Connecting the dishwasher to the water supply and sewerage: we use the connection diagram for work. Dishwasher Installation Choosing Detergents

Type of work	Unit.	Cost, rub
Installing a BEKO dishwasher (without electrics)		From 1400 rub.
Dismantling the BEKO dishwasher (without electrics)		From 700 rub.
Bosh dishwasher installation (without electrics)		From 1400 rub.
Dismantling the Bosch dishwasher (without electrics)		From 700 rub.
Installing a Samsung dishwasher (without electrics)		From 1400 rub.
Dismantling the Samsung dishwasher (without electrics)		From 700 rub.
Installing a Siemens dishwasher (without electrics)		From 1300 rub.
Dismantling the Siemens dishwasher (without electrics)		From 650 rub.
Ariston dishwasher installation (without electrics)		From 1300 rub.
Dismantling the Ariston dishwasher (without electrics)		From 650 rub.
Installing an Electrolux dishwasher (without electrics)		From 1100 rub.
Dismantling the Electrolux dishwasher (without electrics)		From 550 rub.
Installing a Gorenje dishwasher (without electrics)		From 1100 rub.
Dismantling the Gorenje dishwasher (without electrics)		From 550 rub.
Installing a Hansa dishwasher (without electrics)		From 1100 rub.
Dismantling the Hansa dishwasher (without electrics)		From 550 rub.
Built-in dishwasher installation (without electrics)		From 1600 rub.
Dismantling the built-in dishwasher (without electrics)		From 800 rub.
Installing a narrow dishwasher (without electrics)		From 1600 rub.
Dismantling a narrow dishwasher (without electrics)		From 800 rub.
Removing a dishwasher from other brands		From 550 rub.
Sealing dishwasher joints		From 450 rub.
Dishwasher drain connection (sealed)		From 650 rub.
Stroba on brick/concrete
Strobe for plaster and gypsum
Drilling holes for pipes
Wiring of sewer pipes (depending on diameter)		From 750 rub.

In 2007, the British company Hotpoint merged with the Italian Ariston. As a result, there appeared trademark Hotpoint-Ariston, which quickly gained a reputation for reliable home appliances.

Today, Ariston dishwashers are distinguished by high European quality and innovations that competitors do not have. In terms of sales, this brand ranks third among manufacturers of household appliances. The range of Ariston dishwashers is surprisingly extensive, and San Remo is ready to help with the installation of any model.

Ariston dishwasher installation cost

The prices for the Ariston dishwasher installation service vary, depending on individual characteristics and complexity of installation. We do everything preparatory work and install household appliances. The approximate cost of installation work is from 1000 rubles. For more information, please contact our phone managers listed below.

Features of installing Ariston dishwashers

With us you can call the master at home at any address. The specialist will arrive in a short time, inspect the place of the proposed placement of the household appliance and give his recommendations on the choice of equipment (if you have not bought it yet).

When connecting Ariston dishwashers, we pay special attention to the tightness of all connections so that even after a long time there are no leaks that can ruin your kitchen or flood your neighbors. Accuracy, reliability and quality assurance - that's what we offer to anyone who decides to order the installation of a dishwasher in San Remo.

We have prepared good discounts for our customers:

• 5% when ordering services for up to 15,000 rubles.
• 8% when ordering works with a total value of 15,000 to 20,000 rubles.
• 10% for those who order plumbing work from us in the amount of more than 20,000 rubles.
• 10% for all pensioners, disabled people, Veterans of the Great Patriotic War or Labor.
• 5% when ordering services online through the site form.

For most people, the attitude towards dishwashers is still quite wary - is it worth buying expensive equipment, if washing the dishes, in principle, is easy and by hand. However, if we recall the very recent past, then about the same thing was said about automatic “washers”, about food processors, even about TVs at the dawn of remote controls. remote control, and now without it it is difficult to imagine a normal life. You get used to good and convenient quickly, so many owners who have already installed a dishwasher in their kitchen will never want to lose such a “convenience”.

Others are following suit, and dishwashers are increasingly becoming an attribute modern kitchen. However, this is not at all the kind of household appliances that you can simply unpack, plug into a power outlet and immediately start using it. In addition to the rather complex electromechanical “stuffing” and automation, such an apparatus, to a certain extent, of course, is also a plumbing fixture. Therefore, it is extremely important to correctly connect the dishwasher to the water supply and sewerage. "Independent activity" in this matter is not welcome - you will have to comply whole line certain requirements. Let's try to understand this in more detail.

It must be assumed that if the owners nevertheless decided to buy a dishwasher, then they have already thought out the place of its installation in advance. AT in general terms it depends on which model is more to your taste - a compact desktop or built-in kitchen furniture. Accordingly, there may be serious differences in the installation and connection of the device to communications.

