Close the pipes in the combined bathroom. How to close the pipes in the toilet? Facing the box with ceramic tiles

03.03.2020

Any toilet is always an accumulation of a wide variety of pipes, risers, and faucets that form a communication network that is directly responsible for the comfort of our lives. But despite such an important mission, all these devices have one significant drawback - their unattractive appearance, which can ruin even the most sophisticated interior. It is impossible to remove communications - it remains only to fight their unpresentability. How? There are many ways to hide pipes and related equipment, but we will focus on best projects- we tell you how to close communications with PVC panels, roller shutters, drywall and tiles without any hassle.

Available plastic panels

PVC sheets are one of the cheapest and easiest ways to mask pipes in a washroom. Due to its flexibility and low weight, plastic is easy to use, so it will not be difficult to build a false wall out of it. For installation work you will need:

PVC panels 8 mm thick;
metal or wooden planks;
hacksaw;
scissors for metal;
drill;
screwdriver and self-tapping screws with press washers;
level.

PVC panels

Work begins with markings - mark on the walls, ceiling and floor where the frame strips will be attached. The latter should not come into contact with the pipes - a distance of at least 5 cm must be maintained between the frame and communications on all sides. Then, using self-tapping screws, fix the frame strips, wooden or metal, with an average step of 30 cm. and floor planks.

When the frame of the box is ready, install the starting bar on the lower profile and start sheathing the “skeleton” with panels. The first sheet must be inserted from the corner into the starting bar and secured with self-tapping screws with press washers. Install the second and subsequent sheets on the frame with a tight fit with the previous panels. Finally, close the edges of the sheets and the corners of the false wall with skirting boards, and then seal all joints with sealant.

Advice. In two or three panels, depending on the dimensions of the false wall and the nature of the location of the pipes, make in advance a kind of inspection door for servicing communications.

Practical roller shutters

Roller shutters are the most practical way to hide communications, as they always provide unhindered access to pipes for their maintenance. You can mount this kind of blinds both on the entire wall, and in separate blocks. But you should be aware that installing roller shutters is not an easy task, so strictly follow the manufacturer's instructions that come with the installation kit.

Prepare for work:

roller shutters with mounting kit;
level;

roller shutters

drill;
roulette.

Advice. Before mounting the roller shutters, it is desirable to align the walls so that there is exactly the same distance between the blinds blocks.

The frame of profiles is installed first - the gaps between the slats should correspond to the width of the roller shutters. Then guides are attached to the side rails, and a box of blinds to the top. Further to the drum shaft, using the manufacturer's fasteners, lamellas are installed with mandatory fixation in the grooves of the guides. After installing the last lamella, the process of opening / closing the roller shutters should be adjusted.

Diverse drywall

Drywall is good, first of all, because it lends itself to almost any processing: a finished false wall can be painted, wallpapered, painted, plastered, decorated with mosaics, etc. Thanks to this, you get the opportunity not only to hide the pipes, but also completely change the look of the toilet room.

To make a false wall you will need:

moisture resistant drywall;
inspection rubber hatches with a magnetic lock;
fixing canopies;
steel profile;
self-tapping screws and dowels;
drill and screwdriver;
putty;
hacksaw;
level;

Drywall box

insulating tape;
reinforcing mesh;
finishing material.

Installation diagram of a plasterboard false wall:

Mark out the work site - mark the lines for the frame on the walls, floor and ceiling. Fasten the canopies along the marked lines, and install profiles on them - starting from the floor and gradually moving along the walls to the ceiling. Then install the extension profiles for the racks, fixing them in the ceiling and floor strips. Fix both canopies and profiles with self-tapping screws.
When the frame is mounted, start installing drywall - fasten the sheets to the profile strips with self-tapping screws in 20 cm increments.
Close the gaps between the sheets with putty and reinforcing mesh - the latter will protect the seam zones from cracking.
After completing the sheathing, make two or three holes in the plasterboard wall for inspection hatches and install the latter in the resulting openings.
Treat the false wall with putty and complete the finishing cladding.

durable tile

- a traditional material for a bathroom, but to mask communications it is used not only due to the classic look, but also due to durability. If we exclude the possibility of mechanical deformation, then good tile can serve in the toilet room for more than one or two decades without becoming moldy and without losing its appearance. The tiles are mounted on a special box made of plywood or drywall - it is attached to the frame, similar to the previously considered options for the construction of false walls. Do not forget to also install already familiar inspection hatches in the box.

