In order to ensure uninterrupted operation of water production, it is necessary to install special equipment. Pumps Dzhileks Vodomet for pumping water, you can install with your own hands near the mouth of a source of drinking or technical water.
In addition, Dzhileks Vodomet pumps for pumping water from a well can be immersed under the surface of the water table. This one is able to extract the required volumes of water from a do-it-yourself well and supply it to the house, outbuildings, greenhouses or gardens.
1 What is the design of Dzhileks Vodomet pumps?
The Gileks Water Jet pump for water extraction is presented in the form of a multi-stage unit, the principle of operation of which is based on the active use of centrifugal force. All Dzhileks Vodomet pumps for pumping water are equipped with floating wheels and a washed motor. A do-it-yourself unit can reliably supply water from:
- reservoir;
- open reservoir;
- Wells.
Due to the presence of floating wheels, the Dzhileks Vodomet pump for pumping water has enough high rates hydraulic efficiency. Reviews about such a pump, for the most part, are only positive.
The technical characteristics of the Jilex Vodomet devices are quite high, this is also evidenced by user reviews. Thanks to a number of design improvements, the Dzhileks Vodomet pump has a fairly compact axial dimensions of the body and a low weight of all rotating working elements.
The consequence of all this is a significantly reduced level of vibration of the unit during its operation. In addition, it will not be difficult to disassemble such a pump with your own hands and repair it.
The use of floating wheels in the pump contributes to the minimum number of blockages that occur due to the ingress of large particles into the system.
In addition, the electric motor of the pump is well protected against sudden overheating. The characteristics of the device allow washing the engine with a stream of water in order to cool it.
In addition, the presented pump can be installed in the well with your own hands. Repair of this unit can also be done by hand.
Feedback on the installation of the pump with your own hands and how it was repaired will help you figure out how to properly carry out the procedure for such work.
The engine is located above the pumping part of the device. Such a feature constructive solution allows you to output the power cable directly from the .
Due to this, the pump can be mounted in a well with a minimum working diameter, and it can be easily repaired if necessary.
It should be noted that the presented layout of the pump has proven itself well in cases where the design is used and when it is partially submerged.
The unit itself consists of two main parts - this is the engine and the pump compartment, which is located in a common housing. All other moving parts and elements of the unit are centrally fixed in the housing using a special intermediate support.
It also uses the front and back covers. The pump is designed in such a way that the floating wheels included in it can approach each other.
Due to this, there is a significant reduction in the gap between the parts of the device that are in a movable state and the fixed parts.
This solution avoids the occurrence of internal leaks and, in general, has a positive effect on increasing the efficiency of the entire system.
All presented units, depending on the types of marking, have a different number of repeating steps. All parts in the device are divided into four subspecies. This:
- Impeller.
- Cup.
- The bottom of a glass.
- Anti-friction washer.
The glasses are made in the form of cylinders made using black polyamide. Each of them is equipped with a belt that rests against the ring.
The ring is inserted into the spacer located in the body. An anti-friction washer is located between the glass and the impeller; it is designed to prevent friction of the mechanism parts.
The whole system is based on the rotation of the impellers located in the glasses. The cylinders are fixed and do not move due to the fact that they are fixed between and the cover.
1.1 Types of models
All units are divided into three main categories. These can be pumps for extracting water from a well; a special cooling jacket is supplied with such devices.
In most cases, the systems are used in the arrangement of private houses or suburban areas. Downhole type units are used to provide water supply from those wells that have a large diameter.
In addition, such pumps are used in all kinds of tanks and reservoirs. Chastotnik type systems are widely used in areas where uninterrupted water supply is required in automatic mode.
As a rule, these are cottages and suburban areas. An important advantage of such a device is the ability to provide the desired level of pressure in the entire water supply line.
The pressure level is not affected by the number of points from which water is drawn. Feedback on pumps is mostly positive.
1.2 Specifications and reviews
Here are some specific parameters of the most common models.
Water jet pump "Prof 60/32"
In this series, the overall performance of the unit has been significantly improved. It is used to extract water with a large amount of sand diluted in it.
- Well depth: 30 m;
- Power: 470W;
- Pressure inside the system: 3.2 bar.
Water jet pump "Prof 60/32" A
The presented model is capable of pumping not only from wells, but also from wells, reservoirs and reservoirs. It is actively used for watering vegetable gardens and orchards. There are restrictions on the on-off cycles of the device - no more than 20 times per hour.