In both cases, the installation site of the machine is tried to be as close as possible to the area of ​​​​the kitchen sink. This is explained simply - it becomes possible to connect the device to utilities without resorting to a complicated procedure for inserting into pipes - it will be quite enough for those connections and assemblies that provide water supply to the mixer and drain it from the sink into the sewer. Lengthening the regular hoses of the dishwasher, especially the drain hose, is not welcome, since the capabilities of the pumping pump are limited, and you should not overload it, so as not to cause rapid wear.

However, such placement is not at all a dogma - you can also place the dishwasher in a more convenient place, from the point of view of the owners, but in such a way that, within the radius of the length of the regular hoses, there is the possibility of tapping into the corresponding sewers (this example will also be considered in the publication ), or you will have to think over the laying of an additional section of such pipes specifically for the purpose of connecting the device.

Of course, a power supply line of the appropriate section must be connected to the future installation site of the dishwasher, and a separate outlet must be installed, always with a ground loop. The use of extension cords should be completely excluded. Water, high humidity and electricity - already quite a dangerous "neighborhood", so no connivance like: "Petya's connected like that - and it's okay" - absolutely unacceptable.

The electrical supply of the kitchen is a matter of great importance!

Distinctive features of any kitchen are not only high level humidity and constant use of water, but also, perhaps, the largest power consumption of electrical appliances installed in it. Refrigerator, microwave, washing machine, dishwasher, extractor hood, electric stove and an oven, and that's not counting the lighting and small appliances! How to properly organize the power supply of the kitchen is described in detail in the article on our portal dedicated to.

The place for installation must be prepared - there is an appropriate niche for tie-in the right sizes or free countertop space for desktop installation. The base must provide a reliable position of the device, in a strictly horizontal position, supported by all the racks in order to avoid play or excessive vibration. Each model of dishwasher has its own requirements for site preparation, the technical documentation describes the installation, the kit usually includes all the necessary fasteners.

There is one more nuance of preparing for the installation of the machine - it must be taken into account in advance. Many models on the back of the case have power cable and hose outlets offset to one side. Thus, the permissible distance to the connection points may be different to the left and right of the dishwasher. Usually this feature is also indicated by the manufacturer in the technical documentation.

Before undertaking an independent installation of a dishwasher, the owner must carefully assess his capabilities and skills. If there are any doubts about one's own abilities, it is better to invite an experienced master plumber who has positive recommendations (a considerable number of frank "shabashniks" work in this field). The fact is that a violation of the installation rules may well lead to the termination of the warranty obligations manufacturer. Often, in large salons-shops, branded installation is practiced, for a low price, and sometimes even completely free - as one of the ways to stimulate consumer activity. This question should be immediately clarified when buying.

In the event that such a service is not provided, and the call of the master is seen as essential extra costs, then nothing is impossible and self installation. And if you “bracket” the already mentioned power line and the features of installing the device in a niche, then the main stage of the process is the correct connection of the dishwasher to the water supply and sewerage.

The sequence of steps, and is there always a need for a fixed connection

These steps can be carried out in any order. By by and large, more difficulties will be caused by preparation for connection - installation of all the elements necessary for this. And, in fact, switching the hoses coming out of the dishwasher with water supply and sewerage will be the final step, which is performed almost simultaneously, along with the final installation of the appliance in place.

You can immediately make a reservation about one point. Desktop dishwashers, in principle, can sometimes do without a fixed connection to communications. In this case, the water supply hose is connected directly to the spout (there are special adapters for this), and the drain hose is lowered and fixed in the sink bowl.

Dishwasher

Sometimes such a scheme is presented almost as an outstanding advantage - they say that the owners have the opportunity to economically use the countertop space, taking it out of storage and installing the dishwasher only as needed.

Let me disagree with these "merits":

• First, it is unlikely that such owners will be found who will carry massive equipment back and forth. This is simply inconvenient, and it will not benefit an expensive device. And to use the dishwasher from time to time, "on holidays" - so why then buy it at all? She should become a faithful assistant in the kitchen, and not at all the subject of the "secret pride" of her owners.
• Secondly, from frequent connections and disconnections of the water supply hose, not a single connection will last long - neither threaded nor socketed. This is not very good for either - extra loads on the spout make it loose.
• Thirdly, the drain hose from the dishwasher lowered into the sink bowl conceals a certain danger. Inaccurate movement, sudden pressure, childish prank - all this can lead to the hose jumping out of the sink with all the ensuing (literally) consequences.
• And fourth, it's just inconvenient. Simplifying their work during the initial installation of the device, the owners greatly complicate their further operation. The operation of the dishwasher will require constant monitoring, and in addition, while the washing process is in progress, the kitchen sink is practically “paralyzed”, which may be required at this time for other needs.

