Juicer screw press. Press for apples (wine press), purpose and features

03.03.2020

About 30 years ago, back in the USSR, the TV show “You Can Do It” was very popular, in which home-made people demonstrated their developments. I remember that I was somehow literally struck by an unusual press for extracting juice from apples using a car jack, developing a force of up to 5 tons. The originality of the design was that the juice from the apples that were in the tank was forced up and merged into a separate container. Over time, I made such a juice press and ... got disappointed in it, because from three buckets of crushed apples I got only 5 ... 6 liters of juice. Once, when trying to increase the compression force to 5 tons, the tank burst, and it was made of stainless steel 4 mm thick.

Later, experimenting with chopped vegetables and fruits, I came to the conclusion that in order to maximize the yield of juice from raw materials (up to 65 ... 70%) when using a press, it is necessary:

crush the feedstock into crumbs 2 ... 4 mm in size. And green grass should be passed through a meat grinder, and currant berries, chokeberry should be heated in the oven at a temperature of + 60 ° C for 20 ... 30 minutes;

spread the crushed raw materials in portions of 1 ... 2 kg (no more!);

wrap individual portions of raw materials in napkins made of durable fabric (lavsan, packing calico) measuring 50x50 cm;

into the press, stack the portions wrapped in napkins, using drainage pads made of stainless steel.

It turned out that under these conditions, the need for a jack disappeared, since for high-quality juice extraction, the efforts of the “screw-nut” pair, which I borrowed from the water valve (the screw is made of stainless steel 40X13), were enough. After all, work efficiency homemade press for squeezing juice, it was determined not the forces applied to the raw material, but a significant surface area of the squeezing mass, as well as the fact that the juice from the portion could come out “in all directions”, and not only from below or from the sides.

How to make a homemade juicer

The design of the screw press for juice is clear from fig. 1. Actually consists of two rack-pipes with a diameter of 22 mm. From above, a U-shaped profile bent from 3 mm steel is welded to the pipes. The height of the profile is chosen in such a way that the screw nut pressed into the steel bushing is freely placed inside. A clamp is welded to the bottom of each rack. With the help of these two clamps, the press is attached to the windowsill. A head with a hole for a handle is welded to the screw on one side, and on the other, a stop is attached, which compresses the raw material.

A leaky 3-liter enamel pan came up to collect the juice (Fig. 2, a). I drilled a hole in the bottom and fixed a fitting with a hose for collecting juice in it.

The basket (Fig. 2, b) was made of stainless steel sheet 2 mm thick, top and bottom, bandages-rings made of stainless wire 4 mm in diameter were welded to it. The rings allow the basket to "evenly" fit inside the pan. Yes, the walls of the pan are perforated with a 3 mm drill (in random order).

Gaskets (Fig. 2, c), which separate the portions of raw materials loaded into the basket, consist of two disks of 2 mm stainless steel, connected by spot welding. Holes were drilled in the disks with a drill with a diameter of 3 mm, gaskets 4 mm thick were provided between the disks (gaskets are also made of stainless steel). In general, I made all the details of the screw press from stainless steel, because at that time stainless steel was literally lying under my feet.

The work of squeezing the juice is as follows. The press body is fixed with clamps on the windowsill in the kitchen (you can also install the press on the table). The screw with the stop is unscrewed to the stop. A basket is placed in the pan, and a gasket is placed on the bottom of the latter and a napkin made of durable fabric is placed on it. Next, crushed raw materials (apples, fruits, herbs, berries) are placed on a napkin in an amount of 0.5 ... 1 kg. The napkin is folded into an envelope, the portion is covered with a drainage pad, on which the next napkin is placed. There should be 3 such packages, while the top package can rise above the pan by 4 ... 6 cm. Putting a gasket on the top package, the pan is installed under the press screw. Yes, I completely forgot to say about the spacer (a circle of wood), which is placed under the basket (otherwise the pan may become unusable when the screw is tightened). When creating pressure, the screw must be turned slowly and smoothly, watching the juice flow out. Having finished squeezing the juice, the screw is turned up, the pan is transferred to the table, the cake is removed from the napkins. Depending on the type and quality of raw materials, in one cycle, using a home-made screw press for squeezing juice, it is possible to squeeze 1.2 ... 1.8 liters of juice, and in 1 hour - up to 12 ... 15 liters.

