Interlining is a material made of cellulose fibers, which are bonded together with a polymer. This is the so-called "improved paper" because it is stronger and more resistant to abrasion, with a high level of fire resistance. Non-woven is often used for painting. By repainting them several times, you can quickly update the interior in your home. How to glue non-woven wallpaper? This topic is covered in an article written by our expert.

The advantages are:

• thanks to the non-woven base, it is possible to mask small irregularities on the surface of the walls during wallpapering;
• they have a textured surface that resembles decorative plaster;
• it perfect option if you need to change the look of the room without spending a lot of money, effort and time;
• in the absence of a vinyl layer, non-woven wallpaper can freely pass air, because of its wall they “breathe”;
• a high degree of resistance to fire, and, consequently, fire safety;
• they are easier to stick than paper ones: you don’t need to lay out the wallpaper on the floor for spreading with glue;
• they can be washed with water and detergents;
• vinyl with a non-woven base does not accumulate dust, therefore such wallpapers are a salvation for those who have bronchial asthma or allergies;
• characterized by resistance to fading when exposed to sunlight;
• they are easier to remove from the walls than paper wallpaper.

Flaws:

• upper layer sensitive to different kind damage, therefore, if there are kids and animals at home, voluminous wallpapers will quickly become unusable;
• pay attention to environmental friendliness when choosing. Interlining is called large group materials that are characterized by varying degrees of environmental safety. By purchasing cheap wallpapers, you risk, because. they are most often made from low quality raw materials. Buy wallpaper from trusted brands;
• their cost is higher than that of paper ones.

What is needed for pasting?

If you are wondering how to properly glue non-woven wallpaper, we recommend that you read the article to the end and prepare everything you need for pasting.

You will need wallpaper, a spatula, a roller or brush, special glue, a brush, plastic corners and a level.

Preparation for pasting walls with non-woven wallpaper

Wall preparation and marking

Preparation begins with the removal of old wallpaper, dust from the walls, as well as the elimination of surface defects, the removal of a layer of paint. At a minimum, it is worth treating the painted surface with medium caliber emery, and then with a primer.

Non-woven wallpaper has high-quality edges, so you can glue them "butt". The panels that are located side by side look like a single canvas. Such wallpapers are often produced in widescreen, therefore we will talk about gluing wide wallpapers. It is recommended to start work from the corner of the room. From the corner, using a level, draw vertical lines at a meter distance from each other.

When gluing, try to stick to these lines. The width of the wallpaper is usually 1.06 m, so there is a 6 cm margin that will come in handy when making a joint in the corners of the room.

Wallpaper preparation

When the wall markings are ready, prepare the wallpaper. It is better to cut blanks on all the walls in the room. The degree of complexity of this work depends on the pattern on the wallpaper, but if it is not there, there will be no difficulties. Before cutting the workpiece, measure the height of the wall at its various points (for example, every 30 centimeters). When you make sure that the height is the same on all walls, cut the wallpaper blank to the size you need.

When sticking wallpaper with a large pattern, select it: during the marking, make sure that the patterns match. It is important that there are no mistakes and that you do not have to glue pieces of wallpaper above the floor or under the ceiling.

Glue preparation

Use special glue (it is thicker than usual, does not leave yellow spots after drying). For vinyl wallpaper it is better to use glue that is designed specifically for heavy wallpaper. Pay attention to the labeling on the packaging, as well as the recommendations of the manufacturer, so as not to make a mistake in choosing an adhesive.

Step by step instructions for sticking non-woven wallpaper

How to glue non-woven wallpaper? Let's bring step by step instructions for wallpapering.

1. The glue is applied in a thick layer with a roller on the wall or with a brush to a width slightly larger than the width of the wallpaper sheet, then a dry sheet is applied. The strips are glued end-to-end: doing this carefully, you will not see the joints. When glued with an overlap, they will have a sloppy look, because the surface thickness will be higher than usual, and this can cause a damaged interior.
2. It is not difficult to dock the canvases, the material is dense, it does not tear or stretch. The sheet can be removed without consequences and pasted again.
3. You need to start pasting from the corner. In the place where the 1st panel ends, draw a vertical line. Focus on it, gluing the strip. The quality of pasting depends on the 1st sheet, since other strips are glued end-to-end to it.
4. Apply adhesive to the wall in 2-3 strips, apply the 1st sheet to the wall, starting from the top, pressing it and smoothing it with a spatula, removing air bubbles. Make sure that the edge matches the vertical line you drew.
5. If the glue is dry, unscrew the edge of the wallpaper, smear the wall with a roller or brush again. Finally gluing a strip of wallpaper, cut off the excess with a spatula or clerical knife under the ceiling and above the floor. Do not align the bottom edge too carefully, you will cover it with a plinth.
6. Glue the next strips, focusing vertically on the canvas in the neighborhood and tracking the pattern match, paying attention to a snug fit at the joints. Glue from the wallpaper on top can be wiped with a brush or cloth, no traces will remain.
7. Cut the wallpaper in the corners, and then glue it end-to-end. Do not seal the corner with a solid strip, otherwise inaccurate folds will appear in this place. After completing the work, make sure that all the canvases are securely held, if they are lagging behind in some places, spread them with glue and press them against the wall.