So, the best way out there will still be a fixed connection to the water supply and sewerage, regardless of the type of model. Moreover, there is no tangible difference in the order of the work.

Connecting the dishwasher to the water supply

Let's start by connecting the water supply.

For starters, a little note. There is an opinion that in order to save money, it is more profitable to connect a dishwasher to a hot water supply pipe, they say, expensive electricity will not be spent on heating water to the temperature required by the washing program.

Indeed, some models of dishwashers support this option. Moreover, there are even machines that provide for connection to two mains at the same time - cold and hot water supply.

All this must be indicated in the product passport. Connecting the machine to hot water, if this possibility is not specified by the manufacturers, is prohibited. The electronics of the device may not understand this, and such amateur performance often ends with the “departure” of the programmed dishwashing algorithms.

But even if such an opportunity to choose between hot and cold water supply is provided, almost all masters unanimously recommend not to experiment, and limit themselves to the usual connection to cold water. There are a number of logical explanations for this.

- First, the quality hot water very often far from ideal.

- Secondly, it happens that the temperature of the water in the hot water supply exceeds the required heating level set for the dishwasher. It seems to be nothing terrible, but this again can “mislead” the software control unit of the device.

- Thirdly, it is no secret to anyone that problems with the supply of hot water happen many times more often than with cold water, and in summer time, during the period of repair and maintenance work in boiler rooms, there may generally be long-term shutdowns. It turns out that in such situations it is necessary to switch to hand wash dishes or immediately switch to cold supply. Isn't it too troublesome?

- And fourthly, in matters of economy - everything is also not so obvious. Modern dishwashers of class A and above are very efficient in both water and electricity, and should not “break a hole” in the budget due to electricity bills. On the other hand, if the apartment is equipped with water meters, then the consumption of water for washing dishes will have to be paid at the “hot” rate, which is also rather big.

Of course, it is up to the owner to decide, but good advice is to connect it to cold water.

Now, actually, about the connection itself. There may be several options here.

BUT. The simplest solution is when the dishwasher is installed and the length of its hoses makes it possible to connect to a pipe that has a flexible hose connected to the kitchen

To do this, all you need from the tools is an adjustable wrench, sealing winding, and you will need to purchase a special tee with a tap designed specifically for such purposes.

Such a tee has a ½ inch “female” thread for packing on the water supply pipe (pos. 1), from the opposite edge - a ½ inch “male” thread (pos. 2) for reconnecting the flexible mixer supply, that is, it provides a through passage of water. The side outlet has a ¾ inch thread (item 3) ideal for connecting dishwasher or washing machine hoses. The tap (pos. 4) makes it possible to open and close the water supply in this direction as needed.

Connecting will not be difficult.

• The valve for the general supply of cold water to the apartment is closed. Next, you can open any faucet (best located closest to floor level) to relieve excess pressure in the cut-off section of the home plumbing.
• Further, with the help of a wrench, the nut of the flexible connection of the mixer is unscrewed, the threaded part of the pipe is released. If necessary, the remnants of the old winding are removed from it.
• The next step is winding the sealing winding, in the direction of tightening the nut. For these purposes, an FUM tape can be used, but a more reliable connection is sealed with ordinary linen tow coated with a special Unipak type paste.

• A tee is tightly screwed onto the wound thread. When tightening, make sure that the side outlet with a tap is in a convenient position for connecting the dishwasher hose.

Here we can immediately note one important point. Many modern dishwashers are equipped with an "aqua-stop" system, which has solenoid valve, which will instantly shut off the water supply to the hose if there are signs of leakage (pressure drop). The body of this valve is quite large in size, and is located exactly on the side of the hose that connects to water pipe.

This means that both in preparation for work, and already specifically during the installation of the tee, it is necessary to take into account how this “aqua-stop” block will rise, whether there will be enough space for it.

• After the tee is installed, you can immediately install the flexible hose of the kitchen faucet in a new place, if necessary, changing the rubber ring gasket.
• The tap on the tee is switched to the “closed” position, and after that you can open the general water supply - it will immediately be possible to check the assembly for leaks, and if necessary, tighten it.

• The last step is to screw on the plastic nut of the dishwasher hose. It has its own o-ring, and no rewinding is required. Twisting is done without the use of any tool - a fairly well-applied hand effort.

On this, in fact, the option of connecting to the water supply directly under the kitchen sink can be considered completed. But it is worth paying attention to one more nuance.