The end of summer, the beginning of autumn is the time for picking fruits, vegetables, apples, grapes. And if the harvest is large, then an ordinary electric juicer will not cope. In this case, you need a press to squeeze juice from fruits to give. Now there are a lot of offers on the network for various presses and crushers, hydraulic, screw, pneumatic, wooden, but the biggest disadvantage of these products is the high price. Making a juice press with your own hands is not difficult, you need small skills of a locksmith, welder. And the cost of a home-made press for grapes or apples is several times lower than the purchased one.

For the winemaker, such a device will facilitate his work and save a lot of time. The simplest version of a home press-juicer is based on squeezing juice from the pulp of fruits or vegetables. Previously, apples are crushed with special crushers, a grape crusher is used, and then juice is squeezed out of this mass. With this technology, pure juice without pulp comes out, ready for fermentation, or for pasteurization and further storage.

A simple do-it-yourself grape press

A screw press for grapes consists of: a base - a frame, a basket, a pressure device (shaft or jack), a pressing piston. Other options for manufacturing the device are also possible. When choosing a material, it is not necessary to follow the description exactly, and you can make your own drawings of a Persian.

Tools and materials for the press:

Welding machine;
Drill;
Bulgarian;
Tank - 50 liters;
Metal channel 10-12 mm - 150 mm;
Metal corner 40-50 mm - 3200 mm;
Oak slats 40x25x400 mm - 50 pcs;
Fabric - 1 sq.m;
Jack - 1 pc;
Faucet - 1 piece;
Fishing line 2 mm - 3 m.

How to make a juice press

1. Frame. Foundation is one of the most important elements press, the frame must be a very strong structure, it bears all the load during operation. The side parts of the press are made of metal corners 85 mm high. The upper and lower parts of the frame must be made from a channel 70 cm long, you can further strengthen the structure by welding scarves between the corners and the channel. All parts are welded at all points of contact.
If a screw press design is used, then a nut for the screw must be welded to the upper channel. In addition to the metal frame, you can use wooden boards with a thickness of 5 centimeters or more. The boards are fastened with 10-12 mm studs and tightened with nuts. It is easier to make a wooden press, but the design does not withstand heavy loads; for a small crop, it is quite a suitable option. The finished frame must be sanded and painted with a special paint for metal.

2. Tank for the press. This design uses a stainless steel brew tank with a volume of 50 liters. A hole was drilled in the lower part of the boiler tank and a stainless steel tap was installed. Instead of a tank, you can use a regular pan right size.
A lattice of oak slats is inserted into the container. The blanks are cut from an oak board (you can use a parquet board), their height is equal to the height of the pan. Along the edges at the ends of the rails, holes of 2-3 mm are drilled through them, a fishing line or stainless wire is passed through them. By connecting all the planks, you get a kind of basket.
There should be a gap of 2-3 mm between the slats, through which fruit juice will ooze. You can do without a pan at all by connecting the boards with galvanized steel hoops and placing the basket on a pallet into which the squeezed liquid will drain.
As a pallet, a plastic pallet from a large flower pot or stainless steel kitchen sink. There is a design where the grape press is made frame, there is no basket in it, the cake is placed in the fabric between the drainage grates in several layers and choked.

3.Piston. The piston for the press must be made from the remaining oak boards, folding them crosswise, draw a circle using a compass right size and cut with an electric jigsaw. Twist the rails with stainless steel screws or tie with copper, stainless wire. If the farm has a log, then you can saw off a circle of the required diameter and height.

4. Power mechanism. A jack or screw is used as a pressure mechanism in an apple press. A hydraulic car jack with a lifting capacity of 3 tons will be quite enough in a juice extractor. For more confident work, you can use jacks that create a force equal to more than 3 tons. The screw for the press is more difficult to find, and every motorist has a jack. Under the jack, you need to cut planks for laying during the spin cycle.

5. Fabric for filtering. To filter the juice from apple fruits, you need a durable fabric that can pass moisture. The easiest option is to take a nylon sugar bag. Nylon, lavsan, propylene, polyester are also suitable for filtering, or use durable cotton material, dense linen, so as not to tear under pressure.

So, the manual fruit press is ready, how to squeeze the juice? Insert the basket into the tank, place the material to be filtered inside. Soft fruits, berries, citrus fruits are crushed without pre-treatment. Apples, carrots or other hard fruits must be crushed in a crusher or use pulp from a juicer, loaded into a basket, covered with a lid.