Taping corners and awkward areas

When gluing, maximum attention should be paid to the corners in the room, carefully smearing them with thick glue. It is recommended to use plastic corners that can be attached to wet putty to get a neat result.

What to do when bubbles appear?

If bubbles appear during the gluing process, move a piece of wallpaper away from the wall and glue it again, gently leveling the surface.

If a bubble arose after the non-woven wallpaper dried, then you can take a thin needle and pierce the place of its appearance. Then it is necessary to level the surface with a spatula and stretch the wallpaper.

You can use a syringe to inject glue under the wallpaper, they will provide the necessary tightness of the wallpaper to the wall so that the bubbles disappear.

How long does wallpaper take to dry?

When drying wallpaper, humidity and temperature in the rooms are important. Sudden changes in humidity, sudden movements of air masses should not be allowed, therefore, during drying, it is necessary to close all doors and windows.

The use of heaters during drying is impractical, it is better to dry the wallpaper in a natural way with well-functioning ventilation.

How to care for wallpaper?

If you purchased a washable wallpaper based on flaselin, then the degree of their protection against water is indicated on the roll.

The symbol of 3 waves is evidence that the wallpaper is not afraid of moisture, they can be wiped with a wet cloth, the symbol of wave 1 allows you to wipe them with a damp cloth, the symbol in the form of a brush can be washed with.

It is not allowed to wash embossed wallpaper.

Is it possible to glue non-woven wallpaper on old wallpaper?

When pasted on top of a layer of wallpaper, the old panel may peel off. In addition, color mismatches are possible, especially if the bottom layer is darker. If you remove a layer of old wallpaper and leave the base on the wall, then gluing a new canvas is advisable only when the base is firmly held. By their type, they must match the new wallpaper.

Do not leave a paper base if you want to stick wallpaper that does not allow steam to pass through, for example, if they include metal. Walls with applied oil paint or varnish - unsuitable coating for non-woven wallpaper. If you have pasted something on them, do not rush to remove the old layer of coating, it is better to stick a new layer of wallpaper on top of the old one, making sure that they hold securely.

In stores there is a special tool for replacing wallpaper, which can be applied to a dry surface before sticking, then after the end of their service life they can be easily removed. Due to the composition, the product easily penetrates the structure of old wallpapers. They can then be removed without wetting the wall, in a dry form.

When removing old non-woven wallpaper, take them by the edge (for example, near the baseboard) and slowly separate them from the substrate. There is no need to lubricate the wall, the front layer will peel off entirely or in stripes. If the base holds well, no damage is found, then new canvases can be glued on top.

If the peeling of the base has begun in pieces, and the top layer cannot be removed in some places, then you need to remove 2 layers entirely, otherwise the base for new finish will be of poor quality.

1. The substrate of old non-woven wallpaper is resistant to damage, strengthens the walls, and prevents cracks. It is necessary to treat this base with a layer of primer and you can glue wallpaper, apply decorative plaster, etc.
2. First of all, it is worth considering that interlining is a transparent material. If the vinyl or paint layer is not thick enough, uneven wall tone can be detected through the wallpaper. With inaccurate wall plastering, for example, only in places where drywall sheets adjoin each other, this will be revealed if the wallpaper is light. Before sticking, attach non-woven wallpaper to the wall, turn on bright lighting and see if there are any dark spots. If they are, you must first align the color of the walls. If the wallpaper is needed for painting, it is better to paint over with 1-2 layers of paint so that there is no translucence.
3. When repainting, even if it is done several times, the structure of non-woven wallpaper does not change, but the strength and sound insulation increase.
4. Other repair and decoration work in rooms with pasted wallpaper cannot be carried out during the drying period.

Conclusion

By re-sticking non-woven wallpaper several times, you can quickly update the interior in your home without applying high costs time, effort and resources. We hope our article will help you with this!

If during the repair you want to update the walls with a high-quality and beautiful coating, construction counters will definitely offer non-woven wallpaper. The material has high operational characteristics and a lot of pluses, looks great and unpretentious care.

Non-woven wallpaper - durable and elegant coating

The main place in the composition of this rolled web is occupied by cellulose fibers, which are natural components. The rolls themselves are divided into two types:

1. non-woven, created from several layers of 100% non-woven, give texture to the topmost;
2. on a non-woven basis - they include two layers, one of them is pressed from cellulose fibers, and various components (vinyl, paper, textiles, etc.) are applied to the second, which form a relief pattern.

The advantage and characteristics of non-woven wallpaper for walls

Due to its positive factors and strength characteristics, this coating has gained popularity among buyers. Main positive traits non-woven fabrics are given below:

• elimination of small irregularities due to its density and embossed texture. It follows that there is no need for a perfectly smooth base surface;
• the existing versatility allows the use of the material on any surface;
• vapor permeability / fire resistance;
• safety for health, since the canvas is non-toxic;
• suitable for painting;
• good moisture resistance, which makes it possible to use them in the bathroom and in the kitchen;
• resistance to external influences guarantees durability.

How to stick non-woven wallpaper on the wall

Before you start attaching the canvas, you should prepare the base surface - clean it with a fine-grained sandpaper from the old coating and glue.

Non-woven sheets have translucent properties. The base must be washed from inscriptions and various kinds of pollution.

