is no longer used for its intended purpose. It can be, for example, an old leaking bucket. The principle is the same. Turn the bucket upside down, cover it on the sides with batting or synthetic winterizer.

Glue the foam to the sides

Place a suitable round model on top. Soft material can be glued on for a more secure hold.

Glue the foam to the lid

Remove the handles from the buckets in advance, otherwise they will interfere.

We sew a cover

Sew a cover from a pleasant to the touch material and put it on the seat.

We put on a cover

A similar design is obtained by using a cable reel. In a word, if you want to make a round original ottoman with your own hands, you can take any blank and cover it with soft material. A piece of furniture made in this way will not only free your house from trash, but also save money.

From chipboard and plywood

Cylindrical ottoman

And below is a step-by-step guide on how to make an ottoman from scratch, using only the right materials and your skills. Such a product will look beautiful and noble in a city apartment. So, you will need:

Chipboard about 18 mm thick;
plywood (3 mm);
wooden blocks for legs;
self-tapping screws;
synthetic winterizer;
upholstery fabric;
staples, glue and thread.

First you need to cut out two identical circles. They will serve as the base and top of the pouffe.

Cut out chipboard circles the right sizes and bar details

Then between them put the bars of the desired height and attach with self-tapping screws at the same distance.

We connect circles and beams with self-tapping screws into a frame

When the frame is ready, cut a sheet of plywood to sheathe the side of the product with it.

Along the perimeter on the frame we fix a chipboard sheet, making a wall

Using a stapler, nail the strip at the top and bottom to the chipboard.

Fully anchored wall

Now you can glue the workpiece with soft material. Upper layer must be thick in order to sit comfortably on the pouffe. 5 centimeters will be enough.

Fastening of foam rubber and synthetic winterizer

Sew a cover from any upholstery material. It can be eco-leather, dense fabric.

Finished case

You can attach it to the frame with staples or glue.

We put on a cover and fix it from below with a stapler or nails

If desired, make legs for the ottoman.

We fasten the legs

As you can see, making such uncomplicated home furniture is completely easy.

Ready product

To do this, you only need a little ingenuity, improvised materials and tools, and a suitable idea. Considering how much finished furniture costs in stores, you will understand how profitable it is to be able to do something with your own hands. In addition, you can be truly proud of your poufs, because you have invested in them not only work, but also your soul.

Sometimes you really want to update the interior, give it a new style, and additional pieces of furniture will become the most suitable assistants in this matter. And if it’s easier to buy a wardrobe or a sofa in a store, then making an ottoman with your own hands is very simple.

Ottomans came to us from the East many centuries ago, and immediately gained popularity. In the recent past, they occupied an important place in city apartments with small footage, since they simultaneously served as a table, an armchair, and a footstool.

Homemade ottomans have a lot of advantages compared to store-bought ones. You can choose the appropriate shape, size, color and type of material. In addition, in the manufacture of such an ottoman, you can use any means at hand, and such a piece of furniture will cost you almost free.

Soft ottomans: simple and easy from what is at hand

Taking up the manufacture of an ottoman, tune in to the fact that you can handle such a simple and easy job without any special worries, and we will help you practical advice and advice. You will need:

Sewing machine;
Textile;
stuffing material;
Paper to apply the pattern.

First, prepare a pattern using the diagram below. Lines B and C on it indicate the places where the paper is folded. It also shows how the template will look in expanded form.

1. Take the unfolded template and attach it to the fabric. You will need to cut 8 identical pieces of fabric. Not to spend money on new material, use old clothes.
2. On each blank, bend an acute corner inward by 5-6 cm and sew so that after assembling the pouffe, an octagonal hole remains in the upper part, into which the stuffing will be placed.
3. Stitch the blanks from the inside in pairs to each other (during cutting, do not forget to leave a seam allowance of 1 cm over the size of the pattern). Thus, you will get 4 parts from 2 blanks stitched together on one side.
4. Sew 2 pieces in the same way: these will be the two halves of your pouffe. Sew them together and turn the cover inside out.
5. Stuff the finished pouf cover with the selected material (it can even be scraps of fabric). Cut another piece to fit the remaining hole, finish the edges and sew by hand.

Tip: It is not necessary to use fabric of the same color for the ottoman. A multi-colored ottoman will enliven the interior, especially in a children's or teenage room.

Such an ottoman is very soft and light, small children will be happy to play with it, and you do not have to worry about their safety.

An even simpler scheme for making an ottoman

There is not always time and desire to mess around with patterns, so we offer you another, very simple option.