The use of a tee scheme will be convenient if one additional draw-off point is connected. However, in practice, the space under the sink is often much more loaded. For example, hoses of a washing machine and dishwasher can be connected here, a drinking water, and even a flowing water heater (column) or boiler is often connected.

Under such conditions, the tee system does not justify itself - under the sink, a complex and heavy structure of tees and adapters is formed, surrounded by a "web" of hoses and flexible connections, which creates considerable difficulties both for control and for carrying out any preventive or repair work. It will be much more convenient to install a small collector from below, for 4 ÷ 5 outlets, connect it to a water pipe, and from it already conduct switching to all points of water intake.

Such a collector can be purchased ready-made - metal or polypropylene. For those who have at their disposal a machine for welding PP pipes, it will not be difficult to make a collector of the desired configuration from polypropylene tees very quickly - this is often even more profitable.

Dishwasher

In this case, to connect the dishwasher, it is no longer a through tee that is purchased, but an adapter with a tap.

The collector is easy to securely fix on the wall surface (with clamps or dowels), and all branched switching in the space under the sink will take on an organized look. In addition, the interdependence of connected devices operating simultaneously will be reduced to a minimum - with a tee scheme, opening water at one draw-off point usually entails a pressure drop on others.

B. The second option - the length of the hoses to the sink is not enough, it is impractical or impossible to increase them due to the peculiarities of the arrangement of kitchen furniture, but a cold water pipe passes near the installation site of the dishwasher.

The principle is simple - it is necessary, after shutting off the water, to cut a small section of the pipe, and install a tee in its place. The faucet already mentioned above is packed to the perpendicular outlet of the tee, and the dishwasher hose is connected to it.

The execution of such an alteration depends on the material of the pipe.

• If it is a metal-plastic pipe, then there is no difficulty. A fragment is cut out, and a tee with press fittings is put in its place, for packing which a set of wrenches is enough. Next - the installation of a crane with a conventional winding - and the node is ready to connect the device.

• It is not much more difficult to crash into a polypropylene pipe, however, this will already require a special welding machine. Of course, it is unprofitable to purchase it because of three or four joints, but usually such a device is easy to rent for a day or two, it is not so expensive.

welding machine for polypropylene pipes- a reliable home assistant.

To be honest, it never hurts to have your own inexpensive equipment for welding polypropylene pipes - it can bulge in various situations, it will allow you to easily and cheaply upgrade home communications. As it is right - in a special publication of our portal. And another article will help you learn quickly and easily.

When welding polypropylene on a previously assembled section, a certain backlash of the pipe is necessary in order to be able to bring mating parts into the soldering iron from both sides. This is not always possible, so it’s easier to resort to boiling out two “American” union nuts, and between them already mark a regular brass tee with a tap packed on it to connect the dishwasher hose.

fum tape

• The hardest thing will be if you need to crash into steel pipe.

- You can cut a section, cut the threads on the remaining ends, and mount a tee from it, either according to the principle of driving, or also using "American women". The disadvantage is the difficulty with threading, as a special tool is required.

- Another option is to install the so-called repair clip (shroud tee).

Such a product allows you to crash into a steel pipe in almost any convenient place on a straight section. The clip with rubber seals is installed on the pipe in the desired position, tightly tightened with bolts. Then the pipe wall is carefully drilled through the hole in the tee. Further, everything is simple - packing the tap and connecting the hose, as usual.

The method is quite simple, but, to be honest, it is not particularly praised. First, the pipe body is weakened. Secondly, cases of the beginning of leaks in this particular place are known, and it will be very difficult to eliminate them. And thirdly, a hole drilled in a pipe often becomes a weak spot in terms of clogging.

AT. Finally, the third option is when the dishwasher is located far from the cold water pipe.

To increase the length of the hoses is to increase the vulnerability of communications to possible leaks - any flexible connection is still less reliable than a stationary high-quality pipe. So, it is necessary to bring water to the machine.

Laying an additional section of the water supply to the installation site of the device is usually not difficult, and it will require little money. Another thing is how convenient it will be, and beautiful. If the pipe is completely hidden behind pieces of kitchen furniture, there are no questions.

But it is best, of course, to think through all the issues of the future installation in advance, that is, when installing home plumbing and sewerage, immediately provide for connection points for household appliances. Perfect option- This hidden gasket pipes with the installation of water outlets on the walls in the right places.

Connecting the dishwasher to the sewer

You can find a lot of articles stating that connecting a dishwasher to a sewer is generally the simplest operation that does not require any rules to be followed. Like, the drainage hose of the device is installed through a sealing rubber sleeve into a 50 mm sewer pipe socket specially prepared for it - and this issue has been resolved. Alas, not everything is so simple, and the followers of this technique may well encounter very unpleasant moments.