Then do the following:

1. Remove switches and sockets.
2. Prime the wall to prevent mold.
3. Let dry.
4. Eliminate large chips and errors with plaster putty.
5. After the putty has dried (on average in a day), proceed with the preparation of the adhesive composition in accordance with the requirements.
6. Measure the required heights, add a margin of 10 cm and cut the wallpaper strips.
7. Apply the adhesive to the wall in a thick but even layer. Necessarily! Glue is applied exclusively to the walls. They do not need to cover the canvas.

If you have a picture before cropping, be sure to perform a selection so that the result looks like a single holistic picture.

Only after the performed operations are allowed to proceed to direct gluing. Holding the upper part of the cut strip, you need to attach it to the wall in such a way as to fix it exactly relative to the surface. Having fixed the sheet from above, you need to move to its lower part. After fixing, smooth the material by moving the roller or brush from the center to the edge. Remove excess glue with a rag. When applying the following sheets, it is worth smoothing the joint area properly.

What glue to glue non-woven wallpaper

Glue for this type of material is used in a special, thick consistency, since the canvas has a considerable weight. The adhesive composition is gradually poured into a container with water, while constantly stirring the resulting solution. After thorough mixing, let the glue stand until it swells.

Excess adhesive solution can be left with a roller in a special plastic grid.

How to glue wide meter wallpaper

Rolls in most cases are presented with a width of one meter. This format saves time as the workflow is faster. In addition, the seams as a result of gluing will be two times less, unlike rolls with a width of 0.5 meters. The process of gluing sheets of meter width according to the technology does not differ from the standard one.

Pasting the walls with non-woven wallpaper in the corners

When gluing corner sections, you should follow some simple rules:

• attach the canvas so that an overlap of 2 cm is formed on the adjacent wall;
• do the same with the sheet on the adjacent wall;
• gently press down on the material along the entire height of the corner until it touches the wall;
• after drying, remove with a clerical knife the extra fragments protruding to the ceiling.

Joint Features

Each strip is glued together butt-to-butt. Sometimes you can find brands whose instructions require overlapping sheets. Butt joints are especially important to smooth with a roller.

What is important to remember

Before work, it is necessary to calculate the amount of the required finishing material: the sum of the areas of the walls and individual sections must match the area of ​​the roll multiplied by their number.
Throughout the entire working process and until the glue has completely dried, it is important to avoid drafts in the room.

It is worth gluing the wall with non-woven sheets from the corner section by the window.
Remove excess pieces of material with a clerical knife only after they have completely dried.
The non-woven coating for painting can be filled with color only after the glue has completely dried.

Do not rush to throw away the remnants of the finishing material. They can be useful for finishing small areas or correcting errors.

Adhere to the standard gluing technology, but be sure to first read the instructions on the roll. In case of differences, the latter shall be followed.

Caring for non-woven wallpaper

To maintain the cleanliness and good appearance of the finishing coating, it is enough to periodically wipe it with a damp sponge and vacuum.

Wall covering with non-woven material is reliability, style and comfort in the house. The cost of rolls of this series can hardly be called low, but the quality is worth it. The room will sparkle with notes of elegance and nobility.

Useful video

Anton Tsugunov

Reading time: 5 minutes

Non-woven wallpaper is becoming more and more popular and is gradually replacing its paper counterparts. This is due to the presence of a number of positive properties: resistance to deformation, durability, the ability to hide minor defects in the base, the possibility of subsequent painting. How home master, and a professional finisher needs to know how to properly glue non-woven wallpaper.

Features of gluing non-woven wallpaper

At the heart of this finishing material is used interlining - nonwoven fabric from cellulose fibers.

Before starting work, you need to get acquainted with several important features of this wallpaper:

• canvases do not stretch and retain their original size;
• the width of the rolls is often 700–1400 mm, due to which fewer strips are required to finish the room than when using standard half-meter-width wallpapers;
• glue non-woven fabrics end-to-end, without overlaps. An exception is the gluing of corners (but more often the masters make the joint with a double cut);
• glue is smeared only on walls or ceilings, the canvases themselves are applied dry.

Gluing non-woven wallpaper with your own hands is easier than paper-based canvases.

Tools and materials for work

TO necessary fixtures and materials include:

• roller for applying glue (preferably with a long pile);
• brush or brush for processing corners and hard-to-reach places;
• a bucket for diluting glue;
• tape measure 5–8 meters;
• laser level or building plumb line (the simplest device can be made independently);
• plastic spatula for smoothing stripes;
• sponge to remove excess glue;
• dry rag;
• pencil.

Particular attention should be paid to the preparation of glue: it should be designed specifically for non-woven wallpaper. Recommended by some consultants in stores universal composition has, as a rule, much less adhesion in relation to interlining. With its use in the future, the canvases may begin to move away.

Wall preparation

For high-quality wallpapering, the walls must be prepared. Main stages:

• Removal of old canvases or paint. How to remove the old finish with minimal effort is written. All methods for removing paint are set out in. If the paint layer is very strong, then the surface should be treated with medium grit sandpaper.
• Plastering - carried out with significant irregularities.
• Priming with a deep penetration compound.
• Leveling surfaces with putty.
• Re-priming. Masters recommend that instead of the usual primer, apply a thin layer of wallpaper paste to the walls.

In more detail, all the stages of preparing walls for wallpapering are described in. The rules for preparing drywall will be different; step-by-step instructions for GKL can be found.

