I think many will be interested to know more about the submersible pump Vodome, I will give you this opportunity in the form of a question - answer. There is little experience in answering these questions, questions were asked by our customers and after which this article about Vodomet pumps was compiled.
Question: Where is the multistage submersible centrifugal pump Vodomet (hereinafter Vodomet) used?
Answer: The water jet pumps water from a well, a well, from open water sources and delivers water through pipes for further use. Suitable for organizing an automatic water supply system in country house and for irrigation.
Question: What is the design of the submersible multi-stage centrifugal pump Water cannon?
Answer: The water jet has a hydraulic part and an electric motor. The hydraulic part has impellers, diffusers and shafts, while the electric motor has a stator and a rotor. Water is taken from the bottom of the pump, water enters through small filter holes. The water cannon is completed with a special cable and plug for connecting to the mains.
Question: What is the minimum inside diameter of the supply line in a Vodomet submersible pump?
Answer: The value of hydraulic resistance depends on the diameter of the supply pipe, the smaller the diameter. the higher the resistance. Minimum Diameter supply pipe for all submersible pumps must be at least 1 '' - 25 mm. When the diameter is narrowed and the flow through the pump is less than 10 l.min. you risk overheating the pump and it will burn out.
Question: What is the minimum depth of the Water Cannon in the water?
Answer: The pump can be lowered to a minimum depth of 15-20 cm from the suction side of the pump.
Question: What does the buyer need to know about, which is not always discussed during the sale, if a submersible pump supplies heavily polluted water when pumping a well for the first time?
Answer: When the pump pumps heavily polluted water, it is forbidden to turn it off, otherwise its impellers can simply jam due to sand settling from the pressure pipe. He should be allowed to work. The pump can be turned off only after it goes out of the line pure water. In the process of pumping a well with a Vodomet pump, the pump pumps water with a high content of sand, sand can exceed the norm several times, which means that there is a high probability of wear of anti-friction washers. After pumping the well, I recommend to make Maintenance pump by contacting a specialized service center.
Question: What ensures a high throughput of impurities among domestic and even imported domestic submersible borehole pumps?
Answer: This is achieved by "floating" impellers and increased axial and radial clearances. It is due to this feature that the pump is able to pass through itself up to 2 kg of impurities per 1 m³ of water.
Question: How long can the water jet pump run continuously?
Answer: The pump can be operated in continuous mode, the pump is cooled by the flow of water pumped through itself.
Question: What is the maximum number of starts allowed per hour for the Vodomet pump?
Answer: The maximum number of inclusions is no more than 20 inclusions / hour.
Question: Is it possible to use the pump Vodomet 60/52 A in a well?
Answer:Submersible pumps A water jet with the index "A" is used only in wells, tanks or open water. It is not advisable to use it in a well, since the pump with the “A” index is equipped with a float electric valve to turn the pump on and off as water enters. A pump with a valve may simply not fit into the well.
Question: Where to locate and why you need a mechanical check valve on the pump?
Answer: The non-return valve is installed no more than 7 meters from the pump or directly on the pump. I recommend installing an additional check valve at the accumulator to reduce water hammer in the water supply system.
Question: What should be the minimum allowable distance of the intake part of the pump to the bottom of the well or well?
Answer: The distance must be at least 1 meter.
Question: What is the minimum volume of the accumulator to be installed autonomous system water supply using a water jet pump?
Answer: The volume of the accumulator must be at least 50 liters. But the accumulator can be selected and accurately using the formula. Provided that you know the maximum volume of water that you will consume (Amax liters / min.), As well as the power of the submersible pump, knowing these parameters, you can supply water, using the table, select the appropriate volume of the accumulator Vt. Or use the calculator -
Vt- this is the volume of the tank, liters;
A max– maximum volume of consumed water, liters/min.;
Pmin- the minimum pressure at which the pump starts;
P max- the maximum pressure at which the pump is switched off;
R pres- initial pressure in the tank;
TO- coefficient corresponding to P pump power.