Install the jack, substitute the receiving container, open the tap and slowly press. Do not immediately try to squeeze out all the juice, you can damage the frame or the fabric will tear. Do three or four strokes, wait a while, then three or four more strokes, and so on. From one bucket of apple cake from a juicer, 3-4 liters of pure juice comes out, a little more from the crushed mass.

As a rule, a fruit press is designed to completely extract the juice from them after crushing. Apple presses are especially effective if the latter are thoroughly crushed. If juice is required for wine, then for white it is recommended to press immediately after the crushing process. For red varieties, this procedure is done after several days after fermentation. In this case, oxidation does not occur, and the aroma of the squeezed juices remains unchanged, and the product itself is suitable for consumption. For high-quality juice extraction, it is not recommended to squeeze large pieces of fruits and vegetables. A manual fruit press that will become indispensable assistant in the preparation of fruit cocktails and other dishes, you can buy through the website of the VTK-Prom Group of Companies. This device is widely used at home.

Juice press, advantages and principle of operation

The most common juice presses are screw presses. These are periodic exposure devices that include: a base with a fixed screw, which is considered the main working mechanism; the basket used for the pressed mass; pressing element, otherwise called "press head". At first glance, a simple design provides efficient work. Such juice presses allow you to squeeze the maximum out of fruit in the shortest possible time. The high efficiency of the mechanism is due to the screw technology used, which allows you to systematically increase the pressure on the squeezed mass. Juice presses that use this principle of operation in their work are made both with a steel body and with a wooden one. Device platforms are made of wood and concrete, cast iron and sheet steel. A screw press for juice is often used for the production of wine. In view of the fact that it has to be put into action with the help of the efforts of the hands, it received another name - a manual juice press.

Fruit press, advantages and principle of operation

To process a large mass, fruit presses are used with much higher productivity than juicers. The most cost-effective are those that do not consume electricity. Some call them a winemaker's dream. And yet, the press is not the main home device for squeezing the fruit mass; a juicer is often used along with it. The latter is based on cold press technology. Group of Companies "VTK-Prom" offers you to purchase all these products at the best price. High quality and durability are guaranteed as all the products shown are made in our own production facilities.

Special offer:

Juice Making Kit
The kit includes a traditional screw press (18 l) and an apple chopper with a handle (7 l) for making juices from fruits and berries or for making cider.

Press juicer with filter
A screw press with a robust design greatly simplifies the production of juice in small farms. Easy to use and maintain, can be taken to the country/village.
Basket volume: 18 liters, basket size: Ø 360 x 600 mm

Mechanical Fruit Crusher
A crusher is needed to crush apples before pressing. The mechanical crusher-chopper has acid-resistant steel powerful teeth that capture apples and pass them through the dryer. Vyaltsy and teeth are set in motion by rotation of the handle fixed on the side. Hard apples are recommended to be divided in half before chopping. To simplify the process of making juice, the crusher can be placed on a press basket or on a free-standing vessel.
Properties:
» Grinding capacity: up to 300kg/h
» Tank volume: 7l
» Material: stainless steel tank and painted construction
» Weight: 12 kg
» Dimensions: 310x335x235 mm

Price per set: 23 200 rubles

FP series apple presses (grape press)

The FP series is represented by one small press with a volume of 6 liters. Screw press FP - 6 is indispensable for squeezing juice from prepared: tomatoes, grapes and other berries; used in the manufacture of homemade cheese, in beekeeping; squeezing excess oil or juice after conservation and other cases when it is necessary to extract liquid from the product.

TOTEM FP-6 - Price 9400 rubles.

Apple presses TOTEM series AP (Apple Press) (Garden juicer)

The mechanism of screw presses-juicers is put into operation by rotating a handle fixed on a large nut that goes down the screw. Load the crushed mass into the juicer basket and place pressure semicircular plates and pads on top.

The AP apple press series is represented by the following models:

TOTEM AP-6 (with basket volume 6 liters) -- Price 8300 rub.

TOTEM AP-12 (with a basket volume of 12 liters) -- Price 11,000 rubles.

TOTEM AP-18 (with basket volume 18 liters) -- Price 14,000 rubles.