Surfaces must be completely dry before sticking canvases on non-woven fabric.

markup

Work begins from any corner of the room. It is allowed to glue the first sheet with an indent, for example, if the calculation of the number of blanks with a pattern around the entire perimeter of the room showed that it is better to do the finishing joint not in the corner, but the corners themselves are quite even. In any case, you need to glue the first blank as evenly as possible: all subsequent work depends on this.

• A distance equal to the width of the wallpaper minus 2 cm retreats from the corner.
• Using a laser level or a plumb line, a vertical line is applied to the wall with a pencil.
• If the wallpaper is light, then they do not draw a solid line, but make notes at the top, bottom and in the middle.

Similarly, they pass the entire room. Even if overlaps are made somewhere in the corners, these lines will help you navigate the correct gluing, especially if canvases with a pattern are selected.

Material cutting

This process looks like this:

• A roll of non-woven wallpaper is rolled out and the height of one sheet is measured.

• Draw a line with a pencil using a ruler. The canvas is folded along it, laying the roll on top, and carefully smoothing it.
• Next, cut off the first blank with a knife or scissors.

• They measure the height of the room at different points and, taking into account a small margin, cut the required number of sheets.

If non-woven wallpaper has a pattern that requires docking, you need to find out the size of the rapport - the height of the repeating image. The length of the cut strip must be a multiple of this number, but be sure more height premises.

• The necessary margin in height will allow you to shift each sheet for an accurate selection of the pattern. To simplify the work, you can periodically apply two sheets together in order to check the conformity of the image.
• Wallpaper cutting is always performed sequentially on one side of the roll.

At this stage, the main thing is not to make a mistake in size, so that you do not have to glue the missing pieces.

The technology of gluing non-woven wallpaper on the walls

Step by step instructions for gluing:

• Diluted glue is applied with a roller on the surface between two lines. You need to capture a width slightly larger than the size of the wallpaper. This will help the joints stick well.
• The top, bottom edge and corner are smeared with a brush, since there is always less glue here.
• The finished sheet of non-woven wallpaper is held by the upper corners, gently applied to the wall and, starting from the top, smoothed with a plastic spatula, but no strong pressure is needed. Particular attention is paid to the exact correspondence to the previously made vertical marks on the wall.

If the wallpaper has a deep texture, then it is better to use a wallpaper roller to avoid damaging it.

• Remaining air and excess glue are removed with a spatula from the middle to the sides.
• The glue that has come out must be immediately removed with a damp sponge or cloth, and then wipe these areas with a dry cloth.
• The second sheet is glued end-to-end to the first.

Do not be afraid that gaps will appear at the joints: non-woven wallpaper does not change its size after drying.

The rest of the sheets are glued in the same way.

It is necessary to ensure that the glue on the wall does not dry out, especially in places where the edges of the blanks are glued, otherwise the canvases may move away.

For this reason, it is desirable to work with non-woven wallpaper quickly. When it is clear that little glue has been applied, it is better to immediately smear this place by bending the sheet.

Trimming "tails"

It is more convenient to trim the wallpaper when it is already dry. The cutting technique is as follows:

• a wide metal spatula is held almost vertically and pressed against the top or bottom of the wall;
• the knife is driven strictly parallel to the spatula, without tearing it off, only the spatula moves.

The nuances of pasting corners

With perfectly even wall joints in the room, non-woven wallpaper can be glued to the adjacent surface. But this rarely happens. More often in the corners, the double cut technique is used:

• The sheet is glued with an overlap (2-5 cm is enough).
• A metal spatula is applied to the junction of the blanks.
• Both sheets are cut with a clerical knife.
• After that, the cut off upper strip is removed. The joint will be smooth and almost invisible.

It is important to press the knife not too hard so as not to cut the putty on the wall, which can crumble, but not too weak, otherwise only the top sheet will cut through.

• When the procedure is completed, both blanks are pressed tightly against the wall, if necessary, additional glue is applied and the joint is smoothed out.

HELPFUL INFORMATION: How to calculate the required number of wallpapers per room: a simple formula

When a pattern is joined, especially a large one, sometimes you have to glue the wallpaper from the corner in the opposite direction. In this case, overlaps are possible depending on the width of the workpiece.

We glue wallpaper around sockets

In advance, holes for sockets and switches are not made in the canvases, since it is difficult to calculate their location, and it will be more difficult to glue the sheet. It would be better to do this:

• First remove the plastic cases and turn off the electricity.
• Glue the wallpaper blank and carefully pierce the canvas in the center of the outlet hole.
• Make small cuts crosswise and bend the pieces.
• After graduation finishing works lock the housing in place.

How to glue non-woven wallpaper on the ceiling?

The technology of gluing non-woven wallpaper on the ceiling has no fundamental differences from the work on the wall.

• When pasting the ceiling, it is advisable to get an assistant who will support the sheets.

Russia, Moscow region, Moscow +79041000555

How to glue non-woven wallpaper correctly: rules and step-by-step instructions

It takes ~4 minutes to read

Save

Non-woven wallpaper at one time turned the idea of ​​\u200b\u200brepair. They have a lot of advantages and are easier to glue. With certain knowledge, the whole process can be done with your own hands, having achieved a good result, you just need to understand the technology. In this article, we will consider how to properly glue wallpaper and prepare walls for high-quality repairs.