- Well depth: 25-30 m;
- Maximum pumped liquid temperature: +40 °C;
- Power: 500W;
- Pressure inside the system: 3.4 bar.
Water jet pump 60/62 A
A submersible type unit that can pump water from great depths. Carries out supply from deep wells, is used for irrigation and watering.
- : 52 m;
- Maximum pumped liquid temperature: +35 °C;
- Power: 630W;
- Pressure inside the system: 3.6 bar.
Vladimir, 43 years old, Ussuriysk:
I decided to equip my own yard and took up the water supply system. On the advice of a neighbor, a submersible pump Dzhileks Vodomet was installed in the well. While everything suits, water is supplied with great pressure.
Sergey, 50 years old, Voronezh:
I live in a private house, the forces are no longer the same as to constantly turn the handle of the well and carry full buckets of water. He equipped the well with a special well pump Vodomet. Now it is not at all difficult to get water, the pump pumps perfectly. I am satisfied with the purchase, I advise everyone!
Pavel, 37 years old, Saratov:
I have been installing water supply systems and related equipment for several years. All the clients to whom I installed Gileks Vodomet units were satisfied, there are no complaints.
1.3 What models of Vodomet pumps are there? (video)
2 The most common malfunctions and their repair
One of the most common unit malfunctions that require repairs is that when the device is turned on, the pump does not pump water.
If you listen carefully, you can sometimes hear a barely noticeable buzz. Sometimes the device does not make any sounds at all and can be shocked at the moment when the user touches its case.
All these signs indicate that there was a partial abrasion of the covers located between the stages and the impellers. In order for the unit to work again, it must be completely disassembled and worn out impellers and covers must be replaced.
In addition, another cause may be a faulty capacitor. In such cases, the incorrect operation of the device is due to the ingress of water through the cable passage into the cavity of the capacitor compartment.
A faulty capacitor is subjected to mandatory replacement. In the event that when the start button is pressed, the pump does not turn on, first of all, you should make sure that there is voltage in the electrical network.
First of all, the integrity of the cable, which provides power to the unit, is checked. It happens that the control panel of the device fails.
In this case, it is almost impossible to make repairs on your own. Here you will need the help of a qualified specialist.
You should also act if protection is often triggered, which is activated in the event of a breakdown of the power cable and leakage of electricity.
If, during start-up, the device turns on, but does not pump water, check that the valve is installed correctly.
In this case, the pump must be lifted out of the well and make sure that the valve is installed properly. Sometimes it happens that an air lock forms inside the unit.
To eliminate it, it is necessary to immerse the pump to a greater than usual depth. In this case, the valve is installed at a height exceeding 1 meter.
Another reason for such a problem may be improper installation and installation of a check type valve. In this case, the pump is also removed and the check valve is reinstalled.
If, when the system is turned on, a partial supply of water is produced and its pressure constantly weakens, then, most likely, the equipment was operated without turning off for quite a long time. The reason for the low pressure is a clogged cleaning filter.
If it is clogged, the filter is disassembled and cleaned. Otherwise, it is completely replaced.
During the intake of water, the pump in some cases gets a large number of sand. In such a situation, the unit is placed in a container with water and it is pumped.
In order to avoid such moments in the future, you need to take care of installing an additional cleaning filter. If the equipment has completely stopped pumping water, then first of all the unit should be de-energized and removed from the well in order to conduct a detailed inspection.
With such a breakdown, the cause may be a significant decrease in the water level in a well or well. It is necessary to immerse the pump to an even greater depth.
In some cases, equipment jamming occurs. Often this is observed with severe contamination of all channels. If it is not possible to eliminate the cause with your own hands, then you should contact a qualified specialist or a service center.
The pump "Vodomet" for a well is a multi-stage equipment with floating impellers washed by water. Water cooling is one of the important factors which prolongs the life of the device.
Description
The design includes a built-in condenser, which is necessary for supplying water from the well. His inner diameter may be 100 mm or more. It is noteworthy that such a device is suitable for working in wells that contain an increased amount of sand. These pumps can be used with control by the level of filling the tank or by the level of liquid pumped out of the system. automatic control by pressure. Not only a well, but also an open reservoir, as well as a well can act as a source of water supply.
Feedback on the choice of model
If you decide to purchase a Vodomet pump for a well, you should be aware of the criteria by which this equipment is selected. According to users, it is important to pay attention to the numerical designation, the first digit indicates the maximum one minute output in the absence of flow resistance. Looking at the second number, you can understand what is the maximum head in meters developed by the equipment when working "to a dead end".