Advice. The material for the tile box must be strong enough to support the weight of the finish, so use plywood or drywall sheets that are at least 12mm thick.

For direct tile laying, prepare:

ceramic tiles;
tile cutter;
tile adhesive;
notched trowel;
sealant;
tile crosses.

First, mix the adhesive and prepare the tiles - cut the products to the configuration of your box. Further, moving from the bottom corner, start finishing the box according to the following scheme: with a spatula, apply the adhesive on the working surface of the box; moisten the mounting side of the tile; lean the tile against the work surface and press lightly. Insert plastic crosses between the tiles to ensure even seams. After laying all the material, remove the crosses, and treat the seams themselves with sealant.

Here are four spectacular ways to hide the "web" of pipes in the toilet room and make its interior as harmonious as possible. Panels, drywall, tiles, roller shutters - all these masking options are easy to perform, financially affordable, and attractive in appearance. The instructions are in front of you - it remains only to make a choice, and you can safely take on the transformation of the bathroom.

Plastic box in the toilet: video

How to close the pipes in the toilet: photo

Making repairs in the toilet, the owners strive to ensure that it is functional, practical and beautiful. If there are usually no problems with the floor, side walls and ceiling, then the back wall, in which the pipes are located, makes owners and builders think. How to close the pipes in the toilet so that they are invisible, but at the same time easily accessible? In order to deal with this issue, we compare the advantages and disadvantages building materials, as well as how easy and quick to mount structures from them.

Advantages of different materials

Options for how to close sewer pipe, is actually a lot. You can hide pipes that distort the aesthetic taste behind a drywall box, install blinds or plastic panels.

The easiest way to hide pipes in a toilet is to cover them with a drywall box. This material has the following advantages:

Easily dismantled if necessary.
The drywall construction is easy to install.
Does not highlight harmful substances even if it gets very hot.
It is environmentally friendly and does not harm human health.
Convenient for subsequent decorative finishing. It can not only be tiled, but painted and glued.

The disadvantage of drywall is that if you need to repair or change pipes, then the box will have to be completely dismantled and rebuilt from new materials.

In order to hide the pipes in the toilet, plastic panels are well suited, which have the following advantages:

Easily mounted on the frame.
Safe for human health.
Provide access to pipes in an emergency without requiring complete dismantling of the wall.
They have a long service life.
They are not afraid of moisture and are hygienic.
Quickly dismantled in case of urgent need. For example, when carrying out a new repair.

The disadvantage of plastic is that it can stand out strongly against the background of the side walls. Therefore, you will have to carefully select the plastic to match the color of the tiles or wallpaper.

Blinds are well suited for small toilets. This is the most cheap option close the pipes. Blinds will allow:

Save space.
Easy and quick to close the back wall.
Close the rear wall completely or partially.
Provide quick access to water meters or pipes.
Place shelves in the niche for storing household equipment and cleaning products.

Lack of blinds - can quickly turn yellow or darken. Therefore, they must be mounted in such a way that it is possible to replace them with new ones at any time without making a new repair in the toilet.

The box, which is no less often used to hide pipes in the toilet, also has its advantages:

If it is ready, then it remains only to mount it.
If the features of the back wall do not allow you to purchase a finished box, you can make it yourself. There are no special difficulties, if it is not multi-level, with its installation.
This is usually a removable design.

The disadvantage of the box is that it is often a very voluminous design. In the event of an emergency, it is not always possible to quickly remove the box.