The pressure values in the table are expressed in bar.
Question: Do I need a stabilizer for the Waterjet pump to work? How to choose the right stabilizer?
Answer: The stabilizer equalizes the voltage in the mains to the nominal value of 220-230V. A voltage stabilizer is selected based on the power of the submersible pump. The pump power is multiplied by the factor "3", the power of the required stabilizer is obtained.
For example: The power of the submersible pump "Vodomet" 60/92 is 1100W * coefficient "3" = 3300 watts.
You will need a voltage stabilizer with a power of 3500 watts.
Question: I want to increase the length of the pump cable, will it be necessary to increase its cross section, why?
Answer: By increasing the length of the cable, it is also necessary to increase its cross section, because when you increase the length of the cable, the voltage drop on the pump itself also increases.
Selection table for electric cable section
| open wiring | Cable section, mm2 | closed wiring | ||||||||||
| Copper | Aluminum | Copper | Aluminum | |||||||||
| Current, A | power, kWt | Current, A | power, kWt | Current, A | power, kWt | Current, A | power, kWt | |||||
| 220 in | 380 in | 220 in | 380 in | 220 in | 380 in | 220 in | 380 in | |||||
| 11 | 2,4 | — | — | — | — | 0,5 | — | — | — | — | — | — |
| 15 | 3,3 | — | — | — | — | 0,75 | — | — | — | — | — | — |
| 17 | 3,7 | 6,4 | — | — | — | 1,0 | 14 | 3,0 | 5,3 | — | — | — |
| 23 | 5,0 | 8,7 | — | — | — | 1,5 | 15 | 3,3 | 5,7 | — | — | — |
| 26 | 5,7 | 9,8 | 21 | 4,6 | 7,9 | 2,0 | 19 | 4,1 | 7,2 | 14 | 3,0 | 5,3 |
| 30 | 6,6 | 11 | 24 | 5,2 | 9,1 | 2,5 | 21 | 4,6 | 7,9 | 16 | 3,5 | 6,0 |
| 41 | 9,0 | 15 | 32 | 7,0 | 12 | 4,0 | 27 | 5,9 | 10 | 21 | 4,6 | 7,9 |
| 50 | 11 | 19 | 39 | 8,5 | 14 | 6,0 | 34 | 7,4 | 12 | 26 | 5,7 | 9,8 |
| 80 | 17 | 30 | 60 | 13 | 22 | 10 | 50 | 11 | 19 | 38 | 8,3 | 14 |
| 100 | 22 | 38 | 75 | 16 | 28 | 16 | 80 | 17 | 30 | 55 | 12 | 20 |
| 140 | 30 | 53 | 105 | 23 | 39 | 25 | 100 | 22 | 38 | 65 | 14 | 24 |
| 170 | 37 | 64 | 130 | 28 | 49 | 35 | 135 | 29 | 51 | 75 | 16 | 28 |
Question: How are centrifugal, vibrating and vortex pumps different?
Answer:
- Centrifugal pumps has a long service life, high throughput on impurities (sand) and high efficiency.
- vibration pump reduces the life of the water supply source (well, well), it breaks aquifers, well walls, wells, has elevated level noise, short lifespan, and poor performance.
- vortex pump combines the properties of centrifugal and volumetric machines, so the vortex pump provides high efficiency. Nevertheless, this type of pumps is characterized by a change in efficiency over time, because the hydraulic part of the pump has small axial and radial clearances. After the ingress of impurities (sand), the wear of its working surface reduces the flow-pressure characteristic.
Question: I'm going to cut the pump's plug, will the warranty still be valid?
Answer: If it is necessary to cut the electrical cable, for example, it is necessary to pass the electrical cable through the head or simply lengthen it, in this case the warranty remains valid. Be sure to use a heat shrink sleeve to connect the electrical cable.
Wiring diagram for a submersible multistage centrifugal pump Vodomet
Do you have a water pump? Everything suits me? Write in the comments about the experience of using this pump.