The technology of gluing non-woven wallpaper differs little from paper and vinyl types of wallpaper. The basis of their gluing is similar, it requires preparation, accuracy and patience. At the same time, you need to know the nuances of working with them.

Save

Required Tools

For high-quality gluing, you need a large number of auxiliary tools. You can do without them, but with their use the gluing process will become easier and faster.

Required tools:

1. Roulette.
2. Pencil.
3. Roller or brush.
4. Knife or scissors.
5. Glue container.

Save

When buying tools, you should know that a roller is more convenient than a brush, and a clerical knife is preferable to scissors. In the first case, the speed of applying the glue will be higher, it will lay down in a more uniform layer. The knife will allow you to cut the blades with an even cut without notches.

Additional tools:

1. Ladder.
2. Long line.
3. Water container.
4. Building level.
5. Small metal spatula.
6. Soft bristle brush for smoothing wallpaper.
7. Tray and mesh to remove excess glue from the roller.
8. Foam sponge and/or cotton towel.
9. Rubber or plastic spatula with soft tip.

You can do without these items, but they will speed up the gluing process and allow you to achieve a higher quality of work. At the same time, it is difficult to get a good result on unprepared walls.

Marking and preparing walls

Save

The structure of such wallpapers allows them to be used on walls that are not perfectly even. At the same time, there should be no frank bulges, pits or cracks on the surface. Their elimination is included in the first stage of preparation.

It is important not to forget that they cannot be glued on surfaces covered with oil paint. You need to first sand the walls a little with medium-caliber sandpaper.

Acrylic paints do not interfere with sticking non-woven wallpaper. This type of painting does not need to be sanded, if the walls were pasted over with other wallpaper, then they simply need to be removed. It is also necessary to clean the surface of dirt, cobwebs or accumulations of dust.

It is worth remembering that gluing non-woven fabrics requires a relatively uniform surface color. They are a little translucent, so if there was a color contrasting pattern on the walls, then it will be noticeable. The final stage in the preparation is the application of a primer, although many do without this procedure. After that, it is recommended to switch to marking the walls using a level.

Save

It is necessary to draw a vertical line at a distance of a meter from the corner. You can use a simple plumb line or building level and then draw a line. A distance of 1 meter is needed for a wide format canvas, the use of narrower ones requires a different distance. You also need to take into account the future gluing process: the width includes a few cm for fitting. If the wallpaper is end-to-end, then it is necessary to draw a vertical line, taking into account these extra centimeters.

Save

After preparing the walls, it is recommended to cut strips for the entire room. This rule is relevant only for experienced people, but even they try not to cut all the rolls when gluing canvases with a large pattern that requires adjustment in height.

When gluing non-woven fabrics with your own hands, it is important to remember that the height of the room can be unstable throughout the room. Even if a format is chosen that does not require fitting, then you should not cut everything to the same length. First you need to measure the height of the walls in different parts rooms with a step of no more than 50 cm.

When cutting, canvases with a large pattern deserve special attention. The larger the step, the higher the probability of error. For those who are gluing for the first time, it is recommended, if there is a large pattern, to cut off each strip after the previous canvas has been placed on the wall. This will allow you to adjust the pattern without the risk of damage to the wallpaper.

The least problematic in terms of cutting are canvases with a lack of a clear pattern. After checking the height of the room, they can be immediately cut, marking their order with a pencil. If the height error is 1-2 cm and it is planned to use a wide ceiling plinth, then length measurements are not required, this difference will subsequently close.

Save

Non-woven roll materials are a heavy variety of wall adhesive coatings. Many who make repairs with their own hands for the first time make a mistake when choosing glue. For these types of roll coatings, a special glue is required, it says on it that it is intended for non-woven types of wallpaper. It may be of different manufacturers, but the purpose must be the above.

It will not work to glue such canvases on a paste - they will begin to “slide” from the walls. The only exception is fiberboard: if glued to this material, then a mixture of PVA with a paste is quite suitable.

You can properly dilute purchased glue according to the instructions. Granular glue of any manufacturer has dilution instructions. It is usually required to pour the powder into a container with water in a thin stream, stirring the mixture vigorously. It is not necessary to dilute a large portion in advance - with prolonged standing, the adhesive loses its adhesive characteristics, which can lead to the departure of the canvases from the walls. Even the most good glue it is worth breeding again if the work is not completed in one day. In the most extreme case, the remaining mixture should be stored in the refrigerator and used as soon as possible.

How to stick it yourself? Wall cladding process

Save

Often a person wants to glue the wallpaper himself, after briefly watching a video of this process. Even with high-quality preparation, you can stick them illiterately. This is possible in case of ignoring or ignorance of the basics of the location of the paintings.

It is also always worth studying the information on the rolls themselves - sometimes they contain additional individual data on working with them. For example, it is possible to specify a duplicate application of glue on both the wallpaper and the wall. In most cases, it is required to apply it only to the surface to be glued, leaving the canvas dry.

How to glue: technology

The whole process is divided into 3 stages:

1. Applying glue.
2. Sticking.
3. Removal of wrinkles and bubbles.

Save

Before gluing, you need to study the label on the package. Unless otherwise indicated on it, the adhesive is applied only to the wall. It is necessary to do this with a small margin in the bandwidth. Glue is applied separately for each piece of canvas.