Mounting methods for various structures

The principle of mounting the structure for the subsequent closing of pipes in the toilet is simple. Even an inexperienced builder can build such a structure. The basis of the structure is made of a metal profile or wooden bars. Then, depending on what will be used to mask the pipes, it is sheathed with the appropriate building material - in whole or in part.

If the pipes are closed with a box, the structure can be sheathed plastic panels, sheets of waterproof plywood or drywall. Usually glued to drywall tile. This is done so that the back wall does not stand out against the background of the side walls and the tiled floor. The box can be bought ready-made and mounted on the back wall of the toilet. But this option can be more expensive than making a drywall or plywood box. And you have to tinker with the pipes connected to the toilet.

The box can be of several configurations:

In the form of a false wall. If the toilet is small in size, then it is better to make the toilet hanging. Access to pipes due to a false wall will be difficult.
Square. If the risers are in one corner. The window is made at the level of valves and counters, which gives access to them at any time.
In the form of an oblique false wall. It is done at an acute angle to the back or one of the side walls. With such a box, you can close thinner pipes that extend from the side of the main riser. Mounting the box on the entire wall in this case does not make sense - you can just “bevel” the one that already exists a little.
Multilevel. It is mounted if the pipes in the toilet are located so that in order to close them, you will have to fence off half the space of the toilet. Such a box closes at a certain height a specific part of the pipe or pipes.

The rear wall can be fully sheathed with plastic panels. They are mounted on a special frame using metal profiles or wooden bars. First, markings are made on the back wall. Then profile guides are attached. After that - the profiles are installed on the side walls - a frame for the panels is obtained. The profiles are attached to the walls with dowel-nails and a perforator. The distance between the fasteners should be 30–40 cm. After the profile is fully assembled, panels are attached to it using self-tapping screws.

If the box is made under the blinds, then its main part is mounted to the ceiling. At the same time, the back wall can be closed with blinds completely - from ceiling to floor or partially. If the blinds partially cover the wall, the box will have side panels.

Whatever the back wall is sheathed, it is imperative to plan an opening window for access to the pipes. The window may be different sizes. It must match the design and provide full access to pipes and meters.

Design choice

Each of these materials has its own advantages and disadvantages. So what is the best way to close the pipes in the toilet? It is necessary to choose the material based on the general design idea and the means available.

If there is little money, it is better to stay on blinds or plastic panels. Lay tiles on the floor, paste over the side walls with wallpaper. And sheathe the back wall together with the ceiling with plastic panels or close the blinds.

If the owners are not constrained by funds, then the toilet can be fully tiled. And cover the pipes on the back wall with drywall.

In any case, how to hide the pipes on the back wall is up to the owners. Regardless of which building material they stop on, it should be remembered that before mounting the frame and its sheathing, it is necessary:

Replace old pipes with new ones.
Make sure there are no defects in the pipes.
Fix defects if they are found.
Make sure that tees, angles, couplings and other transitional elements are made of the same material as the pipes - this will reduce the likelihood of emergencies in case of temperature changes in the pipes.

And what material or method did you choose to hide the pipes in the toilet? You may have already had to do repairs in the toilet more than once, and there are tricks. If so, please share with us.

Photo

Video

This video shows how to install roller shutters in the bathroom:

This video will show you the steps of a bathroom renovation. You will learn how to close the pipes with drywall in the toilet:

On a relatively modest area of the toilet, there are always many sewer interchanges. Any technical components do not look aesthetically pleasing and give the impression of an unfinished repair. Therefore, the question often arises of how to hide the pipes in the toilet and give the interior an attractive look.

Where to begin?

Before hiding the pipes in the toilet, you need to carefully inspect the riser and other communications for damage, repair them if necessary. It is necessary to start preparing drawings and calculating the material for the future design after all technical issues have been resolved. For an accurate calculation of raw materials, it is necessary to carefully make all measurements of the area on which the work will be carried out.