Cut out 2 circles from the fabric. Their diameter should be equal to the diameter of the top and bottom of the product. Don't forget to leave seam allowances!
Now cut out 2 rectangular pieces of the same size. Their width will be the height of the pouffe, and their length will be half the circumference of the upper and lower parts.
Sew the rectangular parts together across the width on one side to make a long ribbon. Baste one of the circles to it and stitch along the seam. Do the same with the second circle. If the seam is not even or neat enough, you can sheathe it with a decorative border.

Thus, you can quickly and easily make a pouf cover that is easy to fill with any suitable material. It remains only to sew a zipper into the unstitched edges of a rectangular tape.

In the same way, you can make a cube-shaped pouffe. The only difference is that the pieces need to be square, and for the sides you will need four pieces of fabric instead of two. Sew the details together, and in order to more clearly indicate the edges of the cube, use a canvas in a contrasting color. A denser fabric will give extra elasticity and help keep the shape.

Please note: a synthetic winterizer and foam rubber are perfect for stuffing such a pouffe. These materials do not deform and keep their shape perfectly.

Make a hole through which you will place the stuffing material from the bottom of the pouffe so that it is invisible. Optionally, you can stitch it tightly after the pouffe is stuffed, or sew in a zipper to be able to change the material if necessary.

We use improvised means: an ottoman made of plastic bottles

This option will allow you to significantly save on stuffing materials. The interior space of the ottoman is filled with plastic bottles. So, you will need to stock up on the following:

Plastic bottles of the same shape and volume;
Thick cardboard (use cardboard boxes, just make sure that they are not damaged);
or synthetic winterizer (you can also use insulation or several layers of dense fabric);
Scotch;
Glue;
Scissors.

Cut out two identical circles of the diameter you need from cardboard - these will be the top and bottom of the ottoman. Set the bottles on the bottom circle so that they fill the entire space and tie them tightly with tape. Cover with the top circle and rewind with tape so that all the parts are evenly and firmly connected to each other.

The base is ready, now we start finishing the ottoman.

From the insulation (foam rubber, synthetic winterizer), cut out two circles and a rectangle. Details should be slightly larger than the base elements, taking into account seam allowances. Connect them together and sew by hand with tight stitches.
Sew a cover for your ottoman according to the same principle as in the second paragraph of this article.
You can add an additional functional element in the form of a strap to the finished product. It will make it easier to carry and will surely appeal to children who will be happy to carry such an ottoman with them as a toy.
If you plan to make an ottoman that you will use yourself, take a denser fabric for the cover and insert a border along the seams. For a children's ottoman, you will need soft material with colorful colors. It is advisable to use a denser layer of foam rubber.

This ottoman is not only easy to perform. By making it yourself, you will save yourself from the need to recycle plastic bottles, and this is already a great reason to take part in the fight for a clean environment!

A new look at old things: we make furniture from clothes

This is not a fairy tale or fantasy old sweater can really turn into an original ottoman, not only very comfortable, but also a noticeable element of the interior. Making such a piece of furniture is very simple, because the main condition is an original, bright, beautiful or funny pattern on the sweater that you will use in your work.

So, you will need:

A sweater that you will no longer wear, but it is a pity to throw it away;
Scissors;
Threads and a needle;
Felt;
Fabric for the cover (lining material is perfect);
Styrofoam for stuffing.

From the felt, cut the bottom of the ottoman into a round or square shape. This part will serve as the primary blank. Take the sweater and turn the sleeves inside out, sew the remaining holes with an even seam. Sew the felt blank to the bottom of the sweater to make a bag-cover.

Tip: Using plain sweaters with large ribbed knits, such as rhombuses or braids, you will get an amazing classic-vintage ottoman that will look great in any interior. Such knitted patterns are suitable for square and rectangular shapes.

Now you need to prepare a cover made of lining dense fabric for expanded polystyrene. If your primary blank of felt is round, then you will need one piece of fabric of the required size (for example, 50 cm wide and 70 cm long), but if you decide to make a square ottoman, then calculate required dimensions for four pieces.

Sew all the pieces together, and leave a hem at the top for the lace, which will tighten the lace after you fill it with stuffing. The cover should be filled after you place it inside the sweater. Tighten the lace as tight as possible so that the filler does not wake up, straighten the sweater and enjoy your new piece of furniture!

Non-standard solutions in the manufacture of ottomans

Soft ottomans can be of any shape, even spherical. It will be just a great option for, which will become one of your child's favorite toys.