After that, the wallpaper begins to be glued from above, trying not to touch the wall with the bottom of the canvas. If do-it-yourself repairs are carried out for the first time, then it is better to call an assistant. It will hold the bottom of the strip, preventing it from sticking to the wall ahead of time.

For a good result, you need to smooth the wallpaper when pasting from top to bottom, trying to avoid wrinkles and air bubbles. If the bubbles remain, then you need to take a rubber spatula or a dry towel and, without strong pressure, direct them to the nearest edge of the canvas. You can also remove minor wrinkles by gently smoothing them out. Large creases require careful detachment of the strip from the wall and re-gluing. This must be done right away.

A narrow metal spatula may be required to detach the canvas from the wall to remove wrinkles or to smear the edge of the wallpaper with glue if it is insufficient or uneven. If glue gets on the front side, it is recommended to immediately remove it with a damp sponge. Only then can air bubbles be smoothed out. Then you can proceed to applying glue for the next piece of fabric and subsequent work.

Knowledge of the general technology of gluing this type of wallpaper does not always save you from mistakes. Often the work turns out to be of poor quality due to an unsuccessfully pasted first strip. Also, errors are likely when pasting the ceiling.

Front page sticker

From correct location the first panel depends on the further result. Do not neglect the level or plumb line at least before you glue the first piece. It is recommended to start from the window or from the corner closest to it. Many people use the window as a vertical line, but this does not guarantee that deviations will not be seen in the future.

Save

The presence of a verified vertical of the first strip does not guarantee the preservation of evenness when gluing with an overlap. In such cases, it is required to regularly unscrew the new vertical and mark it on the wall. Experts recommend doing this for each new strip, but with a good eye, you can skip the canvases through one.

Butt wallpaper sticker basics do not require such nuances for each piece. You need to unscrew the vertical of the first strip and then just continue to evenly position the subsequent ones. But neither this option nor the next one will allow you to avoid fitting the pattern if it is clearly present.

Fitting canvases and photo wallpapers on this basis

Save

Ideally, any pattern is required to be customized, since this type of wallpaper has a relief, it must also be combined to achieve the maximum effect of the uniformity of the wall covering. This type does not require a strong increase in material consumption, while large drawing may force you to buy an extra roll.

On modern wallpaper, manufacturers indicate the size of the adjustment step to match the pattern. The label indicates the number of centimeters laid between the repeating elements of the pattern. To match the pattern, move the blade up or down to cut the next strip.

Wall murals are considered a more complex type of pasting. It doesn't matter what their basis is - paper or non-woven, the gluing process itself requires at least minimal experience. They require an accuracy of drawing alignment literally up to 1 mm, which is difficult to do when working with roll coatings for walls. It is more correct and logical to first paste over the room simple wallpaper by doing a workout. It is better to move on to gluing photo wallpapers, already having a small amount of skills.

Ceiling pasting

If you decide to stick wallpaper on the ceiling with your own hands using rolled non-woven materials, then you need to remember about the correct docking and location of the canvases. There are only two rules:

1. Joints parallel to sunlight.
2. Cloths are located without overlap.

Such requirements have a logical justification - it is difficult to cut the overlap from the ceiling with high quality, and if it is not removed, it will be very noticeable. The same applies to the location of the paintings - the wallpaper should not be glued perpendicular to the window. Otherwise, pasting the ceiling differs little from the walls.

If you set a goal, then learning how to stick such wallpapers with your own hands is not difficult. Each person can do it himself. You need to follow the recommendations and be careful in your work. Then the result will be worthy even without the involvement of highly paid specialists.

Video: do-it-yourself sticking of non-woven wallpaper

Non-woven wallpaper - modern finishing material, well proven. With it, you can bring to life the most incredible design solutions. In addition, they can be pasted over the walls of all rooms of the apartment, including those with high humidity. However, non-standard sizes of wallpaper for Russia (wide sheet size, 2 times larger) and another, different from paper wallpaper, gluing technology, require careful study of how to glue non-woven wallpaper yourself.

Non-woven wallpaper is a multilayer non-woven material made of modified cellulose fibers (70%) and binders (30%), which also contain additives of polyester fibers.

Unlike plain paper, this type of material high performance fire resistance, tensile strength and abrasion resistance. By appearance it resembles paper of a white or yellowish color, in structure - fiberglass, to the touch - elastic fabric.

In the production of tapestries, interlining can be used in combination with other types of wallpaper material: vinyl and paper. In everyday life, it is also customary to consider them as non-woven wallpaper. But these are independent types of wallpaper:

• non-woven vinyl wallpaper;
• wallpaper for painting, where the bottom layer is non-woven, the top one is paper.

Classics are considered light, smooth wallpaper from only non-woven fabric. They will be discussed below.