Hardware stores offer a wide range of finishes, but whatever you have to work with, you will need the following tools:

screwdrivers;
drill;
screwdriver;
building level and tape measure;

a saw for plastic or a knife for cutting drywall;
scissors to cut metallic profile;
self-tapping screws and fasteners for the profile.

Material selection

If you need to hide communications quickly, PVC panels will be the best choice. This is a cheap and versatile finishing option. The main thing is to choose a color and pattern that will harmoniously fit into the overall picture of the interior.

Plastic panels have several advantages:

safe for health and the environment;
installation of panels is not difficult;
installation is possible in the shortest possible time;
acceptable price;
the ability to install a hatch for access to meters or places where a leak may appear;
the possibility of creating a structure consisting of separate parts;
no additional finishing required.

And also quickly and inexpensively, you can close the riser with drywall. The toilet does not have as high humidity as the bathroom, but it is better to use a moisture-resistant type of material.

Drywall has all the advantages of panels. Unlike them, this material requires additional finishing. But such a disadvantage can be regarded as a virtue: drywall without finishing can be used for tiles or any other decorative trim. Thus, the wall behind which the pipes are located will be indistinguishable from other walls in the toilet.

Design options

The design that will hide communications is selected depending on several factors:

the size and nature of the direction of the pipes;
the location of the pipes relative to each other;
the presence of auxiliary devices and cranes;
general environment in the room.

After analyzing these features, it will not be difficult to determine the type of future design. The most common are several popular types.

box

It is a simple design that even a beginner can handle. The frame is created from a metal profile or wooden slats. Next, the base is sheathed with the material that was chosen. Full or partial sheathing is possible, depending on the availability of metering devices or taps near the riser. In this case, you must leave the window so that you can access them.

The frame of the box can be sheathed with PVC panels, moisture-resistant plywood or drywall. Drywall is usually decorated with the same materials as the main walls. Exist ready-made options boxes. But this option may be more expensive. Making the box yourself, it is possible to immediately take into account all the nuances. While the finished box will have to be customized to the desired parameters.

The design of the box is represented by several configurations.

false wall. Good decision to hide several pipes located nearby at once. It looks aesthetically pleasing, but takes up a lot of space.
Square. Can be positioned both vertically and horizontally fan pipe. Suitable for rooms in which pipes are located in the corner.
Oblique false wall. The middle option between the previous ones. The design is attached at an acute angle to the side or rear wall. Just like a false wall, it allows you to hide several pipes, but saves a lot of space.
Multilevel. It is installed in the case of a chaotic arrangement of pipes in the toilet. To save space, boxes are created in places where communications are located.

Built-in sanitary cabinet

The design with doors on the wall behind the toilet is called a sanitary cabinet.

Using this method of masking, several problems are solved at once.

An additional niche for shelves appears, on which cleaning products and accessories can be stored.
The presence of doors does not impede access to meters, filters, manifolds and pipelines.
In the event of a pipe break, the cabinet will not impede access to the accident site. Replacing metering devices in a toilet with a sanitary cabinet will not be inconvenient.

The choice of material for the manufacture of doors is quite large. Plywood, PVC panels, chipboard, metal, wooden or glass doors are especially popular. You need to choose a material that will fit into general style interior. For example, in a toilet decorated with plastic, plastic doors would be appropriate. And for the suburban wooden house wooden doors are suitable.

Do not forget about the convenience of the location of the doors in the locker. They must be located at a suitable height so as not to obstruct access to the desired junctions. Handles on the doors should also be suitable.

The installation of swing doors in a sanitary cabinet takes place, like any other doors, they are fixed on hinges to the base. Ordinary doors are suitable for a spacious toilet. Closer rooms are best equipped with compact accordion doors, sliding models or curtains.

Concealed installation - chasing

Chasing is an alternative to decorative types of pipe masking. With hidden wiring, it is supposed to sew parts in specially punched ditches, which are called strobes. Such technological holes are made using a wall chaser or puncher. Pipes hidden in the floor screed also belong to hidden gasket. In this case, the wiring is poured with a concrete solution.