First of all, a water seal must become a prerequisite, otherwise unpleasant odors from the sewer will penetrate through the hose into the dishwasher.

Secondly, care must be taken to prevent water from flowing back from the sewer into the machine. To do this, the upper loop of the drainage hose must be located at least 400÷500 mm from the floor level. Where did these values ​​come from? Apparently, the level of the filled bathroom is taken into account - with a sharp release of water and some temporary problems with the patency of the sewer pipe, the water in it, according to the physical law of communicating vessels, will tend to rise to the general current level. Loop-shaped bend at the right height will not allow it to penetrate the dishwasher.

Thirdly, direct connection of the drain hose to sewer pipe using a seal makes this connection practically airtight. Oddly enough, but in this case it is not at all a virtue. Ideally, the pressure in the sewer pipes should equalize with atmospheric pressure so that no vacuum is created. Otherwise, this may result in the so-called "siphon effect" - a massive discharge of water in one of the sections causes its spontaneous current to flow to others connected to it. This leads to the fact that the pipe itself begins to "suck" water out of the dishwasher. Such a phenomenon can cause unbalancing of automation, the appearance of software errors and even equipment failure. By the way, the opposite option is not completely excluded - throwing dirty drains into the car, the consequences of which you don’t even want to think about.

But on the other hand, a leaky connection between a hose and a pipe is a possibility of leakage and spread unpleasant odors. How to do the right thing.

There are several acceptable options:

• One of the simplest, cheapest and most effective is the installation of a drain siphon on the kitchen sink with a special pipe for connecting the drainage hoses of household appliances.

As can be seen from the illustration, the siphon can also have two nozzles - if there is a need to connect both the washing and

The branch pipe usually ends with a conical fitting, the embossed, stepped surface of which ensures reliable fixation of the hose after tightening the clamp.

tap adapter

Such a connection of the drain hose, in principle, meets all the requirements listed above:

- The water seal from the spread of odors from the sewer side is provided by the very design of the kitchen siphon.

- The connection point is located at the top, the upper bend of the drainage channel is formed by itself.

- At the same time, the drain hose is not hermetically connected to the sewer pipe - it communicates with the atmosphere through the drain hole of the sink. That is, the siphon effect is completely eliminated.

• The above method is very good, but, alas, not always possible. For example, the sink is located out of reach of the dishwasher's drain hose, and a section of the sewer pipe has to be pulled. Another example is the design of the sink itself and its “branded” drain do not require any changes, and such a connection becomes impossible.

There is nothing to do, you have to connect to the sewer pipe. If its outlet is already occupied by a corrugated pipe from the sink - it's okay, you can put an "oblique" tee, reconnect the siphon, and use the second outlet for the dishwasher. And the connection here, whatever one may say, will still have to be made airtight, using a sealing rubber sleeve, otherwise an unpleasant odor cannot be avoided.

But what about the rest of the connection requirements?

The easiest way to solve the problem is to provide a water seal and ensure the required height of the loop. You can purchase a special polymer insert (they are often even included in the equipment supply), fix it in the intended place on the wall, fix the hose in it at the desired height. In this case, it is necessary to achieve such a position of the hose that a lower bend (like the letter S) is necessarily created - it will serve as a water seal.

But what about the potential threat of the "siphon effect"? There are also ready-made solutions for this.

- Installation of a simple "anti-siphon" valve on the hose.

This product is inexpensive and very easy to install. The hose is cut, and then connected by means of this valve, with tight fitting clamps. The disadvantage of the simplest device is a short service life, usually not exceeding six months. After that, you will have to purchase a new valve, since it is practically impossible to maintain.

- A more reasonable option is to purchase an anti-siphon valve made in the form of a loop. Not only does this immediately solve all the problems of proper placement of the hose - such devices are quite subject to regular cleaning, that is, they will last much longer.

A little more expensive and complicated in execution, but extremely convenient to use and meeting absolutely all requirements, the solution is to install a special wall-mounted siphon for a dishwasher (washing) machine. They are wall-mounted or hidden, of varying degrees of decorativeness, but they are united by the presence of all the necessary valve devices that ensure the comprehensive safety of connecting the device to the sewer.

The rear wide outlet is hermetically sealed to a vertically positioned 50mm sewer outlet, and the dishwasher drain hose is connected to the front outlet. In fact, it turns out a kind of analogue of a water outlet, only for the exact opposite purpose. They are usually replaced side by side, creating a special switching zone of the device.