Advantages and disadvantages

Non-woven wallpaper has many advantages:

• have a huge number of design solutions;
• durable, thanks to which they have a long service life;
• have high moisture resistance, which allows you to do wet cleaning not only of the floor, but also of the walls (can be washed using special tools);
• do not absorb odors;
• dense, easily hide minor flaws on the wall surface (microcracks, roughness);
• vapor-permeable, which makes it possible to paste them over any premises (entrance hall, children's room, bathroom, etc.);
• environmentally friendly;
• do not support open flame combustion (have high level fire safety);
• elastic - stretch when the glued surface is deformed (shrinkage, microcracks, etc.), which is important for newly built houses;
• do not fade under the influence of ultraviolet rays;
• easily removed for replacement
• technological:

1. applying glue to the wall greatly simplifies the pasting process (wallpaper sheets do not get wet from the adhesive mass, which makes it easy to join them and customize the pattern);
2. can be glued on any substrate (concrete, cement and gypsum plaster or putty, wood, drywall);
3. having a width of 1.06 m (standard for Russia), they reduce the number of seams, which reduces the time for gluing tapestries on the wall;

There are also disadvantages:

• high price (the cost of 1 roll is about 1.0 thousand rubles, which makes them inaccessible when repairing the entire apartment for people with low incomes);
• transparency - even the inscription on the GKL shines through them, not to mention the color spots on the wall;
• retain traces of glue that has fallen on the front side.

Surface preparation

Quality and durability of wall finishes modern views wallpaper is largely determined by the level of surface preparation. First of all, this applies to non-woven trellises, although there is another point of view among non-professionals that they can be glued to old wallpaper.

From a technological point of view, such an approach is possible - the non-woven fabric is light and the glue will always keep it on the tapestries that have served their time. But from the aesthetic side, such a finishing option is impossible - through the newly pasted sheets, the old pattern will be very clearly visible, unless of course the previous wallpaper is plain, with a light color scheme.

The whole process of preparing walls for wallpapering is discussed in detail in the work “How to prepare walls for wallpapering”. Let us briefly recall what was discussed there.

Before finishing the apartment with wallpaper, you must perform the following work in sequence:

1. clear the walls old finish and, if necessary, from plaster;
2. repair the formed microcracks, delaminations, shells, etc.;
3. prime the surface;
4. level uneven walls with cement-sand or dry (drywall, plywood, etc.) plaster;
5. putty the surface of the plaster;
6. treat the surface on which the tapestries are glued with a primer.

Tools and materials

Sticking non-woven wallpaper requires the presence in the workplace:

• rolls of non-woven tapestries;
• specialized wallpaper glue for interlining;
• plumb or laser level;
• roulettes for 3 m;
• regulations;
• wide metal spatula;
• a knife with a removable blade;
• a simple pencil;
• hand towels;
• cuvettes for glue or a special mesh for removing excess glue from the roller if it is dipped into a container with glue;
• a pile roller (foam rubber unevenly applies glue to the wall);
• a rubber roller for rolling wallpaper (you can use a special plastic spatula for tapestries);
• cone-shaped roller for processing joints;
• foam rubber sponges;
• plastic bucket for clean water.

Wallpaper preparation

After the type of wallpaper is selected for each room, the color and pattern that fit into the general design decision the interior of the apartment, finishing material is bought. Here it is very important to take all the tubes of the same article and one change of release, so as not to get the problem of different shades in different wallpaper rolls.

Quantity calculation

When calculating the number of rolls needed for repairs, you cannot use special tables, where, based on the perimeter of the room and the height of the ceiling, the required number of tubes is given - non-woven wallpaper has a different width.

The calculation begins with determining the area of ​​​​the walls (the length of the wall is multiplied by the height and all the results are summed up). From the result obtained, the area of ​​\u200b\u200bdoor and window openings is subtracted. The resulting number is divided by the area of ​​1 roll.

With dimensions of 10x1.06 m, the area of ​​​​one tube is 10.6 m 2. However, experts do not take into account the decimal value of the indicator and divide by 10. To the result obtained, 1 roll per room is added for pasting corners, door and window openings and 1 tube for every 6 rolls, if necessary, adjusting the pattern.

Glue preparation

The durability and quality of wall decoration with non-woven wallpaper directly depends on the type of adhesive chosen. He must:

• have good adhesion to trellises;
• diluted to a thick consistency, which allows it to be applied in a thin layer without smudges;
• do not leave marks when dry - do not turn yellow.

Only specialized glue satisfies such requirements - universal even light non-woven trellises hold poorly. We note here that there are two types of special glue: for light and heavy wallpaper.

Attention: heavy tapestries are represented by vinyl with a non-woven backing (vinyl tapestries). Therefore, here we are only talking about glue for light (purely non-woven) types of wallpaper.

Which glue to choose

On the shelves of hardware stores you can see a huge variety trademarks wallpaper glue for interlining. But, due to the lack of reliable information about the quality characteristics of unfamiliar brands, it is better to buy well-known brands.

Most cheap glue from recognizable brands, which is due to Russian origin (250 g package from 200 rubles, 500 g from 399 rubles). Suitable for all types of non-woven trellis, including heavy vinyl wallpaper.

Provides good sliding of a sheet of wallpaper on the wall during docking. Contains additives against mold and fungus. Can be stored undiluted for up to a week. At the same time, it also has disadvantages:

• poorly bred - it is difficult to obtain a homogeneous mass;
• not suitable for tapestries with a three-dimensional pattern - it requires tight rolling, which cannot be done with a rubber roller on embossed wallpaper (a wallpaper spatula cannot provide such an effort).

A product of the famous German company Henkel. It is made from methylcellulose and natural resins, which provide reliable adhesion of all types of non-woven wallpaper with various types walls (drywall, concrete, cork, brick, etc.). Easily bred.

Does not leave stains when it gets on the front side. It has an important feature: it must be diluted to a more liquid consistency than indicated on the package, as it dries quickly. It is in the middle price category - a pack of 250 g from 290 rubles. up to 350 rubles, a package weighing 500 g from 535 rubles.