An ottoman ball is easy enough to make yourself, for this you will need:

Sewing machine;
Threads;
Needle;
Scissors;
High density fabric, two colors;
Graph paper for pattern making;
Polyethylene;
Silicone filler in the form of balls.

The process of creating an ottoman ball consists of the following steps:

1. First of all, you need to make a pattern on graph paper, observing the required dimensions. To make it easier, use a round object, such as a large balloon or floor lamp shade. Measure its circumference, and divide the resulting size in half. Divide this number into 5 parts so that 3 middle and 2 extreme are the same size. You will get the diameter of the base in the form of a circle and the width of the stripes that make up the spherical cover of the ottoman.
2. Transfer the resulting markup to the item you have chosen, starting with the circle part. Draw the next line down the pre-calculated bandwidth.
3. Take it, cut it along one side and cut off the bottom. Straighten and lay on the marks of the first strip, secure the edges with tape. Transfer a quarter of the strip to polyethylene and cut it out. In the same way, prepare the part of the middle strip. Transfer the pieces to graph paper before cutting.
4. Now the details of the ottoman need to be cut out of fabric in two colors, leaving 1 cm for a seam allowance. Sew them into strips, leaving one side open, and iron them out.
5. Attach the first strip to the round piece. The ends of the strip must exactly converge with each other. Stitch them and connect the round base with the strip with a seam, stepping back 1 cm from the edge.
6. Sew a similar blank for the opposite side of the cover and stitch to the middle strip. At the same time, do not overfill the ends of the middle strip. In the same way, grind the second semicircular blank with middle lane and iron the seams.

The cover for the ottoman-ball is ready, you just have to fill it with filler. To make the shape elastic, add pieces inside small size. Close the hole with a hidden seam.

We complicate the task: a wooden ottoman with a box for all sorts of little things

If you have skills in working as a carpenter, then you can easily make a fairly simple, but very beautiful and functional ottoman with a wooden drawer on wheels. In such an ottoman you can put toys, magazines, shoes or clothes. For it you will need:

laminated board or chipboard sheet for making a circle with a diameter of 30 cm and 4 rectangles 40 X 33 cm;
4 wooden beams with dimensions 4 x 8 x 8 cm;
PVA glue;
furniture wheels - 4 pcs;
metal corners- 4 things;
self-tapping screws;
screwdriver (screwdriver, drill);
foam rubber for stuffing;
fabric for the design of the cover;
sewing machine.

Take the pre-cut chipboards and connect them to make a box 40 x 40 cm wide and 30 cm high. Additional glue the joints.

Place on the bottom corners of the box. Fix them with self-tapping screws, smearing with glue for more reliable fastening. Attach furniture wheels to these bars. Install the cover with glue and screws.

The frame of the ottoman is ready, now you need to sew the cover. Take a special furniture fabric, it wears out less. According to the shape of the lid, open the top of the cape, and sew a strip of fabric 10 cm along the contour. Here you can also sew ruffles, drapery, canvas to your liking.

Lay a layer of foam rubber on the cover of the ottoman to ensure softness. Pull the cover over the top. For its implementation, you can use any fabrics and decorative elements.

Video about creating an ottoman with your own hands

As you can see, it is very easy to make an ottoman with your own hands, and the photos that we posted in this article will help you. Share with us in the comments your experience in the manufacture of such pieces of furniture, and we will be happy to discuss with you all the subtleties and features of such work! Comfort to your home!

Updated:

2016-08-13

Many today are wondering how to make an ottoman with their own hands. This is a very profitable and original solution. After all, this way you can make the desired piece of furniture, practically without spending money. Finding material is not difficult. And the shape and design of the ottoman can be chosen independently, which is not always possible when buying in a store. There are many options for how to make do-it-yourself ottomans for a bedroom from improvised materials. It is interesting that you can make ottomans even without complex patterns. So, you can make simple and soft ottomans with your own hands. Consider some of the simplest and at the same time versatile options for making this unpretentious, but necessary piece of furniture.

After looking at the photo of the ottoman for the bedroom, many will want the same for themselves. In fact, do-it-yourself ottomans are assembled in just a few hours. So, the first version of the do-it-yourself ottoman is the easiest. First you need to decide on the size of the future product. Next, take large sheets of paper and use a compass to draw a circle on them that will correspond to the diameter of the bottom and top of the ottoman (they should be the same). In this circle, two circles should be cut out of the fabric, which your ottoman will then be upholstered with. It is advisable to choose a dense fabric that does not “break apart” and is securely stitched. It is very important to leave allowances of about 2 cm around the circumference.