It is not enough to dig a well or a well. You should take care of how to supply water to the house, garden and other places. The water pump is designed for this purpose. The pump manufacturer is Dzhileks, a domestic leader in the manufacture of water pumps and related equipment.
Where can I use Gilex Water Cannon:
open waters,
wells,
wells,
various water tanks.
From the sources, water is supplied to the automatic water supply systems of the house, for watering the garden and garden, or for other purposes at the discretion.
Due to the layout features, the Gileks Vodomet pump can be placed at a depth of 100-150 mm from the water surface, and can also be used in a horizontal position. It is perfect for working in open and shallow sources.
How does a water pump work?
All Gilex models have a similar device principle. The stainless housing houses the pump part and the electric motor, which is washed by water. The rest of the parts are fixed with an intermediate support. The case is closed with covers on both sides.
The pump motor is filled with oil. The thermal relay is located outside the oil-filled cavity, which simplifies the repair of the part.
Depending on the model, the Waterjet pump may have different number repetitive steps. The parts of the device are divided into four components:
Cup.
The bottom of a glass.
Anti-friction washer.
Impeller.
The impellers rotate in the glass. And the cylinders are fixedly fixed between the cover and the plastic ring.
Device advantages
The manufacturer took care of human health. All parts of the Gileks water jet pump that come into contact with water are made of environmentally friendly and safe materials that do not affect water quality.
Some models of the Jilex Water Jet device have a removable filter. Its purpose is to protect the system from dirt, clay and sand. The filter extends the life of this equipment. If it gets dirty, you can clean it yourself. Also, the fence mesh has a large area. Water will fully flow even if the pump was lowered to the very bottom of the source.
The bottom cover has a conical shape. This design makes it easier to submerge the pump, it will not cling to possible casing connections.
The power cable can be pulled through the cover on top of the pump. Thanks to new design device it can be effectively used in wells with a small diameter casing pipe.
The engine of the Gileks water jet pump is cooled thanks to the duct cold water between stator and housing.
Automation, which is built into the pump system, excludes its operation in idle mode. This function protects the engine from overheating, which prolongs its service life.
The thermal relay built into the pump motor determines the oil heating temperature and, if the norm is exceeded, stops the operation of the device.
They are submersible devices. They are multi-stage units, the operation of which is carried out through the use of centrifugal force.
Among the characteristic design features, which differ borehole pump Water jet can be distinguished:
- powerful engine equipped efficient system cooling;
- "floating" impellers;
- connection of the power cable to the top cover of the product, so that it can be installed in wells with a small casing section;
- built-in capacitor that allows you to use a three-core cable for connection.
The isolation of the hydraulic and electrical parts from the immersion medium is carried out by mechanical seals, which increase the life of the unit.
Oil-filled engine driving deep pumps for the well Vodomet, differs in stability of working parameters.
It is equipped with a protective casing that prevents oil from penetrating the cable.
Depending on the modification, downhole pumps Vodomet can be equipped with:
- automatic equipment that prevents the possibility of idling and protects against deformations.
- a removable filter, which is installed in the intake part and does not allow sand and dirt to be sucked in.
Operational Benefits
The borehole pump Dzhileks Vodomet differs in reliability, simplicity in use and service. Its other benefits include:- High efficiency, providing good performance and other technical parameters.
- The presence of protection in the form of a thermal protector, which protects the engine from overheating.
- Long service life. The pump for the well Water Jet Dzhileks can be used for a long time in intensive mode due to the special arrangement of parts and the use of high-quality raw materials.
- small size and weight, simplifying the transportation of the device. In addition, they help to reduce vibrations.
Pumps for water wells Vodomet are characterized by economical energy consumption and almost no noise during operation.
Cooling the motor with pumped water ensures trouble-free performance of the specified functions.
The relay, which protects against overheating, is placed outside the stator windings of the power mechanism. This makes it easier to diagnose breakdowns and carry out repairs.