TOTEM AP-30 (with a basket volume of 30 liters) -- Price 21 000 rub

Apple Presses TOTEM APR Series (Manual Juice Press)

The mechanism of the screw press-juicers of the APR series is similar to the mechanism of the presses of the AP series, except that it is driven by turning the handle not in a circle, but in an arc, due to the fact that the large nut that goes down the screw is equipped with a ratchet. Load the crushed mass into the basket and place pressing semicircular plates and pads on top.

The basket of the press is made of beech, the parts of the basket are interconnected by a metal rim and fixed with bolts. The basket stands on a metal tray into which the squeezed juice flows. The metal parts are covered with enamel.

The legs are provided with holes through which the press can be screwed to the base with screws.

The APR series of orchard apple presses is represented by the following models:

Apple presses TOTEM series APF - (Manual fruit press)

Frame press juicers are designed for people who value convenience and comfort in work. The folding frame allows you to quickly and easily fill the basket with crushed apple mass. By returning the frame to its original position, you can immediately start pressing.

The APF series press basket is made of beech, the tray is made of enamelled steel. Crushed fruit should be placed in the press.

From the outside, the parts of the basket fit snugly against each other, from the inside they form grooves, through which the juice flows down to the tray, and from the tray into a container placed under the spout.

The APF apple press series is represented by the following models:

Large-size apple presses TOTEM series APF (Apple Press Frame type)

The design of the large size apple presses is similar to that of the APF series apple presses, except that these presses are equipped with special mechanism for lifting and turning the basket and a more powerful screw.

The APF series press basket is made of beech wood. Plus, the juice collection tray is made of stainless steel.

Crushed fruit should be placed in the press.

The APF series of large-sized apple presses is represented by the following models:

TOTEM APF-36 (with basket volume 36 l.) -- on order

TOTEM APF-72 (with basket volume 72 l.) -- on order

APS Series Apple Presses (Manual Apple Press)

The APF series press basket and tray are made of stainless steel. Crushed fruit should be placed in the press.

The basket can be easily removed and it is convenient to take out the cake from it.

The basket is made of perforated metal with holes through which the juice flows down onto the tray, and from the tray into a container placed under the spout.

The APS apple press series is represented by the following models:

TOTEM APS-14 (with basket volume 14 liters) --18 500 rub.

Hydraulic fruit press

Hydropress for an extraction of juice on 28 l. Great for both personal plot as well as for small production. The hydraulic press will save you time. All you need is to connect to the water supply. ( required pressure 3 atm).

The price of the hydraulic press GP-28 is 31,000 rubles

Please note that appearance products may differ slightly from the images in the photographs.

An apple press allows you to make juice from fruits or make apple wine with your own hands by pressing. The basis of apple drinks is precisely a portion of juice, therefore your main task is to squeeze out the most delicious liquid from the fruits of apples.

All presses designed for squeezing apples and other fruits in order to obtain juice can be divided into several types:

Manual (mechanical). The main work is done through physical effort. At the same time, mechanical-type wringers are the easiest to assemble;
Hydraulic. The hydraulic juicer operates on the basis of a hydraulic pump that creates pressure for squeezing juice from fruits and apples;
Pneumatic. The principle of operation is similar to hydraulic devices, but air is used instead of water. It is pumped with a compressor, carrying out the processes of squeezing fruits;
Electrohydraulic. The most effective types of fruit pressing devices. The work of such apple presses is based on hydraulics and electrics. With your own hands, you only need to load the raw materials.

According to the scope of application, all apple pressing devices are divided into two categories.

Household. It can be a simple screw unit, where the process of squeezing fruit is carried out due to physical effort. Also, a household juicer can have a hydraulic and electric drive. The Bogatyr juicer is in great demand among those involved in the manufacture of apple juice at home. The Bogatyr juicer costs about 5-8 thousand rubles. At the same time, you can make a full-fledged analogue of household factory presses with your own hands.
Industrial. The usual screw design of the press is indispensable in the conditions of large-scale processing of apple juice. This will require a conveyor belt. Belt press feeds a large number of fruit for further juice production. The belt conveyor has increased productivity, which is tens or even hundreds of times higher than the performance of self-assembled household presses.

Product preparation

To obtain high-quality apple juice, competent preparation of the fruits themselves plays an important role. You need to do everything right so that your Bogatyr juicer or its homemade counterpart performs the processing efficiently and efficiently.