Now let's move on to the rest of the parts. It is necessary to measure the radius of the circle without allowances and measure this distance on another piece of fabric, and then set aside a distance perpendicularly, which will be equal to the height of the future ottoman. This will end up with a rectangle. Cut out the second exactly the same rectangle. And again, on each side of the rectangles, leave 2 cm for allowances.

Now start sewing the pieces together. Let's work with rectangles first. They must be sewn along the allowances between themselves in width, so that the result is one large long rectangle. Now you will need to sew a circle. It is sewn along the height of the rectangle slowly and carefully. The result is a cylindrical case that has no bottom. Such a cover can be put on any ottoman. And you can just fill this case with a soft material like cotton wool.

The circle on the bottom of the ottoman is sewn at the very last turn, when the inside is filled with soft material. And so that the edges of the circles at the top and bottom do not fray over time, you can attach a decorative ribbon to them.

Making a wooden pouffe

A do-it-yourself master class on ottomans will greatly facilitate the task. You will clearly see how the designs are made. But this is a more complicated option - making wooden ottomans with your own hands, in which you can put all kinds of things.

To work, you need to stock up in advance with self-tapping screws, furniture wheels and metal corners, wooden bars, a chipboard sheet for making the walls and bottom of the pouffe, foam rubber, upholstery fabric, as well as ordinary PVA glue.

So, for starters, we work with sheets of chipboard. You will need to do the following with your own hands. You need to cut 4 rectangles out of them. The height should be approximately 30 cm (which corresponds to the height of the pouffe), the width of each sheet should be 40 cm. The sheets are connected using self-tapping screws or metal corners, and the joints are coated with glue for greater reliability.

Now it's time to make the bottom and lid. To do this, a square is cut out from the same sheets or from a more durable tree according to the size of the bottom for the ottoman (this must be measured beforehand), after which the bottom is nailed to the frame using nails or self-tapping screws. The cover for the ottoman can be made separately. To do this, a square is simply cut out of the chipboard - a little larger than the dimensions of the pouffe hole. It can not be fixed at all, it will be a separate part. If there is a desire to attach the lid, then special hinges will be needed that will enable the lid to open and close normally.

So, the main part of the ottoman is ready. Now it remains only to give it softness and sheathe it with upholstery. To do this, foam rubber is cut out, the edges of which are smeared with glue and pressed against the frame of the pouffe. Please note that for the cover you need to use a thicker layer of foam rubber so that the product is soft.

When all the parts that should be soft are finished with foam rubber, it's time to sheathe the ottoman with fabric. The easiest option is to use the usual furniture stapler. It will be necessary to cut out pieces of fabric with a margin, so that later, stretching the fabric and bending its edges, attach it to the tree with a stapler. So the fabric will hold quite firmly.

At the end of the work, it remains only to attach the furniture wheels to the bottom. For this, self-tapping screws or screws are used - it all depends on the model of the wheels. And one more thing: the more heavy things are supposed to be put into the ottoman, the more powerful wheels you need to choose.

Pouf from an old sweater

Another option is a simple and neat ottoman made from an ordinary old sweater. To do this, first cut out the bottom of the ottoman of the desired size from the felt. Then take an old sweater, after turning inside its sleeves. On the front side, two holes will remain in the sweater, which must be carefully sewn together.

Now take a piece of felt and sew it just as carefully to the bottom of the sweater. The result is a kind of cover. Then you need to make the base of the ottoman. For this purpose, you can use the usual dense foam. It is best to make a square ottoman, as in this case it will be much easier to measure and cut a rectangle according to the height of the ottoman and a blank for the bottom. Then all the parts are glued together, after which a former sweater is pulled over such a base through the top. Now it remains only to make a hem for the lace at the top of the sweater fabric, sew the lace in there, and after filling the ottoman with cotton wool, tighten this lace tightly.

So, several options for making an ottoman for a bedroom are considered. There are many videos on the Internet that show in more detail how you can make such a piece of furniture with your own hands. Therefore, any woman, if desired, can transform an old pouf or make a completely new one. So, feel free to make a pouffe with your own hands.

How to make an ottoman with your own hands without throwing money away? Of course, you can buy it in a furniture store, but looking at the cost of a simple chipboard product, there is a desire to do crafts at home. If we consider furniture sets as a whole, then most of them belong to rather complex structures.

To make something from this list with your own hands is within the power of experienced craftsmen, and only an ottoman is made without special skills and knowledge from improvised means. A practical thing will turn out when a strong and high-quality upholstery fabric is chosen, which can be wiped, cleaned, washed.