The main advantage of this type of disguise is aesthetics. Communications are completely hidden in the wall. With the exception of the riser, the diameter of which is too large and cannot be embedded in the wall. The advantages include the complete safety of pipes, their damage during hidden installation is impossible. Significant space savings is also a plus.

Weak side method is considered to be laborious, costly and inaccessible pipes. You can sew up the pipes yourself, but you will have to study a lot of literature in order to get it right. The use of hidden installation is not possible everywhere. The method will be good in private houses built of brick or solid blocks, as well as in high-rise buildings with walls of increased thickness. In other places, this method will run counter to SNIPs. Gates significantly weaken the load-bearing walls, which are already heavily loaded.

Some requirements can significantly complicate the installation:

only one-piece pipes can be sewn up, others need free access;
in the wall on which the work will be carried out, electrical wires should not pass;
it is necessary to take into account the linear expansion of the pipe material;
you have to use clamps in order to have good sound insulation.

We hide beautifully

It is not always convenient to close pipes with auxiliary materials. In some cases, there is not enough space for complex structures, or time to repair the toilet may be limited. Sometimes pipes are easy enough to decorate when we close communications with a partition, access to them is difficult, and this can be inconvenient.

Outdoor placement of communications

Pipes can be left in plain sight and not decorated, if they look beautiful on their own. For example, metal communications in combination with sanitary ware from the same material are perfectly combined and fit into the interior of a loft, techno or high-tech style restroom. In a toilet with such an environment, they will become a source of pride. But such pipes are expensive, in addition, there is a chance of getting burned.

Therefore, you can beautifully beat ordinary communications:

cover with paint suitable for the general color scheme toilet
decorate with unusual patterns, while you can use special stencils;
sheathe with beautiful pebbles, braid, glass;
disguise with artificial plants or make the pipes themselves in the form of trees: the toilet will resemble an impenetrable jungle or dense forest;
glue the pipes with various stickers or stickers;
if you get creative, you can use material that is usually recycled, such as metal caps from carbonated drinks, and in addition to unusual design pipes it would be appropriate to make a small panel of the same material.

Decorating pipes is a convenient way to hide communications. All parts of communications are in plain sight, you can always check their condition and, if necessary, repair or replace.

Blinds

Disguise thus resembles a false wall. But not a wall is created, but a curtain. It can be rolled up if necessary.

Blinds Benefits:

closing pipes in this way saves a lot of time;
during installation, a lot of garbage is not created;
long service life of blinds;
the price is small;
the niche formed behind the blinds is convenient to use for storage;

the design is compact both in open and closed form, it will not interfere, however, open blinds provide full access to counters and taps;
the choice of material is very large: from inexpensive and versatile plastic to expensive and specific wood and metal, but due to high humidity, fabric options are not recommended for use in the toilet;
the assortment is replete with a variety of colors and patterns, it will not be difficult to choose the right ones;
in case of damage or loss appearance there is no need to replace the entire structure, it will be enough to replace the damaged lamellas;
they can replace the screen under the bathroom or become a partition that closes washing machine if it is located in a niche.

Often pipes, meters, plumbing boiler spoil general form bathroom or toilet. You can decorate your bathroom in a variety of ways. You can beautifully remove the technical unit with your own hands by choosing the right way.

A sewer riser, water heater or bathroom meter has nothing to do with the aesthetics of the room. That's why so many people want it. You can do it, but it's important to know how to do it right.

Ways to mask the riser in the bathroom:

Construction of a false wall;
Use of plastic panels;
roller shutters;
Plasterboard or plastic box;
Household locker.

False wall is considered the most drastic way to sew up the back with pipes. The material for the wall will be plywood or chipboard. Often the wall can be sheathed with drywall. Before work, pipes should be prepared, rust removed and painted. For the frame, galvanized profiles are used. They are attached to the floor and wall. The material is attached to the frame with self-tapping screws.