"Quelyd Special interlining". Produced in France. It has the highest price among all brands of glue for non-woven wallpaper (a package of 450 g costs from 360 rubles). However, the price is fully consistent with the quality - professional finishers consider it an ideal tool for gluing tapestries:

• perfectly holds light and heavy wallpapers, with a smooth and voluminous pattern;
• easy to breed;
• does not smell;
• does not flow down the wall during spreading;
• does not leave marks when it gets on the front side, etc.

The PUFAS range of adhesives for wallpaper with non-woven base (5 types on sale) provides better adhesion between the tapestries and the wall surface. It has a color indication, which helps with spreading - no gaps are allowed. When buying glue of this brand, you can choose a product for specific wallpapers: smooth, corrugated, light, heavy.

How to calculate the number of packs of glue

An important feature of the glue for non-woven trellises is that the packaging indicates its consumption not for the number of wallpaper rolls, but for the wall area in m 2. Therefore, the calculation is made a little differently.

First, the area of ​​\u200b\u200bthe walls to be pasted is determined. Then the result is divided by the consumption in m 2 indicated on the package. The result is rounded up.

How to breed

To dilute the glue you will need:

• capacity for 10-12 liters (plastic bucket, basin or bowl);
• warm (40-45 ° C) water (it will not dissolve in cold water, it will curl up in insoluble lumps in hot water);
• an object with which you can stir the glue (stick, whisk, mixer, electric drill, etc.);
• a tablespoon or measuring cup (an error of only 50 g of powdered mass leads to a complete marriage - the mixture is poured into the toilet).

The instruction is simple:

1. poured into a basin (bucket) warm water in the amount specified in the instructions - no more, no less;
2. the required amount of the powdered mixture is measured;
3. water is stirred until a funnel is formed with a stick or hand (power tools cannot form a funnel);
4. glue slowly pours into the center of swirling water;
5. in this way, the glue is stirred for another minute after the entire dry mixture has been in the water;
6. further stirring is desirable to carry out with a mixer or a drill with a nozzle - they will break all the small lumps, which is difficult to do manually;
7. after the end of stirring, the glue is allowed to brew and swell (14-16 minutes is enough), during which time it will take on a working consistency - it will look like jelly or thick sour cream.

Professional finishers recommend adding another 200 ml of water and mixing thoroughly (thick glue dries quickly). Water must be added within half an hour after the start of stirring. If you violate this requirement, you get water with floating jelly-like clots. Everything, on this the resulting glue is ready for use.

Pasting instructions

How to glue non-woven wallpaper with your own hands? Step-by-step algorithm of work:

• In the room where the work will be carried out, one day before they begin, airing is done, after which the windows and doors are tightly closed;
• The height of the wall for pasting is measured;
• Wallpaper sheets are cut to size or with a tolerance of 8-10 cm;
• Wallpaper glue is being prepared;
• The place to start work is determined - this type of wallpaper allows you to start work from anywhere, but it is better from a corner, stepping back 4-5 mm;
• A vertical line is applied to the wall for gluing the first sheet a few mm from the corner;
• The surface of the wall is smeared with a roller or brush with a thick layer of glue slightly wider than the size of the tapestries;
• The first sheet is glued with an edge strictly along the applied line;

• With a roller or wallpaper spatula, the canvas is rolled against the wall. Movements go from top to bottom, from the center of the sheet to its edges. When glue appears on front side trellis, it is removed with a foam sponge;

• The next sheet is glued end-to-end (beginners can overlap wallpaper without a pattern - the seam is then cut with a knife and an inconspicuous connection of two sheets is formed). If the wallpaper did not lay down the first time strictly vertically or the pattern did not match, the tapestries can be torn off the wall and glued again - the material will not tear or stretch;
• Excess glue and air are removed from under the wallpaper with a rubber roller. Since the interlining stretches a little, it is necessary to ensure that during rolling the edge of the web does not go over the previous sheet. The joint is rolled with a special narrow roller. If the edge of the wallpaper still lags behind - the glue has dried, then the wallpaper is removed from the wall, and it is re-smeared with glue.

Problems arise in the corners, due to the large width of the trellis. How to glue non-woven wallpaper when passing corners? Here the techniques are the same as when working with narrow trellises:

However, there is one caveat here. The cut off part of the wide wallpaper is not thrown away, but serves as the next sheet when pasting the corner, even if the width of the cut off part of the tapestries is only 15-20 cm.

The issue of passing corners is considered in detail in the work "".

How long does non-woven trellis dry

Many apartment owners tend to ventilate the pasted premises immediately after the completion of work. However, this cannot be done - drafts will lead to peeling off the wallpaper at the joints and in the corners, the most problematic places.

How long can you ventilate the room after finishing work? To answer, you need to figure out how long non-woven wallpaper dries after gluing. Manufacturers of non-woven tapestries write that their complete drying occurs within 12 hours. Practice refutes this statement - the wallpaper dries for 24-28 hours.

Attention: do not confuse with the drying time of non-woven wallpaper. It can be up to 3 days.

Finally

As can be seen from the above material, the difference is how to glue non-woven meter wallpaper do-it-yourself and narrow trellises - no. There are deviations only because of the material from which the wallpaper is made.

Related videos