Such materials include leather or upholstery fabric sold in specialized stores. It remains only to view step by step instructions for the manufacture of ottomans of various shapes.

So:

An ottoman for seating several people is comparable in height to an armchair and more like a soft bench. For the home, such a model is inconvenient, and not needed, but in the fitting and waiting areas it is very relevant.
Ottoman in addition to something with a certain height. From the definition itself, it becomes clear that it is not an independent product, but serves as an application. Models that barely rise above the floor are not designed to sit on them, but are used as footrests for adults. Children love such things in miniature and are happy to use them in their games.
Complementing armchairs, sofas, beds, sliding under the table or being a component in a non-standard combination (beach cabin with a pouffe), ottomans firmly occupy a niche in furniture stores. We can say more, there is a fashion for designer items that make the interior fashionable, complementing it.
The video in this article introduces poufs with advanced features. Looking through it, you remember the plot of the film, when “with a slight movement of the hand, the trousers turn into shorts”, and here the ottoman transforms into a full-fledged chair with a table, a bed with a lamp stand and others. necessary items while taking up minimal space.

Before you start making an ottoman with your own hands, you need to have an idea about this seemingly unpretentious furniture family.

So, poufs are classified according to materials, construction, functions and forms:

Textiles, leather are used on soft products. It’s nice to throw your legs on a do-it-yourself ottoman, and when sizes allow, then fall apart on it.
Rigid designs of ottomans are made of rattan, wood, often varnished, cork bark. Rigid ottomans, made by hand, are not very suitable for long-term sitting, but they bring liveliness and intrigue to the interior.

Attention: The ottoman definitely refers to the right thing, and its need is felt at the entrance to the house, more precisely, to the hallway.

How to make, sew, knit and what design of an ottoman to choose is not an easy task. The ottomans can be with exposed frames made of steel tubes or wood.
The ottoman may have closed frame , and the legs are hidden under the frills of a decorative skirt. Such products are popular with the British and Americans.
Pouffe on barely visible legs when copying a chair without armrests and backrest.
Do-it-yourself ottoman with a back- Not only comfortable armchair for members of the whole family, regardless of body weight, but also an excellent support for a sore back.
What could be simpler than an inflatable ottoman, consisting of a textile cover with a zipper and an inflatable chamber inside it? Ottomans differ not only in materials, designs, but also in shapes.
Do-it-yourself square ottoman, round, triangular, combined from different geometric shapes, can be made from improvised means.

Improvised tools in the house

How to make an ottoman yourself if you don’t have the skills and desire to cut, cut, twist? Craftsmen offer a lot of ideas and proposals brought to life. The work of making a cute ottoman is not difficult, but quite exciting, and a hand-made thing radiates special warmth and has an aura of home comfort.

Soft ottomans

The most simple circuit how to make a soft ottoman with your own hands is as follows:

Two circles are cut out of the fabric with a diameter equal to the diameter of the upper and lower parts of the product.

Tip: When cutting out the details, you should not forget to leave allowances for the seams.

Two rectangular parts of the same size are cut out:

width along the height of the pouf;
a length equal to half the circumference of the top and bottom of the pouffe.

Rectangular parts are sewn together on one side along the width to obtain a long ribbon.
One of the circles is swept to it and stitched along the seam.
The same is done with the second round.

Tip: If the seam is not too even or neat, it is sheathed with a decorative border.

The resulting pouf cover is stuffed with any suitable material.
A zipper is sewn into the unstitched edges remaining in the rectangular tape.

The photo shows a scheme for making a pouffe in the simplest way.

Similarly, you can make an ottoman having the shape of a cube. The difference is in the manufacture of parts that must be square in shape, and for the manufacture of the sides, four parts will be required from the fabric, and not two.

Then:

The details fit together.
To more clearly indicate the edges of the cube, you can use a canvas of a different contrasting color.
Additional strength, elasticity will give a denser fabric.
The stuffing of such a pouffe can be done with synthetic winterizer and foam rubber. These materials hold their shape perfectly and do not deform.
A hole for stuffing the material is made at the bottom of the pouffe so that it is not visible.
If desired, it can be stitched tightly after stuffing the pouffe, or a zipper can be sewn in, so that the material can be replaced if necessary.

Sewing an ottoman

The video in this article demonstrates the procedure for sewing an ottoman of 8 elements. To do this, a sheet of paper is folded four times, a template is drawn on it and cut out according to the diagram below.