For a separate toilet can be patched up wooden frame instead of galvanized.

Often, plastic panels are used for the bathroom. They have a number of advantages: resistance to moisture, strength, lightness, low cost. At the same time, the installation of the material is simple and does not require additional painting. The panels have an air chamber, which makes the material soundproof.

More in a simple way the use of roller shutters is considered. They are installed and operated like ordinary blinds. At the same time, new developments provide options with sound insulation or heat saving.

The box is made from a metal profile, which is sheathed with plastic. It can be removed, which is very convenient. The box has an inspection window. We hide the hatch under the tile. This is a kind of window for access to pipes. An excellent option is considered a utility closet. So you can not only hide the pipes, but also get a place to store household chemicals.

Options: how to make a pipe box in a drywall toilet

The location of the pipes also determines the masking option. So you can hide the entire wall or place with communications. The first skin is considered more aesthetic. The box is mounted in two ways. The first involves the use of a framework. This gives strength to the skin. The second option is frameless.

Before work, you should make a plan of the room with the location of all pipes. You will need to calculate the amount of material and prepare the necessary tools.

For the bathroom, it is better to use moisture-resistant drywall. It is resistant to the appearance of fungus, environmentally friendly, guarantees sound insulation. The material can be used for both horizontal and vertical communications.

Making a drywall box:

It is required to retreat 2 cm from the counter and pipe and draw vertical lines on both sides. Then fix the profile.
We attach drywall sheets.
Joints should be puttied and hidden with a decorative plinth. The surface should be painted over.

Other material is also widely used for the box. So the lining is made of plastic. Expanded polystyrene has many advantages, it is considered to be an ideal option for the bathroom.

How to close the pipes in the toilet with plastic panels

First you need to prepare the frame. First, measurements are taken. It should be borne in mind that in addition to sewage, the toilet contains water pipes. With the help of a tape measure, all manipulations with measurements are performed. On the created plan, all fasteners and the main elements of the skin should be indicated.

Before masking the pipes, you should check their condition. If necessary, communications are replaced.

Then the frame is attached to the surfaces. To the bottom and top should be screwed wooden slats or profile. Then they are mounted every 30-40 cm. Frames with doors should be located on the frame. They should be fixed at the end of the base.

How far should the toilet be from the wall? Look for the answer on the following page:

Stages of sheathing the frame with plastic panels:

Closing begins with the starting molding. The element is attached to the frame with self-tapping screws. To hide the heads of the fasteners, the self-tapping screw must pass through the shelf that the next panel overlaps.
Next, lay the next panels, placing them in the grooves. The free end of the panel is fixed with a self-tapping screw. This is how all panels are installed.
Doors are installed in the wall.
A molding is also mounted on the opposite side. All joints are processed in the same way. Ventilation must be provided in the box.

Fasteners can be not only self-tapping screws. Cleimers, clips, glue are widely used. The main thing is that it is fashionable to remove the mount if necessary.

Creating a toilet door behind the toilet: simple and useful

A simple option on how to sew up pipes in a toilet: stylish blinds

With the help of blinds, you can quickly and easily hide an unwanted technological unit. This is an aesthetic choice. Blinds have many positive aspects.

Benefits of using blinds:

Installation is simple, easy to do yourself;
Do not take up much space, suitable for small rooms;
Provide free access to pipes;
A wide range of different options;
Simple repair.

Pleased with the durability of the material and affordable cost. For bathroom and toilet ideal option will be aluminum or plastic blinds. Wooden curtain for rooms with high humidity unsuitable.

Also for the bath and toilet use plumbing blinds. This is a stylish and neat option. Often on the market you can find blinds with photo printing. At the same time, a niche is created inside where it is convenient to store household items.

Ways to close the pipes in the toilet (video)

Decorating plumbing in the bathroom is considered a particularly scrupulous task, especially in Khrushchev, where there is little space. The disguise may vary. Termination can be done using a false wall, PVC panels, blinds or a cabinet with shelves inside and free access to communications. Decorative materials also varied. The use of plastic, drywall, fiberboard is very popular.