Thanks to the use of "floating" impellers, Vodomet well pumps are not very sensitive to the composition of the pumped liquid and can be used to transport water with a high sand content.
Degree of protection IPX8 protects against ingress of moisture and is designed for operation in immersed state for more than 30 minutes.
Suggested range
Pumps for the well Vodomet are represented by several models. They differ in the nuances of design, technical characteristics and equipment.The line of equipment includes devices that can be used:
- for watering;
- for sources with low debit;
- for the organization of automatic supply.
Downhole pump Dzhileks Vodomet PROF - a classic downhole pump, with which it is very easy to organize a water supply system. It will need to purchase a hydraulic accumulator, a pressure switch and other components.
Borehole (well) pump Gilex Water Jet PROF A equipped with a float switch, which prevents operation without water. It turns off and on automatically.
well pump Water cannon "House" represents a more advanced version of the equipment, in terms of technical equipment.
It refers to automatic systems water supply and includes the following elements:
- well pump Water jet with a wire for connecting to the electrical network;
- storage tank with a robust steel body and a flexible synthetic rubber membrane;
- three-pin fitting;
- stop valves;
- non-return valve that prevents fluid from flowing in the other direction.
Using the remote control with a microprocessor, you can program desired parameters in the pipeline, depending on the operating conditions.
The Dom model is a modified water jet pump PROF, which has retained all the best properties of basic products and is equipped with several additional functions. Among them:
- protection against "dry running", voltage surges and overloads;
- smooth start, which reduces the likelihood of water hammer during commissioning and reduces loads.
Application features
In order for the Vodomet downhole pump to retain its functionality for as long as possible, it is necessary to strictly follow the rules of use recommended by the manufacturer. According to them, you should:- apply for pumping medium, the temperature of which is from +1 °C to +35 °C and does not go beyond the specified limit;
- avoid installation in sources where the distance to the day is less than 1 m;
- exclude the pumping of liquid containing more than 2 kg / m 3 of sand in suspension;
- do not allow borehole pumps Vodomet to use if a violation of the integrity of the wire is detected.
If you are going to use the Dzhileks Vodomet borehole pump for its intended purpose, you must first check the performance. To do this, it is connected to the power supply for a few seconds.
When using the Vodomet pump for wells, it is necessary to provide for the installation of a head that will close the top of the casing and protect it from foreign objects and groundwater.
To prevent freezing, it will be necessary to build a well with a cover, and lay the pipeline below the soil freezing level characteristic of the area.
In this case, the internal cross section of the pressure water supply should not be less than the same parameter of the inlet of the apparatus for water supply.
To hang the water jet borehole pump, you will need a steel cable that is pulled through the lugs in the cover. It must support the weight of the apparatus and the filled pipe.
During the first start-up, the possibility of getting a significant amount of sand should be taken into account. In such a situation, it is forbidden to turn off the unit: it is left to work until the source is “pumped” and there are no impurities.
Mounting example
In order to ensure uninterrupted operation of water production, it is necessary to install special equipment. Pumps Dzhileks Vodomet for pumping water, you can install with your own hands near the mouth of a source of drinking or technical water.
In addition, Dzhileks Vodomet pumps for pumping water from a well can be immersed under the surface of the water table. This one is able to extract the required volumes of water from a do-it-yourself well and supply it to the house, outbuildings, greenhouses or gardens.
1 What is the design of Dzhileks Vodomet pumps?
The Gileks Water Jet pump for water extraction is presented in the form of a multi-stage unit, the principle of operation of which is based on the active use of centrifugal force. All Dzhileks Vodomet pumps for pumping water are equipped with floating wheels and a washed motor. A do-it-yourself unit can reliably supply water from:
- reservoir;
- open reservoir;
- Wells.
Due to the presence of floating wheels, the Dzhileks Vodomet pump for pumping water has enough high rates hydraulic efficiency. Reviews about such a pump, for the most part, are only positive.