The unfolded template is fixed on the fabric and cutting of blanks in the amount of 8 pieces begins.

Attention: It is not necessary to purchase for a pattern new fabric, you can use old deposits of knitted clothes, old sweaters.

The photo below shows that the sharp end of each hexagon is bent inward by about 5-6 cm and stitched on a typewriter, which allows you to get an octagonal hole for stuffing the finished product after assembling all the elements.

The blanks are attached in pairs to each other with an indent from the edge of about 1 cm. The pairs are added front side so that the seams are obtained from the wrong side, there are 4 segments of 2 blanks in the stitched form.
Similarly, they are sewn together in 2 sections and 2 halves of the future ottoman are obtained.
The halves are connected to each other on a typewriter, the cover is turned inside out.
The ottoman is stuffed with prepared filler (holofiber, foam rubber, synthetic winterizer), and the hole is closed with a cap of the appropriate size. The edges of the lid should already be finished, and it is manually, carefully sewn on top of the stuffing hole.
The instruction for beginners recommends sewing an ottoman with literally three seams. Why cut out 2 circles, the diameter of which is about 50 cm or 2 squares, if you like clear lines more. Geometric shapes will serve as the top or bottom of the future product.
From the same material or from another, a strip is cut out with a size corresponding to the circumference or perimeter of the square, the width of the strip depends on the height of the ottoman. The height of the ottoman, in turn, is selected depending on the function that the product will perform, whether it is a footrest, a seat in the hallway, a toy for young children or a structure in the living room.

Attention: Cutting the strips for the sidewall of the ottoman is done taking into account the allowances for the seams.

The work is carried out in such a way that the seams are on the wrong side, the strip is sewn first of all to the bottom of the product and only then to the top.
After stitching all the seams, the ottoman is turned to the front side and stuffed.
According to the same patterns that are presented above, for the first option and for the second, covers for an ottoman with a zipper are cut out. This will allow in the future to wash the cover or clean it without unnecessary problems and time-consuming, and not solve the problem of how to sheathe the ottoman with fabric if it is already made of fabric.

Reliable base for plastic bottles

Plastic bottles are available in every home in unlimited quantities. Take at least bottles of beer and water with a capacity of 1.5 - 2 liters, their color in the finished product does not matter, and they will help to unload the rubble in the yard and house.

To make a good, stable ottoman, you will need at least 16 bottles with a capacity of 1.5 liters or 9 pieces of 2 liters.
Packaging cardboard from household appliances also waits for its turn and is not thrown away for years, what if the refrigerator breaks down, how to take it for repair? The video in this article will show how cardboard is used in the manufacture of an ottoman from plastic bottles.

It is necessary to stock up on tape, foam rubber and upholstery.

Hot glue gun, zipper for case.

Attention: From round bottles you can make an even larger circle, square or rectangle, that is, the shape of the product is chosen from your preferences.

For ease of use, if a very large ottoman is planned, the bottles are connected into separate sectors and sections with adhesive tape, and then the formation of the overall structure begins.

If the future product is planned to be round, then the ottoman needs to be made starting from the middle.
For this, a bottle is taken and, with movements along the radius, new elements are attached to it, which are carefully fixed with adhesive tape to each other.
After the circle is completed, the base is cut out of thick cardboard. It should be slightly larger than the bottle design.

Cardboard is also fastened with adhesive tape in several layers. Once again, there is no need to dwell on the point that 2 grounds should be prepared, and so everything is clear.
The turn of soft upholstery has come, for which two parts for the top and bottom are cut out of a dense foam rubber web, which are glued in place.
From the remaining part of the foam rubber, a rectangle is cut out according to the size of the circumference line of the side part, which wraps around the pouffe.
There remains the final stage of sewing a cover made of furniture fabric, preferably with a zipper. This operation will not only allow you to easily remove the laundry cover, but also make several options and update from time to time appearance of your product.

Ottoman from a grandmother's rarity

How to make an ottoman out of a stool so that grandmother's rarity will serve for more than one year?

Indeed, a stool made of solid wood, well-knit at one time, painted oil paint, may please the owners for many more years, but the appearance does not correspond to the modern situation. Reworking an old stool into a stylish ottoman will help to balance the interior.

The design of the stool is pre-strengthened with self-tapping screws.
The legs are a little shortened - do not forget to check the level so that the ottoman does not stagger later.
The frame of the future ottoman is being assembled, for which 4 sheets of plywood are used. They are attached with screws to the legs of the stool.
The fifth sheet of plywood is screwed from below and serves as the bottom of the future craft.
The foam for the seat is cut out with an allowance of 5 cm.