The essence of preparing apples for juice production is to follow a few simple recommendations.

Prepare a container that will serve as a container for storing apples before sending them to the press. This is where you will place apples that are already directly ready for juice production.
Provide your work area with plenty of clean water. The optimal solution is a hose with reasonably good water pressure. If processing is done at home, apples can be poured into the bathroom.
Wash the apples thoroughly, removing all branches, leaves and ponytails.
Depending on the equipment used and the characteristics of the juice recipe, you will need to peel and cut apples.
Obtaining pure high-quality juice implies the need to cut apples into 2-4 parts, removing the core from them.
In some cases, it is recommended to take a sharp spatula and crush the chopped prepared apples in a container. This will make small pieces of pulp from apples. So they will stand out even more juice. But the use of some presses does not require these measures. Apples can be loaded into the Bogatyr juicer simply chopped and peeled.

Production of a press juicer

Making a press with your own hands, when you have photos, drawings and video instructions in front of you, is not difficult. A simple but effective juicer allows you to make a large amount of apple juice, using raw materials as efficiently as possible.

Yes, a factory juicer can outperform a homemade press. But not everyone wants to pay about 10-20 thousand for equipment. Buying a factory juicer is relevant when you plan to process a large number of apples. That is, the cost of acquiring the device will pay for itself over time.

For domestic use, you can make an excellent homemade juicer. We offer you instructions for making a structure that allows you to make high-quality juice from apples.

The presented homemade juicer consists of several main elements:

Frame;
Pallet;
Barrel;
Piston;
Power point;
filter cloth.

We will tell about each of the components of the juicer separately.

The frame and base are made of metal profiles by welding. When making the upper horizontal part of the frame, use a strong profile that will cope with the estimated loads. Lay a plywood sheet on the base. A pallet with a keg will be placed on it. Provide protection against corrosion and decay by covering the metal with paint and the plywood with a varnish composition.
You can use a ready-made plastic pallet. Pallets from flower pots. Finding a component of the required size is not difficult. Make a hole in the side of the tray by inserting a tube for the juice to flow out. But plastic pallets can break. An alternative solution is stainless steel pallets.
The material for the manufacture of the barrel can be a perforated tape made of galvanized metal or non-glued timber. If you use a beam, leave a gap between the strips no more than 5 mm. Wood is recommended to use from species of beech, birch or oak. But pine and other resinous trees should not be used for these purposes because of their biological activity. Resin can impart off-flavours and bitterness to the juice.
Piston. From wooden planks make a square. In this case, two layers of boards are needed, located perpendicular to each other. Having obtained a square, cut a circle out of it using electric jigsaw. Round the edges gently with sandpaper or a file. So he will not get stuck in the barrel. When making a piston from boards, be sure to use oak, birch or beech. Biologically active resinous tree species are out of place here. A metal pancake can act as a substitute for a piston circle from boards.
Power point. The optimal solution for self-manufacturing apple press will be a hydraulic jack. Its capacity of 2 tons is enough to cope with the production of apple juice. Hydraulic jacks have a small piston stroke, so you will need to make additional boards to be placed under the jack. Use a galvanized stud for the screw. A handle is welded to the stud, and a nut to the frame. It will rotate the screw.
filter cloth. To get juice and not applesauce, you will need to separate the liquid from the pulp. Simple and effective solution there will be a fabric that carries out the process of filtering the juice. A high-quality and durable fabric with a mesh structure is suitable as a filter material. Vivid examples are polyester or lavsan.

Apple juice is a favorite product of many. It can be obtained from apples growing in your garden. Assembling a homemade press is not difficult. If you need a lot of apple juice, buy an efficient and reliable factory press juicer.

Today we will talk about how to independently make a press for squeezing juice from fruits, berries and vegetables or a homemade juicer with your own hands. We will also consider the technologies and drawings of home-made presses and juicers with illustrative illustrations.

Exist various designs juice presses. Main homemade designs- these are screw or using a jack. A good option when using a pneumatic jack or a rubber chamber and a compressor. There are options for using a centrifuge, for example, an old washing machine. The press or juicers should not crush the seeds and ridges that are in the pulp.

Depending on the expected volumes of processing of raw materials for juice or wine, choose the design of the device for squeezing juice that you like. The cooking process in any case is divided into two stages: 1. Preparation of pulp (grinding raw materials); 2. Actually the extraction itself is getting juice.