Specifications devices Gileks Vodomet are quite high, this is also evidenced by user reviews. Thanks to a number of design improvements, the Dzhileks Vodomet pump has a fairly compact axial dimensions of the body and a low weight of all rotating working elements.
The consequence of all this is a significantly reduced level of vibration of the unit during its operation. In addition, it will not be difficult to disassemble such a pump with your own hands and repair it.
The use of floating wheels in the pump contributes to the minimum number of blockages that occur due to the ingress of large particles into the system.
In addition, the electric motor of the pump is well protected against sudden overheating. The characteristics of the device allow washing the engine with a stream of water in order to cool it.
In addition, the presented pump can be installed in the well with your own hands. Repair of this unit can also be done by hand.
Feedback on the installation of the pump with your own hands and how it was repaired will help you figure out how to properly carry out the procedure for such work.
The engine is located above the pumping part of the device. Such a feature constructive solution allows you to output the power cable directly from the .
Thanks to this, the pump can be mounted in a well with a minimum working diameter, and it can be easily repaired if necessary.
It should be noted that the presented layout of the pump has proven itself well in cases where the design is used and when it is partially submerged.
The unit itself consists of two main parts - this is the engine and the pump compartment, which is located in a common housing. All other moving parts and elements of the unit are centrally fixed in the housing using a special intermediate support.
It also uses the front and back covers. The pump is designed in such a way that the floating wheels included in it can approach each other.
Due to this, there is a significant reduction in the gap between the parts of the device that are in a movable state and the fixed parts.
This solution avoids the occurrence of internal leaks and, in general, has a positive effect on increasing the efficiency of the entire system.
All presented units, depending on the types of marking, have a different number of repeating steps. All parts in the device are divided into four subspecies. This:
- Impeller.
- Cup.
- The bottom of a glass.
- Anti-friction washer.
The glasses are made in the form of cylinders made using black polyamide. Each of them is equipped with a belt that rests against the ring.
The ring is inserted into the spacer located in the body. An anti-friction washer is located between the glass and the impeller; it is designed to prevent friction of the mechanism parts.
The whole system is based on the rotation of the impellers located in the glasses. The cylinders are fixed and do not move due to the fact that they are fixed between and the cover.
1.1 Types of models
All units are divided into three main categories. These can be pumps for extracting water from a well; a special cooling jacket is supplied with such devices.
In most cases, the systems are used in the arrangement of private houses or summer cottages. Downhole type units are used to provide water supply from those wells that have a large diameter.
In addition, such pumps are used in all kinds of tanks and reservoirs. Chastotnik type systems are widely used in areas where uninterrupted water supply is required in automatic mode.
As a rule, these are cottages and suburban areas. An important advantage of such a device is the ability to provide the desired level of pressure in the entire water supply line.
The pressure level is not affected by the number of points from which water is drawn. Feedback on pumps is mostly positive.
1.2 Specifications and reviews
Here are some specific parameters of the most common models.
Water jet pump "Prof 60/32"
In this series, the overall performance of the unit has been significantly improved. It is used to extract water with a large amount of sand diluted in it.
- Well depth: 30 m;
- Power: 470W;
- Pressure inside the system: 3.2 bar.
Water jet pump "Prof 60/32" A
The presented model is capable of pumping not only from wells, but also from wells, reservoirs and reservoirs. It is actively used for watering vegetable gardens and orchards. There are restrictions on the on-off cycles of the device - no more than 20 times per hour.
- Well depth: 25-30 m;
- Maximum pumped liquid temperature: +40 °C;
- Power: 500W;
- Pressure inside the system: 3.4 bar.
Water jet pump 60/62 A
A submersible type unit that can pump water from great depths. Carries out supply from deep wells, is used for irrigation and watering.
- : 52 m;
- Maximum pumped liquid temperature: +35 °C;
- Power: 630W;
- Pressure inside the system: 3.6 bar.