Toilet space is limited. The piling up of communications makes the already small space heavier.

Even beautiful tiles are lost against the background of pipes. Many owners prefer to hide unsightly elements from prying eyes.

The range of building materials allows you to choose options for any budget. Next, consider the most common ways to close the pipes in the toilet and get acquainted with the photo designs.

Material Requirements

The toilet is a room with a specific microclimate. Therefore, before you hide the pipes in the toilet, decide on the material.

It must meet such important criteria as:

Moisture resistance. There is constant condensation in the toilet. Water droplets settle on surfaces. Over time, unstable products begin to soak, fungus and mold appear. Therefore, wiring should be sealed with products that are resistant to high humidity.
Strength. You constantly need access to meters and ball valves. For this, special hatches are installed - they will not withstand them with a fragile structure.
Aesthetics. Another important criterion. It is better if the product is combined with the overall finish of the toilet.

Close the pipes in the toilet with plastic panels - instructions

The thickness of the lining usually does not exceed 1 cm. Its width varies from 15 to 50 cm. The standard length is three meters. The most common size is 20-37 cm.

An extensive range of colors makes it easy to make a choice for a specific design solution.

To decorate the fasteners of the lining around the perimeter or in the docking areas and corner parts, moldings are used various shapes. They are dyed in White color and they go great with any color scheme.

To mount the lining, you do not need to have a lot of tools (which ones you will need, read below), the usual ones are enough for finishing metal and wood.

By heating the panels are given any shape. They are well bonded with glue and welded. They can sew up the wall at any angle of inclination. If the box is made and sheathed correctly, then the presence of the pipeline will be invisible to others.

It has already been said above that wooden beam for a room such as a bathroom or toilet is not good choice. Since the room is damp, which will have a negative effect on the wood. Even with protective solutions, the desired protection indicator is not achieved.

Modern production offers a wide variety of galvanized steel profiles and fasteners for them. To hide the pipes in the bathroom or toilet take a special profile. Its standard length is 3 - 4 meters. The transverse dimensions are 20 x 20 mm. But they can be more.

Features of work

At first glance, it seems that it is not difficult to close the pipes with a plastic clapboard. But many, starting this work, do not always have about it. clear view. Namely:

Before you hide the pipes, you need to check their condition. It may be that they need a replacement. And such a problem should be solved before starting the skin. Because emergency situation may occur after the entire structure is assembled, and then the structure will have to be dismantled. Old steel and cast iron pipes. These are high-strength and reliable building materials, but upon careful examination, cracks and chips can be revealed, which soon grow into big problems.
After the issue with the pipes is finally resolved, it is necessary to accurately determine the shape of the structure that will close them.

Pipes do not take up much space. And the dimensions of the overall concealing structure depend on where the pipeline is located. After all, the riser can be located in the corner, but it happens in the middle. Wiring running horizontally is most often located close to the floor.

We must not forget about the valves, metering devices, etc., you need to make hatches to access them.

If the pipes pass in niches, then it is advised to close such places with a false wall, or to make an L-shaped structure.
Horizontally located pipes must be closed with a rectangular threshold. In the area of the sink, the threshold must be raised to its height, and the empty space must be used to equip the shelves.

When all these points are thought out, you can take care of building materials and the necessary tools.

Tools needed for sheathing:

building level;
knife (for mounting actions);
profile (starting and guide);
screwdriver and screwdriver;
panels.

It should be noted that the glue in this situation is not one of the the best options, because the need to disassemble the building may appear at any moment. From this point of view, it is advantageous to use self-tapping screws.

The use of plastic panels

Before you sew up the pipes in the toilet with plastic panels, you will have to construct a false wall. The instruction for its device is as follows:

execution of markings in the area of \u200b\u200bthe ceiling and floor. Fastening guide profiles to the floor and racks on the walls.

rack profiles are fixed in the corner parts of the structure;
with a half-meter indent, profiles are mounted transversely, otherwise the building will not be rigid:

frame sheathing.