Attention: The upper part of the ottoman is smeared with glue, then the foam rubber will not stray over time into an untidy lump.

The upholstery fabric on the seat is fastened together with foam rubber using stapler staples.
The foam rubber on the sides can be attached with slats, which help to give the ottoman a round shape and make it more beautiful.
The remaining part of the structure is made out with a fabric, fixed with staples.
The wheels are screwed on or, as in the photo above, cute little legs of an updated stool peek out from under the coquettish upholstery.
The task of how to make an ottoman from a stool was solved in a short time.

For lovers of knocking

The rich Russian language causes many associations and questions. How to knock, where to knock, when to knock? For those who like to hit a nail with a hammer, it is proposed to make an ottoman with your own hands from boards and chipboard.

Pre-prepared rectangular pieces of 40x30 cm from chipboard in the amount of 4 pieces.
Circle with a diameter of 30 cm and wooden blocks 4 pieces.
Glue for wood.
Furniture wheels with special fasteners.
Metal corners, self-tapping screws.
Foam rubber and upholstery fabric.

As you can see the set the right materials does not differ much from each other when we make an ottoman with our own hands, even in different ways:

A box is assembled from rectangles. Metal corners, self-tapping screws are used, all corners of the structure are aligned, they must be straight.
On the lower part, the bars are fixed with glue, on which the wheels will be located in the future.
From above the base on individually picked up form fastens.
The finished frame is upholstered according to the same type of technology using foam rubber, fabric and a zipper on the cover.

For lovers of knitting and stuffing

How to make a do-it-yourself ottoman frameless and therefore soft. Crocheted needlewomen will be able to knit a soft ottoman much faster, but not everyone may like their appearance.

Lovers of working with knitting needles present interesting models of ottomans, knitted specifically on them:

For work, you will need the thickest knitting needles that are available in stores.
Quite thick wool is suitable for knitting needles with a diameter of 9 mm.
Ordinary threads offered in stores are too thin. The price for them is not high, but due to the fact that you have to make thicker ones out of them, weaving them together, you will have to buy enough a large number of which adds value to the product.
Of course, you can cut, unravel, twist unnecessary knitwear, which takes a lot of time, and it’s quite problematic to find the right amount of plain knitwear that has fallen into disrepair at home.
It seems that the solution to the problem of how to make an ottoman with your own hands has reached a dead end, but cotton clotheslines caught my eye.

Warning: Synthetic clothesline is not suitable for this job, and cotton ropes are difficult to obtain in small towns.

For a soft ottoman of sufficient size, 20-30 of these ropes are required, which are tied into a long rectangle.
The side is fastened with a rope to get a spacious, wide skirt.
The bottom is pulled together with a rope of the same color and a bag is obtained that needs to be stuffed with something. There are 2 options here - use junk neatly folded on the shelves in the closet or go to the store and purchase foam rubber or holofiber.

From unnecessary junk, the ottoman turns out to be heavy and not as round and lush as from store materials, but it frees up space in the closet for new clothes.
The top of the ottoman is made out with the same rope and you can try out your product.

Ottoman from an old bucket

Here's another one interesting solution, for which we will need: an old plastic bucket, a thick jute rope, a hot glue gun, a stapler, scissors, a furniture locker handle, Velcro tape, upholstery fabric and several new microfiber cloths. You will also need cardboard, but it will be better if you replace it with thin plywood.

First of all, wash the bucket and remove the metal handle from it.

Next, use hot glue to glue outer surface bucket rope, starting from the bottom.

Cut the end of the rope and carefully hide.

Place the bucket upside down on cardboard and circle it. According to the intended pattern, lay out the upholstery fabric and cut off a round blank with a 5 cm outlet.

We make a hole in the center of the cardboard and fabric. We pass through them a bolt from a furniture handle and wind the knob.

Next, we roll the fiber into tubes and wrap the bolt radially between cardboard and paper, creating a kind of roll. To prevent the fiber from unwinding, securely fix it with glue.

Then the fabric is stretched and fixed on the back side with a stapler.

To hide the traces of cardboard, close reverse side seat with another piece of fabric that needs to be glued on.

Cut the Velcro into four equal lengths and stick them crosswise on the bottom of the bucket and the base of the saddle - with the bristles to the bucket, and the fluffy part to the seat. Connect the two pieces. Hooray! The pouf is ready!

The result is such a useful craft, which you can comfortably sit down on.