Vladimir, 43 years old, Ussuriysk:
I decided to equip my own yard and took up the water supply system. On the advice of a neighbor, a submersible pump Dzhileks Vodomet was installed in the well. While everything suits, water is supplied with great pressure.
Sergey, 50 years old, Voronezh:
I live in a private house, the forces are no longer the same as to constantly turn the handle of the well and carry full buckets of water. He equipped the well with a special well pump Vodomet. Now it is not at all difficult to get water, the pump pumps perfectly. I am satisfied with the purchase, I advise everyone!
Pavel, 37 years old, Saratov:
I have been installing water supply systems and related equipment for several years. All the clients to whom I installed Gileks Vodomet units were satisfied, there are no complaints.
1.3 What models of Vodomet pumps are there? (video)
2 The most common malfunctions and their repair
One of the most common unit malfunctions that require repairs is that when the device is turned on, the pump does not pump water.
If you listen carefully, you can sometimes hear a barely noticeable buzz. Sometimes the device does not make any sounds at all and can be shocked at the moment when the user touches its case.
All these signs indicate that there was a partial abrasion of the covers located between the stages and the impellers. In order for the unit to work again, it must be completely disassembled and worn out impellers and covers must be replaced.
In addition, another cause may be a faulty capacitor. In such cases, the incorrect operation of the device is due to the ingress of water through the cable passage into the cavity of the capacitor compartment.
A faulty capacitor is subjected to mandatory replacement. In the event that when the start button is pressed, the pump does not turn on, first of all, you should make sure that there is voltage in the electrical network.
First of all, the integrity of the cable, which provides power to the unit, is checked. It happens that the control panel of the device fails.
In this case, it is almost impossible to make repairs on your own. Here you will need the help of a qualified specialist.
You should also act if protection is often triggered, which is activated in the event of a breakdown of the power cable and leakage of electricity.
If, during start-up, the device turns on, but does not pump water, check that the valve is installed correctly.
In this case, the pump must be lifted out of the well and make sure that the valve is installed properly. Sometimes it happens that an air lock forms inside the unit.
To eliminate it, it is necessary to immerse the pump to a greater than usual depth. In this case, the valve is installed at a height exceeding 1 meter.
Another reason for such a problem may be improper installation and installation of a check type valve. In this case, the pump is also removed and the check valve is reinstalled.
If, when the system is turned on, a partial supply of water is produced and its pressure constantly weakens, then, most likely, the equipment was operated without turning off for quite a long time. The reason for the low pressure is a clogged cleaning filter.
If it is clogged, the filter is disassembled and cleaned. Otherwise, it is completely replaced.
During the intake of water, the pump in some cases gets a large number of sand. In such a situation, the unit is placed in a container with water and it is pumped.
In order to avoid such moments in the future, you need to take care of installing an additional cleaning filter. If the equipment has completely stopped pumping water, then first of all the unit should be de-energized and removed from the well in order to conduct a detailed inspection.
With such a breakdown, the cause may be a significant decrease in the water level in a well or well. It is necessary to immerse the pump to an even greater depth.
In some cases, equipment jamming occurs. Often this is observed with severe contamination of all channels. If it is not possible to eliminate the cause with your own hands, then you should contact a qualified specialist or a service center.
The pump "Vodomet" for a well is a multi-stage equipment with floating impellers washed by water. Water cooling is one of the important factors which prolongs the life of the device.
Description
The design includes a built-in condenser, which is necessary for supplying water from the well. His inner diameter may be 100 mm or more. It is noteworthy that such a device is suitable for working in wells that contain an increased amount of sand. These pumps can be used with control by the level of filling the tank or by the level of liquid pumped out of the system. automatic control by pressure. Not only a well, but also an open reservoir, as well as a well can act as a source of water supply.
Feedback on the choice of model
If you decide to purchase a Vodomet pump for a well, you should be aware of the criteria by which this equipment is selected. According to users, it is important to pay attention to the numerical designation, the first digit indicates the maximum one minute output in the absence of flow resistance. Looking at the second number, you can understand what is the maximum head in meters developed by the equipment when working "to a dead end".