If you have a pump of the Vodomet 60/52 brand in front of you, then, according to buyers, this indicates that with a free spout, the equipment is capable of supplying 60 liters of water per minute. This volume is equivalent to 3.6 cubic meters per hour, while when the supply is cut off, the pressure will be 52 meters, that is, 5.2 atmospheres. This unit is almost never used in the limit mode, most often it is operated at the operating point.
The pump "Vodomet" for a well with a maximum flow rate of 115 liters per minute is used for wells and wells with an increased and average flow rate. If there is a need to select equipment for water sources with a high flow rate, then you should purchase an option with a maximum flow rate of 150 liters.
General characteristics of submersible type devices
The submersible pump "Vodomet" for the well has a high coefficient useful action he is ready to serve long time. This equipment has a powerful electric motor cooling system. The design of the pump has a cable that can be pulled through the top cover, which allows the equipment to be used in wells of even the smallest diameter
It is noteworthy that the data submersible pumps can work continuously for a long time, this became possible due to the presence of a built-in water "shirt". It provides water passage between the motor stator and the housing. "Water cannon" is capable of supplying liquid from shallow or great depths. The devices have good tightness and are equipped with a thermal protector, which is responsible for the temperature of the equipment.
Characteristics of the pump brand "Vodomet prof 60/32"
If you are interested in the products of the brand "Vodomet", the pump for the well "Prof 60/32" can be purchased by you. It belongs to the high performance series. Such equipment is suitable for water with a significant sand content. It can only be used in those wells whose depth does not exceed 30 meters. The temperature of the liquid should not be more than 35 degrees.
Consumers who decide to purchase this equipment should be interested in the power of the submersible pump, which is 470 watts. In one minute, it will be able to produce 60 liters of liquid, the maximum amount of pumped sand will be equal to 2 kilograms per cubic meter of water. The products of the brand "Vodomet" have long become popular with Russian consumers, the pump for the well "Prof 60/32" is a confirmation of this. Its body is made of high quality stainless steel, which ensures a long service life of the device. However, in the process of using the unit, you must remember that the pressure should not be higher than 3.2 bar.
Characteristics of the pump brand "Prof 55/50"
When you visit the store, you can find large assortment goods that are manufactured under the brand "Vodomet". The 55/50 well pump can be considered as an example. The depth of its immersion is 30 meters, the power is 680 watts. The equipment must be installed vertically. As practice shows, the engine runs silently, and it is capable of pumping out 3.3 cubic meters per hour. Do not use this equipment for dirty water, otherwise it may be damaged. The size of the particles to be filtered can be up to 1.5 mm and the length of the power cord is equivalent to 20 meters. This information will help you when installing the device.
Characteristics of the pump brand "Dzhileks Vodomet 115/115"
If you are interested in the Vodomet brand, you can purchase a pump for a well 115/115 for 14,300 rubles. This submersible equipment is designed to pump water from a well, while the liquid may be slightly contaminated. The maximum depth, as in the above case, is 30 meters. Productivity is 6900 liters per hour. The advantage is that the device can also be used for small wells. With it, you can water the garden or garden, among other things, it is suitable for water supply in homes. The weight of the unit is 22.6 kilograms, which makes it easy to install.
This pump "Dzhileks" for a well, the photo of which is presented in the article, has a fairly wide area of use. It can be used in tanks, as well as open reservoirs. The equipment is perfectly adapted to difficult Russian conditions. To create it, the manufacturer uses durable and wear-resistant materials. For example, granite and ceramics are selected for. With regard to such important element, as impellers, a wear-resistant polymer is used for them.
The range of products manufactured by GILEX includes several models borehole pumps with different specifications. This equipment is intended for use as part of domestic and industrial water supply systems with water intake from wells and boreholes. According to users, well pumps from JILEKS LLC are among the best on the Russian market.
Rules for choosing pumping equipment
Efficiency autonomous system water supply with forced water supply depends on the compliance of the technical characteristics of the pumping unit used with the conditions of water use. To do this, it is necessary to make a thorough analysis of all the nuances of the upcoming operation even before ordering the equipment. If you are faced with the question of which well pump is better to choose, consider the following criteria:
- well flow rate and volume of water consumption, the maximum number of inclusions per hour;
- temperature of the pumped liquid;
- parameters of the existing electrical network;
- water quality, presence and size of mechanical impurities;
- possible immersion depth for the submersible unit.