Moreover, if you want to give such a connection node also an external “impressiveness”, then you can purchase a whole console structure, which includes a drain siphon with all valves, a water outlet with a tap, and even a power outlet. Such devices are usually equipped with decorative facade plates - both beautifully and everything you need to connect is at a glance.

And, finally, we can mention another very interesting technological solution. Some manufacturers complete their models with a special valve that provides the necessary air gap to eliminate the negative impact from the sewer. The constructive approach itself is interesting - the valve cuts into the surface of the countertop or the rear horizontal panel of the kitchen sink.

Such a valve is placed in a place where it will not interfere, covered with a decorative cap from above. From time to time, it will require maintenance, but removing the cap and cleaning it will not be difficult.

So, we have considered various option connection of the dishwasher to the water supply and sewerage. Some of them are quite simple, others will require certain knowledge and skills. However, none of them can be said to be completely inaccessible for independent performance.

In conclusion - a short video in which the master shares his experience of connecting a dishwasher. After receiving the information presented in the article, it will probably be interesting for the reader to look at and analyze some of the mistakes made by the installer. Blindly copying this is not necessary.

Video: dishwasher connection example

Installing a dishwasher with your own hands will save you 1200 - 2500 rubles. The work you have to do is not the most difficult. And yet, if there is no experience, then it is better not to take risks and call the master.

But if you purchased a portable PMM, then it is easy to install it yourself - you just need to connect the water supply hose to the faucet with cold water, and lower the drainage drain into the sink.

In general, connecting a dishwasher, located permanently, consists of the following steps:

1. Installation of PMM at the place of operation (and dismantling of the old device, if necessary);

• If you bought a built-in dishwasher, then you need to additionally mount it in the furniture and hang it in the facade - here the main difficulty is to make the markings for the fasteners correctly so that the facade is installed evenly.

1. Connecting the dishwasher to the outlets for draining and filling water (if necessary, extend the drain hose);
2. Connection to a socket (if necessary - electric installation work installation of sockets, cable laying);
3. Leveling the machine;
4. Installation quality check.

If you are confident in your abilities, then let's get started.

What do we need

Before you install a dishwasher in a niche under the countertop or connect a stationary model, prepare the tools and plumbing fittings.

Tool:

• Pliers, and preferably an adjustable wrench;
• Insulating tape (vinyl or cotton), it is wrapped around a metal thread on pliers so as not to damage the fasteners when tightened;
• FUM tape for waterproofing;
• Drill;
• Clamps.

Plumbing fittings:

• Waste siphon with 1 or 2 fittings - 2 fittings will allow you to immediately connect the washing machine;
• Tee, ¾ thread;
• The filter providing rough water purification;
• ball valve;
• Hank connecting pipe.

Connection Features

So, step-by-step instruction how to connect a dishwasher step by step:

1. If you are installing a built-in PMM, then first you need to prepare a niche, which, as a rule, should be 60 cm wide, and for narrow models 45 cm. You can level the machine with the level of the cabinets by removing the countertop and adjusting the legs of the lower cabinets. You also need to drill holes in the cabinet body for drainage, water intake hose and electrical wires.

• Installing a dishwasher hob prohibited;
• The place for installation is chosen so that the length of the drainage hose does not exceed 1.5 meters. It is allowed to increase the length up to 5 meters, but in this case it will be difficult to guarantee the stable operation of the equipment.

1. The next step is connecting to electricity. Please note that the socket must be of the "euro" type. You need to replace the socket if it does not meet the standards (but not the plug of the machine). Do not forget that when connected, we ensure safety, and the dishwasher is characterized by significant energy consumption. This determines the ban on the use of tees and extension cords. Installation of the outlet involves the use of a wire with a diameter of more than 2 mm. In addition, in the electrical panel is additionally mounted circuit breaker at 16A. Grounding is also performed using a 3-core wire, and it cannot be brought out to the pipes.
2. Next - connect the dishwasher to the water supply. To do this, the water is shut off, a tee is connected to the pipe, then a filter, a ball valve and a hank. All threaded joints are insulated with a fumka - it must be wound at least 10 layers.

It is also mandatory to install a coarse filter, as it will prevent sand and rust from entering the machine from the water pipe.

1. As for connecting the equipment to the sewer, here you can go the simple way by installing a siphon with an additional outlet and valve. In order to protect the device from water ingress from the sewer pipe, it is necessary to place it in a special way drain hose- at the exit point to the sewer network, it is placed at a height of 600 mm along the wall, and then bent to ensure water flow.

1. The final step in connecting the dishwasher is to check the device for operability. In this case, the machine is tested idle, controlling the rate of water inflow, its heating, as well as operation in the drying mode. The check is carried out without dishes, but with the obligatory addition of regenerating salt and detergents.