Screw structures of the press for squeezing juice

Usually the press consists of a pressing mechanism, a basket, a base and a pressing board. The basket serves as a pulp receiver and is installed on the base of the press. There is also a tray for flowing juice. The bottom and side walls of the basket are lined with a whole piece of burlap without gaps. The ends of the fabric should hang over the edges of the basket. Then the pulp is loaded into the basket and covered with the ends of the burlap. A wooden circle is placed on top, on which the head of the press is lowered.

Here is an example of another homemade juice press. The press consists of two rack-pipes with a diameter of 22 mm. From above, a U-shaped profile bent from 3 mm steel is welded to the pipes. The height of the profile is chosen in such a way that the screw nut pressed into the steel bushing is freely placed inside. A clamp is welded to the bottom of each rack. With the help of these two clamps, the press is attached to the windowsill. A head with a hole for a handle is welded to the screw on one side, and on the other, a stop is attached, which compresses the raw material.

To collect the squeezed juice, a leaky 3-4 liter enamel pan is suitable (Fig. a). It is necessary to drill a hole in the bottom and fix a fitting with a hose in it to collect the juice.
The basket is made of stainless steel sheet with a thickness of 2 mm, bandages-rings of stainless wire with a diameter of 4 mm are welded to it from above and below. The rings allow the basket to "evenly" fit inside the pan. The walls of the pan are perforated with a drill with a diameter of 3 mm (in random order).

The spacers, which separate the portions of the raw material loaded into the basket, consist of two discs of 2 mm stainless steel, connected by spot welding. Holes were drilled in the disks with a drill with a diameter of 3 mm, gaskets 4 mm thick were provided between the disks (gaskets are also made of stainless steel). In general, all parts of the screw press are made of stainless steel; a tank from an old washing machine is quite suitable.

The napkin is folded into an envelope, the portion is covered with a drainage pad, on which the next napkin is placed. There should be 3 such packages, while the top package can rise above the pan by 4 ... 6 cm. Putting a gasket on the top package, the pan is installed under the press screw. Yes, I completely forgot to say about the spacer (a circle of wood), which is placed under the basket (otherwise the pan may become unusable when the screw is tightened).

When creating pressure, the screw must be turned slowly and smoothly, watching the juice flow out. Having finished squeezing the juice, the screw is turned up, the pan is transferred to the table, the cake is removed from the napkins. Depending on the type and quality of raw materials, in one cycle, using a home-made screw press for squeezing juice, it is possible to squeeze 1.2 ... 1.8 liters of juice, and in 1 hour - up to 12 ... 15 liters.

wedge fruit juice press

It is necessary to arrange wooden goats on four legs B 1 m high. At the top, these legs are connected by a thick (9-10 cm) board A, the width of which is 30 cm and a length of about 1 m. In the board we make a longitudinal slot D 10-12 cm wide and 40 cm. In this slot we insert two boards B (thickness 9-10 cm), hewn from above and below. In the lower part, we connect both boards with an iron bracket b or, even simpler, with a thick rope.

In order for the boards to hold and not fall into the slot, we skip iron pins or wooden bushings in their upper part. Then we make several wedges of different thicknesses from hardwoods - and the press is ready. It works like this: having parted boards B, we insert a bag of strong canvas filled with pulp between them. Then, driving wedges into the slot, we squeeze the boards. Thus, the pulp is strongly compressed. The juice flows down into the substituted tub or pot.

Making a simple lever juicer

We take two birch boards, the length of the main board is 1 m, the width is 300 mm, the thickness is 100 mm. The second board, which serves as a lever, is 1.5 m long, 170 mm wide and 20 mm thick. In the main board we make grooves for draining the juice (Fig. a) 10-15 mm deep and 300 mm long. We strengthen this board obliquely either on separate racks or on a special table. To it, with the help of a hinge and a gasket board, we attach a second lever board. Got a lever press. We put 4-5 apples or some other fruits in the opening, press the lever, and the juice flows down the grooves into the substituted container.

Nowadays, more and more often, self-taught masters are asking the question: “How to make a grape press with your own hands?” Grow grapes on your own garden plot simpler, simple, the berry is unpretentious in care, it grows quickly. Having built a press for him, it would be possible to harvest juice for the winter or cook your own Home wine.