One of the most popular borehole pumps of the company "JILEKS" is a submersible centrifugal unit "VODOMET". This equipment is available in several modifications, which allows you to choose a device with optimal technical characteristics for specific conditions of use. Each model is distinguished by high reliability, unpretentiousness, efficiency, and has a high efficiency. When choosing, use the online consultation of our company's specialists. Channels for communication are given in the "Contacts" section.
Borehole pumps Vodomet are produced in Klimovsk and are centrifugal multistage and are designed for autonomous water supply of cottages and summer cottages.
Borehole pumps Vodomet are structurally somewhat different from most borehole pumps. At "Water cannons" the water intake is not from the side, but from below. This scheme allows you to effectively deal with siltation of wells. Pumps "Vodomet" are modified to work in sandy wells and are designed for long work with sand content up to 150 gr./cu.m. In reality, they can pump several kilograms per cubic meter of water.
Water jet pump. Advantages.
A very competent self-cleaning system of the Vodomet pumps allows them to be used to supply water from wells, where the distance from the pump to the bottom will obviously be small. Such pumps are equipped with a float switch to protect the pump from running without water, and are named with the letter "A".
Borehole pump Water jet can be located at a depth of up to 30 meters from the water surface, which allows them to be recommended for low-budget wells.
| Name | Power Tue |
Production, m3/h |
pressure, m |
Price, rub. |
Diameter |
|
| 460 | 3,3 | 35 | 6000 | 98 | ||
| 600 | 3,3 | 50 | 8090 | 98 | ||
| 900 | 3,3 | 75 | 10160 | 98 | ||
| 1100 | 3,3 | 90 | 12280 | 98 | ||
| 470 | 3,6 | 35 | 7050 | 98 | ||
|
Each well in the summer cottage for supply from the depth pure water, must be equipped with a device such as a water jet pump. This device, like a water jet pump, makes it possible to receive water from a well where there is no water. Powerful specifications water cannon pumps allow you to lift water from great depths. The water jet pump is small in size, has a very simple design, and endowed with the simplest automation. 1 Features and differencesWater jet pump "" regardless of size, models are always made only at domestic enterprises. All pumps of this line are adapted to the Russian climate. And we know that water resources(highways) have never been clean in our country. As a result, even the simplest water cannon can pump the most dirty water and not fail for a long time. The channels inside the pump are practically not contaminated. The most important advantage of the pump is that it is able to clean itself. Pumps are also good because, in addition to Soviet components, you can easily pick up spare parts for them from French, American and even German production. At the same time, the price of a water jet pump is much lower than, for example, German or French counterparts. Now the pump is constantly being improved. The quality of performance is improving, the design has become an order of magnitude better. Here, for example, if we talk about the latest model of a water jet pump for a well, then in it the electric motor is located above the location of the pumping part. As a result, the Water Jet water pump has a body that is an order of magnitude smaller. It became possible to connect electrical cable to the top.
All water jet pumps for wells have a wetted motor. This means that water passes between the casing and the stator sheath. As a result, the engine is continuously cooled. The water jet pump for the well has high-quality dividing seals. These seals protect the motor and also give a complete seal to the housing. 2 Water jet pump deviceThe water jet pump for the well has a very strong power. This allows him to provide water not only for a small plot of land, but for the whole house. We will now analyze the most best models water jet pump. Submersible model WATERJET PROF 55/35
Pump submersible water jet PROF 55/50
Submersible pump water jet 60/72
Submersible pump water jet 60/52
Prices for submersible water cannon pumps for wells:
2.1 Systems of the DOM series based on the Vodomet pumpEach country cottage area, and on it private house requires constant water supply. As a result, a system was developed for a constant supply of water. It is called "Water cannon house". This system provides a constant supply of water to a summer cottage and a private house without human intervention. The system consists of:
Set of the system "WATER HOUSE":
This system provides constant water pressure. Saving electricity. Equipped with a current overload sensor, as well as a differential pressure sensor. It also has a soft start system. Related Articles Latest Articles
Editor's Choice
|
How to cook ham in the oven at home
Pain in the lower abdomen during pregnancy, reasons for what to do Can the lower abdomen hurt if pregnant
Protein for muscle gain
The best vitamins for men according to customer reviews
How to lose weight on a vegan diet?