The video provided details the work. Here the process is described in detail, and any novice master can cope with this task.

Having carefully studied the information provided, you can not only close the unsightly pipeline, but also create a beautiful decoration of the room.

Features of marking

First, the contour is applied on the floor. How correctly the corners are observed, you need to check with a square. After checking for accuracy, the contour can be transferred to the ceiling.

A rack profile is mounted on the corner parts of the box. Its vertical position needs to be checked. building level, while a dot is placed on the ceiling, this is a projection of the contour made on the floor.

IMPORTANT! For exact matching of the mark on the ceiling and on the floor. Before marking, it is necessary to check how accurately the floor is horizontally located.

Frame installation

To sew up the pipes in the toilet with plastic panels, you can’t do without building a base. Such a design is needed not only when working with lining, but also for sheathing with other materials.

It should be noted right away that experts call a galvanized metal profile the most suitable mount for plastic lining. It provides the desired stiffness indicator, and its protective treatment saves metal from corrosion formations.

Many, in order to close the system, take ordinary wooden bars instead. But, this option is not considered the best, because the wood should be treated with an antiseptic. Also, in this embodiment, fire safety becomes much lower.

To close the pipes in the toilet, you need to prepare a plastic crate. In this option, the panels must be mounted using special clips. But, such a frame has a big drawback, it is characterized by low rigidity.

The construction of the frame begins with fastening the profiles to the floor. Behind them are mounted racks running in a vertical direction. Transverse ribs are placed at the very end. Profiles are fastened with self-tapping screws to each other.

When working, you should carefully monitor the size of the gap between the ribs of the frame. When the plastic panels are located from the bottom - up, then the distance is approximately 60 - 80 cm. When they go transversely, it may be necessary to install an additional rack.

IMPORTANT! We must not forget the fact that a window should be left near the revision and fittings. It will be required to access the system. Its location of this window is advised to consider during the construction of the frame.

Structural paneling

To close the sewer pipe, it is necessary to strengthen the panels on the mounted base.

A starting molding is installed near the wall. It is attached to the profile with self-tapping screws. This fastener is carried out through the shelf, covered by the next plate. Thus, the head of the self-tapping screw on the plastic casing will not be noticeable.

At furniture companies, they will select a product of the required color and texture. To hide the wiring, a wooden beam is installed on the side walls of the opening. Then, with the help of hinges, doors are installed. It is possible to make a sliding structure. To save money, a cutting board is used.

Masking with chasing

Decoration techniques:

You can not hide, but simply paint. The color should be in harmony with the overall design of the bathroom.
Using stencils, original patterns are applied. A little patience - and interesting stories will appear on boring pipes.
As decorative elements different pieces of glass, pebbles or ordinary sewing braid will do.
Can be braided with artificial flowers. The design will be close to eco-style.
Stickers and decals are also an option. If pasted over with newspaper or magazine clippings, they will resemble cabinets with posters. Get stylish and unusual.
Plumbing elements can be wrapped with twine or other similar elements.

The owners do not always seek to repair communications. Sometimes plumbing communications become part of the interior. Fans of high-tech or loft style will be able to appreciate this design. Most good combination- copper plumbing and the same pipes.

The external pipeline is installed much faster. And there will be no problems with the repair. You can always replace worn parts.

Metal products need careful care. A significant disadvantage is the price. In addition, the metal heats up quickly. Contact with it can result in severe burns.

The arrangement of the bathroom requires a special approach. Materials must be durable and meet sanitary standards. There are plenty to choose from. It remains to determine your preferences. There are no strict limits. Each option is easy to recycle at your discretion. It all depends on the area of \u200b\u200bthe room and the imagination of the owner. Based on these options, it is really possible to create your own camouflage method. Dream boldly, and entrust the realization of fantasies to professionals.