A dishwasher makes household chores much easier, as you do not have to spend time washing dishes. In addition, modern dishwashers save water, especially if many people live in an apartment or house.

You can connect the dishwasher yourself, almost without resorting to the help of professionals, for this you first need to choose a place for it. AT modern furniture there are niches for the dishwasher, if the cabinet was purchased first, and then the equipment, then you will either have to redo the design or select a dishwasher of the right size.

You should install a grounded euro socket in the kitchen, it is best to bring a separate feed-through cable to it, which is connected to the drive shield. If a person is not particularly versed in electrics, then it is best to hire a specialist to lay the cable and connect it.

The dishwasher is connected to the water through a special outlet pipe, for this:

• A filter is first installed on the pipe, which traps rust;
• After it, a shut-off valve is installed;
• And after that, the hose is connected.

For greater sealing of joints, it is necessary to use FUM tape. There is a connection for draining water through a siphon, which is equipped with an additional outlet, and the drain hose is fixed on the furniture or on the wall, at a height of about 50 cm, after which it descends to the water distributor.

This position is necessary in order to dirty water from the sink or siphon did not enter the drain hose.

Naturally, all work must be carried out in compliance with safety regulations, when laying the cable and connecting it, the apartment or house must be de-energized. Also, when connecting to the water supply, taps must be closed.

Do-it-yourself dishwasher connection technology

For many people, a dishwasher is no longer a luxury, but a necessity, especially if the family is large and you need to wash after eating a large number of utensils. In order for this Appliances served enough long time, it must be connected correctly, and almost all installation work is quite possible to do it yourself.

It is enough to connect a euro outlet to a regular one with a cable through a machine, but this is only possible if both of them are grounded in the house, if not, then you still have to lay an additional line.

For a cold water pipe:

1. A tee or even a quadruple is installed (naturally, the water must be shut off) with a tap, one branch will just feed the dishwasher.
2. If a quadruple is installed, then you can also power the washing machine at the same time.
3. Before the faucet, a filter designed for coarse cleaning should be installed.

The waste hose is connected directly to the sewer pipe using a tee, provided that the pipes are plastic, as this facilitates installation, or is connected to a special siphon with an additional outlet.

When all the connections are made, you should check the operation, for this the water opens, the dishwasher turns on, and the test mode starts. If this is not the case, then simply the shortest dishwashing mode. You should make sure that there are no leaks anywhere, and the machine works as it should.

Instructions: how to connect a Bosch dishwasher

To connect a Bosch dishwasher, it is not necessary to call a specialist, you can do all the installation work yourself, since now almost all household appliances are quite simple and do not require any special skills and abilities. To properly connect the Bosch dishwasher, you must follow certain steps.

It is forbidden to use extension cords powered from ordinary household sockets to connect the dishwasher.

Determination of the most optimal place for it, it should be convenient for controlling the dishwasher, as well as such an arrangement that it is close to the water supply and drain pipe or siphon (distance no more than 3 m). An electrical connection should also be provided, since the cord for many dishwashers is small, it should be provided for the installation of a separate and always grounded outlet.

Instruction:

1. A branch is made from the main water pipe using a tee made of high-quality material.
2. If the pipes are plastic, then the branches are also made plastic pipes that are soldered to each other.
3. It is better to use a special manifold instead of a tee.
4. The drain hose to the sewer must be connected in such a way that there is no backflow of water into the machine, and also that a water seal remains in it, which will prevent unpleasant odors.
5. It is better and safer to connect the drain to a special siphon that has the necessary branch for this.

Built-in dishwasher connected Bosch machine Pretty simple except for one thing. It is necessary to put the gasket in the hose that is connected to the water supply exactly according to the instructions, otherwise leaks in the connection cannot be avoided.

How to properly connect a built-in dishwasher

The built-in dishwasher is connected in almost the same way as other models. The advantage of this model is that this type of machine is built into kitchen furniture, taking up a minimum of space in the kitchen. Hence its name came from the word built-in. Some models are fully built into the kitchen furniture, and are closed with decorative doors, while others may partially protrude outside. When installing such a dishwasher model, you should follow the advice.

It is necessary, together with the purchase of a dishwasher, to choose furniture for it, it will the best option. If furniture is purchased first, and then it is planned to purchase a dishwasher, then when choosing, provide a place for attaching the latter.

All connections, both to power supply, as well as to water supply and sewerage, should be made following the instructions. If you connect it, neglecting the rules, then leaks may subsequently begin, and even this may sooner or later lead to the failure of the dishwasher. The connection to the mains power supply must be carried out only through a special socket with grounding, this will prevent electric shock. Equally important is the connection to the drain, the hose must be connected to the sewer so that its height is not less than 50 cm. Otherwise, sewage may be thrown into the dishwasher. The dishwasher itself must be firmly fixed and leveled, this will also ensure the normal operation of the machine.