Various options provide an opportunity to solve the problem of how to make an ottoman yourself from improvised materials, which are available in abundance in any home. The only thing I wanted to focus on was the floor in the room.

Laminate is quite sensitive to mechanical stress, so it is better to make an ottoman without wheels and legs, that is, with a solid bottom. On a soft floor, carpet, carpet, ottomans on rollers are appropriate, but there are no restrictions for tiled flooring, unless forged legs can be an exception.

Chipboard ottoman

In one toast, the hero of the "Prisoner of the Caucasus" expressed the very essence of being, so that "our desires coincide with our capabilities." There is free time and a desire to make an ottoman with your own hands from chipboard - you need to prepare opportunities.

Tools and necessary materials stock up in advance.

A good ottoman cannot be made without a solid base from a chipboard sheet. Optimal size construction is within 400x400x500 mm.
You can make a wooden ottoman using a simplified technology, making a frame in the form mailbox from the timber and fasten it with the cuts of the side, but since the ottoman is made for yourself, you can try.

Work with pleasure

FROM bad mood you should not take up work: something will fall on your foot or you will hit the wrong nail with a hammer.

It is marked out, cut out from a sheet of chipboard 5 squares 400x400 mm for the manufacture of the walls of the structure and the bottom.

Attention: The bottom of the ottoman should not be made of plywood, small children like to hide in secluded corners, they can break through thin plywood and get injured.

The cover is made of any geometric shape: square, round, oval. Beginners may not experiment and stop at the square cover. It will have dimensions slightly larger than the main box 430x430 mm in order to protect it from falling inside.
The height of the finished product is made up of the constituent elements - the height of the structure is 400 mm, plus the rollers are 50 mm, the bottom and tire are 32 mm thick, the upholstery is laid in 50 mm, a total of 532 mm.
From the prepared elements, the formation of the structure begins.
The sides of the ottoman are fastened with metal corners. To strengthen the rigidity and reliability will help the bars, which are glued to all internal corners.
From the front side of the ottoman, self-cutters are screwed into the bars, the caps of which must be recessed into the tree, so that later there will be no problems with torn upholstery.
The lower part of the box along the perimeter is smeared with carpentry glue, capturing the ends of the bars.
The bottom of the ottoman is attached, and the cutters are again screwed into the ends of the bars. The assembled structure should dry well.
The base of the ottoman is made, but there are no wheels and a lid yet, on which you can sit in the future.
The cover is fixed with 4 bars screwed from the inside. The work is carried out after there is confidence that the lid closes smoothly and the stiffeners on the side do not interfere with the closing of the lid.
The finished structure is turned over, and the wheels are fastened with cuts.

Attention: They are fixed through the bottom to the ends of the bars, for which small holes are drilled in the bottom.

Before continuing work, it is necessary to make sure that the resulting structure is sufficiently stable, holds the person sitting on it well and there are no flaws that interfere further work otherwise it makes no sense to start upholstery.

The ottoman is getting dressed

Do-it-yourself ottoman made of wood, chipboard or generally soft needs clothes on top. This function is performed with honor by a solid, upholstery fabric, neatly attached to the crate of the structure.

First, the cover of the ottoman is made, for which a soft lining is cut out of foam rubber, synthetic winterizer, batting. The size of the pad should match the dimensions of the seat so that it is neatly, without hanging down, glued into place.
From the fabric intended for upholstery, a blank is cut out somewhat larger than the cover. This is done so that the edges can be bent under the lid and fixed from the inside with a stapler or furniture studs.
The instruction prescribes to further issue sides ottoman.
The detail is cut out upholstery fabric 400 mm x 4 = 1600 mm with a margin for connection. Also in height, the material must have an allowance at the top and bottom.

Attention: The fabric must be trimmed, stretched, tucked inward, the edges secured with furniture studs or a stapler.

The seat is decorated, the niche is upholstered, all edges are carefully closed and you can present the finished product for control to demanding family members.
Do-it-yourself plywood ottoman is made according to the same scheme, if this simple design option is chosen.
The work becomes a little more complicated when an opening drawer is provided on the ottoman, then the stop bars are replaced with door hinges.

Getting acquainted with the design of this simple piece of furniture, one detail catches your eye: despite the difference in the shapes of ottomans and their types, the base is a rigid frame, there is a seat and legs. They are decorated in different ways, but quilted leather or leatherette give the products an elite, luxurious look and you can’t immediately determine that the price of the product is within reasonable limits.

Although, it should be noted that a neat ottoman, sheathed in a different material, is able to bring comfort and convenience to the room and looks no less elegant than leather.