If you have a pump of the Vodomet 60/52 brand in front of you, then, according to buyers, this indicates that with a free spout, the equipment is capable of supplying 60 liters of water per minute. This volume is equivalent to 3.6 cubic meters per hour, while when the supply is cut off, the pressure will be 52 meters, that is, 5.2 atmospheres. This unit is almost never used in the limit mode, most often it is operated at the operating point.
The pump "Vodomet" for a well with a maximum flow rate of 115 liters per minute is used for wells and wells with an increased and average flow rate. If there is a need to select equipment for water sources with a high flow rate, then you should purchase an option with a maximum flow rate of 150 liters.
General characteristics of submersible type devices
The submersible pump "Vodomet" for the well has a high coefficient useful action he is ready to serve long time. This equipment has a powerful electric motor cooling system. The design of the pump has a cable that can be pulled through the top cover, which allows the equipment to be used in wells of even the smallest diameter
It is noteworthy that these submersible pumps can operate continuously for a long time, this became possible due to the presence of a built-in water "jacket". It provides water passage between the motor stator and the housing. "Water cannon" is capable of supplying liquid from shallow or great depths. The devices have good tightness and are equipped with a thermal protector, which is responsible for the temperature of the equipment.
Characteristics of the pump brand "Vodomet prof 60/32"
If you are interested in the products of the brand "Vodomet", the pump for the well "Prof 60/32" can be purchased by you. It belongs to the high performance series. Such equipment is suitable for water with a significant sand content. It can only be used in those wells whose depth does not exceed 30 meters. The temperature of the liquid should not be more than 35 degrees.
Consumers who decide to purchase this equipment should be interested in the power of the submersible pump, which is 470 watts. In one minute, it will be able to produce 60 liters of liquid, the maximum amount of pumped sand will be equal to 2 kilograms per cubic meter of water. The products of the brand "Vodomet" have long become popular with Russian consumers, the pump for the well "Prof 60/32" is a confirmation of this. Its body is made of high quality stainless steel, which ensures a long service life of the device. However, in the process of using the unit, you must remember that the pressure should not be higher than 3.2 bar.
Characteristics of the pump brand "Prof 55/50"
When you visit the store, you can find large assortment goods that are manufactured under the brand "Vodomet". The 55/50 well pump can be considered as an example. The depth of its immersion is 30 meters, the power is 680 watts. The equipment must be installed vertically. As practice shows, the engine runs silently, and it is capable of pumping out 3.3 cubic meters per hour. This equipment should not be used for dirty water, because in this case it may fail. The size of the particles to be filtered can be up to 1.5 mm and the length of the power cord is equivalent to 20 meters. This information will help you when installing the device.
Characteristics of the pump brand "Dzhileks Vodomet 115/115"
If you are interested in the Vodomet brand, you can purchase a pump for a well 115/115 for 14,300 rubles. This submersible equipment is designed to pump water from a well, while the liquid may be slightly contaminated. The maximum depth, as in the above case, is 30 meters. Productivity is 6900 liters per hour. The advantage is that the device can also be used for small wells. With it, you can water the garden or garden, among other things, it is suitable for water supply in homes. The weight of the unit is 22.6 kilograms, which makes it easy to install.
This pump "Dzhileks" for a well, the photo of which is presented in the article, has a fairly wide area of use. It can be used in tanks, as well as open reservoirs. The equipment is perfectly adapted to difficult Russian conditions. To create it, the manufacturer uses durable and wear-resistant materials. For example, granite and ceramics are selected for. With regard to such important element, as impellers, a wear-resistant polymer is used for them.
Living and dead water: myth or reality, what is the power of living and dead water?
Craniosynostosis, or premature fusion of the bones of the skull Frontal crest in a child
Beautiful hair How to achieve hair density at home: useful tips
Why mosquitoes bite some people, but not others
How to achieve beautiful hair