How to connect a dishwasher with your own hands (video)

Each person can connect any dishwasher to all communications independently. Moreover, you can connect a desktop and compact dishwasher without the involvement of a specialist.

from 900 rub.

Diagnostics with repair - free of charge, without repair - 300 rubles.

Warranty 1.5 years. If the equipment fails again during this period, the master will perform its repeated repair free of charge.

Master goes to convenient time customer, 7 days a week, including holidays

The exact cost will be announced BEFORE work begins.

Parts original, guaranteed

Stock . We have a cool promotion "For a photo of a breakdown - 500 rubles!"

Do you need to connect your dishwasher quickly and inexpensively? Contact Our Master! We work with Ariston, Siemens, Electrolux, Bosch, Indesit, Zanussi, Beko, AEG and other brands of equipment.

freestanding dishwasher built-in dishwasher dismantling a freestanding machine dismantling of the built-in machine extension of the drain-gulf water hoses (price per 1 m) electric cable extension (price per 1 m) installation of the Aqua-Stop system hanging facades

Services list	Price
Connection to ready-made communications:
from 900 rub.
from 1100 rub.
Full connection with preparation of communications:
from 1800 rub.
from 2000 rub.
Connection with the preparation of plumbing communications	from 1300 rub.
Connection with the preparation of electrical communications	from 1300 rub.
Additional work:
from 300 rub.
from 200 rub.
from 130 rub.
from 100 rub.
from 600 rubles
from 350 rub.
Departure of the master	For free*
Departure outside the Moscow Ring Road for more than 40 km (price per 1 km)	from 20 rub.

* the departure of the master and the diagnosis of the malfunction are free of charge, but in case of refusal to repair, you will need to pay 300 rubles.

Stages of work

telephone consultation

Departure of a specialist for diagnostics and cost calculation

Carrying out work with the consent of the customer

Acceptance of work and settlement

Installing a dishwasher: types of work, materials used, price

During the installation of equipment, our specialists perform the following operations:

• base leveling. All existing floor defects should be compensated, because for correct operation the dishwasher requires a strictly horizontal surface;
• embedding. The master prepares the space for the equipment and makes the wiring of communications, while providing for the presence of gaps around the equipment;
• water supply. A stopcock is installed, if necessary, a drain tee is inserted and the hose that connects the machine to the pipe is extended;
• drain. At this stage, specialists connect the dishwasher to the sewer. It is possible to attach a special hose to a sink or bathtub;
• power supply. If possible, the specialist will use a dedicated line, as this allows you to protect the equipment from short circuits and voltage surges.

At the request of the client, it is possible to install a system to protect against leaks. After completion of all operations, a test run is necessarily carried out to check the operability of the machine and the tightness of the connections.

Various materials are used in the connection process of the dishwasher, including ball valve, water purification filter, electrical cables PVS, grounded socket and switch.

We offer fixed price services:

• for standard connection (including all necessary materials and parts) - 2500 rubles;
• for a simplified installation (if there are ready-to-work - drain, water outlet, etc.) - 1000 rubles.

The nuances of installing and connecting the dishwasher

Built-in appliances can be installed simultaneously with the assembly of the kitchen or in an already used set. If the location of the dishwasher is not thought out at the project stage, the master may have some difficulties. You can simplify and reduce the cost of installation if you know about some of the intricacies of embedded technology:

• It is a mistake to leave the outlet and the water drain pipe right behind the future dishwasher. The technique completely occupies a standard depth module, so there should be nothing behind it. Communications should be left behind the next cabinet.
• No separate module is required for installation. Enough free space between two cabinets.
• Equipment of this type is attached to the countertop. For this reason, you should not plan to place it next to a sink that has a large drain. Difficulties are also caused by embedding in a column with other equipment.
• All dishwashing machines have a hinged door with a handle at the top. If you are buying a kitchen and plan to buy more appliances later, order a suitable facade.
• The well-known IKEA store does not have 45 cm wide modules. Therefore, the installation of small-sized equipment is carried out without problems in a 50 cm cabinet.

If you have not taken into account the listed nuances, this does not mean that installing a dishwasher in your kitchen is impossible, but the cost of solving a complex task may increase.

Installing a dishwasher yourself or with the help of a wizard?

To perform the installation of built-in appliances, you need to have the skills of a furniture assembler, plumber and electrician. If you have a similar experience, you can save on the services of a specialist. Otherwise, it is better to practice on a different, simpler technique.