A press with a basket of twenty liters is quite suitable for reaping juice from overripe grapes for wine.

Option one.

What is the press made of?

We will press screw type and it will consist of:

Screw. It's good if he rectangular shape, powerful and have a thread.

Basket. By the way, it can be made from parquet boards. Which then needs to be pulled together with stainless hoops.
.
Advice:

And if suddenly your local market does not suddenly have a strip of stainless metal of the thickness you need, in this case, grab the corners on the way home. After all, they can also fasten parquet boards.

The design of our press will be, so to speak, self-sufficient. That is, the finished press will be without stands, on legs. A nut will be attached from above, and the screw rod will be screwed into it. There will be a basket in the frame itself, the must with pulp or grapes will be loaded into it

We make a basket.

We buy a couple of dozen parquet boards: length - 320 cm, width - 50 cm and a thickness of 1.5 cm. We buy a metal strip, 1 mm thick. Many people buy metal corners from stainless steel. In this case, they will need a couple of pieces of two meters each.
We remove the grooves from the boards with a cutter. Well, this operation can even be called useless if you have Dishwasher. Since in this case, with the help of her brush, everything is perfectly washed. But if there is no car, so that the grooves do not get dirty, it is better to cut them off.
Now you need stainless steel screws. We attach them to the corners, the gap is no more than 12 mm. Then, with the help of a grinder, we cut a corner between the boards. We bend the edges. We make holes for the bolts in them.

You will need an insert, its diameter corresponds to the diameter of the basket. The piston is placed on the grape pulp.

The height of the basket is 32 cm. The diameter inside is 29 cm. The estimated volume is 21 liters exactly.

So, we continue the topic of how to make a grape press.

Now you need to buy:

Corners in 25 mm;

Drills, 6.2 mm in diameter;

Several M6 bolts;

Nuts to bolts.

We assemble the frame of the press.

Please note that it is necessary (!!!) to place boards under the screw, on top of the circle.

The screw can be ordered from a turner, or you can build it yourself if you have the appropriate skills.

Screw parameters: diameter - 30 mm, pitch - 3 mm, nut, disk with holes for fastening, welded.

More details:

A small piece of plywood, as a stand for the press;

Plastic bowl. We make a hole in it, put a tube in the hole.

Of course, everything can be done with a welding machine, but if there is none, and if there is no experience with this device, then the question immediately arises of how to make a grape press without welding. This is where the idea came to mind, to make a press on the bolts.

You can safely cook the parts with an inventory, right in your apartment on the balcony.

Design flaw.

Option two.

Step one.

In order to harvest grape juice right at home, to make jelly, juice, wine and other things, you will need a press. How to make a press for grapes, we will now tell.

You need a roller crusher. You can also make it yourself, for example, from a loading bucket. The berry will fall into this crusher. It is better to build it from wooden frame. We add a couple of rollers to the frame, also made of wood, a handle for rotation. We fix all elements with bearings.

Step two.

We prepare all the details. We make a frame from bars: length - 70 cm, section - 4 by 10 cm. Frame width - look at the length of the rollers, since the width depends entirely on how long your rollers will be. The optimal size can be called 20 cm. When constructing the structure, make sure that the distance between the bars is the same.

Step three.

For the press, the rolls must be made corrugated, 3 cm deep. The corrugation can be made helical, in this case, we direct the shift to the side by a couple of cm. Next, we fasten the rolls to the frame with bearings. They will spin on different axes and at different speeds.

Step four.

With the same diameter of the wool, it is necessary to make the diameter of the rolls different. What does it give? The speed of movement in a circle will be different. For such a press, a wooden bucket is needed, where grapes will be loaded. Choose a pyramid shape.

Step five.

We put the bucket on the frame rails. Our slats must be transverse. The distance between the bucket and the roller is minimal, better, no more than a centimeter. Ready. It's time to secure the handle for rotation. With its help, the grinding of raw materials and the pressure of the juice will be carried out.

Step six.

At the bottom of the structure we put a vessel for collecting juice.

We load the berries into a ladle, from there they pour onto the rolls. We rotate the handle, the berries are crushed and crushed until a puree is obtained.

Step seven.

We remove the berries from the bunch. Rinse well under running water. And only then upload it to the press. And when the juice is ready, wash the press with water and dry it with a soft towel or napkin. If it is not properly cared for, the wood will simply begin to rot.