How to install a drain hose. Inlet hose for washing machine

23.06.2020

For correct and trouble-free operation washing machine necessary competent connection washing machine to the sewer. You should know, first of all, that when choosing a place to install a washing machine, you must take into account the length of the drain hose. It is also necessary to take into account the diameter sewer pipe when carrying it to the washing machine. The diameter of this pipe is 40 mm miniaml.

For the correct and trouble-free operation of the washing machine, it is necessary to competently sewer. You should know, first of all, that when choosing a place for it is necessary to take into account the length of the drain hose and the connection diagram. It is also necessary to take into account the diameter of the sewer pipe when conducting it to. The diameter of this pipe is 40 mm miniaml.

Draining the washing machine: connection to the sewer

After completing the stage of work on bringing water to the machine, we will consider several basic options for connecting the drain of the washing machine. In any case, this issue should be taken seriously, because when the water is drained by the machine, the hose can pulsate strongly and the unreliability of the connection can cause water leaks, which can significantly spoil the mood and property not only for you, but also for the neighbors below.

Option 1. Using the latch that usually comes with the washing machine, you can fix drain hose on the bathtub board or sink. In this case, the possible height of the hose must be taken into account. It is indicated in the installation and operating instructions, usually manufacturers recommend that it does not exceed 100 cm. Otherwise, the pump power may not be enough to drain all the water. In addition, it makes sense to provide a rigid fastening of the latch, for example, to a water tap.

Option 2. The second way to connect the washing machine to the sewer is to connect the drain hose directly to the siphon. In this case, you get rid of the need for additional cleaning of the sink or bathroom at the drain.
What is a siphon? This is a curved tube through which water from the sink enters the sewer. The bend is necessary to create a water blockage that prevents penetration bad smell from sewer pipes.

There are several types of siphon designs. The simplest is a conventional flexible corrugated pipe. A special clamp is used to fix the knee. The advantages of such a siphon include low cost and ease of installation, so it can often be found in new homes.

The second, most common type of siphon is a bottle siphon. It is equipped with a special flask in which a water jam is created. In addition, if you accidentally drop the ring into the sink, it will linger at the bottom of the flask.

When organizing the drain of the washing machine, you can use special siphons, which are equipped with additional outlets for drain hoses. They can be purchased at a hardware store. When correct installation siphon, you will get a neat connection to drain the washing machine directly into the sewer. It is worth noting that this work often requires the appropriate skills and its solution should be entrusted to a qualified plumber.

Option 3. You can lay an additional elbow from the existing sewer pipe, where the sink is drained. In this case, an additional set of sewer pipes with a coupling and a reducer is required, which acts as an adapter from the drain hose to the standard sewer pipe. All connections must be strong, for this it is advisable to coat them with plumbing silicone.

Connecting and installing a washing machine

Installation and connection of the SMA consists of several operations:

Remove transport bolts, place the machine on a solid, flat surface, adjust the level of the machine.

Connecting the washing machine to the mains. If you recently had a renovation, or you live in a new building, most likely you already have a special outlet for SMA, then there is no problem. If not, then you will have to pull a separate line from your electrical panel without fail. This is the most time-consuming and expensive operation in the entire installation procedure. Would need circuit breaker 16A, wire with a cross section of at least 1.5 sq. mm., a waterproof euro socket with a grounding terminal, and, accordingly, lay and install all this.
Connecting the washing machine to water. Here you need a special tap - with a ½ x ¾ thread, or an angled or through passage, depending on the specific conditions. If the apartment has a separate water outlet for connecting the washing machine, a corner tap is installed, if not, a through tap is installed in the gap of the water outlet for cold water and flexible connection to the faucet, or toilet barrel. If the apartment does not have coarse water filters, it is advisable to install the filter in front of the water supply tap to the washing machine. Next, a supply hose is connected to the tap. If the supply hose is equipped with an aquastop device, it is recommended that it be positioned vertically. If the length of the supply hose is not sufficient, it can be extended using special materials.

The next step is to connect the washing machine to the sewerage system. There are two main ways. Connecting the nearest plumbing fixture to the siphon (kitchen sink, washbasin, etc.) in this case, the siphon is changed to a special one with a tap for the washing machine. This method has a significant drawback - if the siphon is clogged, dirty water from the washing machine will flow into the sink. However, this is a very common way. Another way to connect the washing machine to the sewer is to install a tee directly into the sewer system. This method is more preferable, does not have the disadvantage described above, but is slightly more expensive for the consumer.

And the last stage is a test run. The performance of the machine is checked, without linen, with a small amount of powder, at the same time it will be washed. It is enough to fill in water, stop the program, turn on the drain, check all connections for leaks.

washing machine connection automatic washing machine motor connection diagram washing machine connection price Processed

When buying a machine, we almost always know its future location. But it often happens that due to size or for other reasons, the place changes. The first difficulty that SM owners face is the long distance from communications. Therefore, today we will talk about whether it is possible to extend the drain hose of an automatic washing machine, and how to do it correctly.

Before extending the hose, you must understand its parameters. Remember: in no case should you raise it higher than 1 meter in order to drainage pump could normally pump out the waste water from the tank. If you neglect this recommendation, the low power of the pump will not be enough to drain, the water will linger in the tank.

During connection, you must take care of the free tension of the tube, especially paying attention to the top point. It should be 60 cm higher than the lowest point. This is typical for all cars, regardless of brand and model. But still, if you have everything calculated down to a centimeter, you need Additional Information. To find out the exact value, look at the user manual - everything is written there. If nothing is indicated in the manual, look for other technical documentation for the CM.

Usually the maximum length of the hose does not exceed two meters, and more often it is only one and a half. If the tube is much shorter, or standard size it’s not enough for you, you can go for a trick - instead of lengthening the drain hose, get a new one of sufficient length.

Attention! You can buy the part in a store specializing in the sale of plumbing, or in a service center. If you did not find what you were looking for, go to "online" - find the desired part on the Internet.

To replace the part, you have to disassemble the case. If you are not ready for such a radical action, there is a simpler solution - connecting 2 washing machine hoses. To build a drain hose, take:

One more new part.
Quality clamps.
Connector for drain hoses.

In principle, you can save on clamps if the connection is tight. But to make sure of this, you will have to visit the store repeatedly - first buy a connector, and then clamps, if there are doubts about the tightness. Also, clamps will come in handy without fail if you can’t pick up a connector.

If you bought a connector

Fix the hoses in the connector on both sides.
Secure with clamps.
Install on the machine and sewer.
Run a test wash, if everything is fine, the machine can be used.

Without connector

Find a plastic or rubber tube. Its size should be such that it fits on both hoses.
Buy clamps.
The tube is put on the hoses so that they converge in the center. The tighter the tube sits, the better.
Use clamps for a tighter fit.

If you do not have enough allowable length of 3.5 meters, then there are other ways out of the situation:

Install equipment closer to communications.
Zoom in on the drain.

Want to visually see how to extend the drain hose? We offer video:

Having figured out how to lengthen the drain of the washing machine, you have solved only part of the problem. But you still need to figure out what to do with the water inlet hose, if its length is also not enough. About all this - below.

Not sure how to extend the inlet hose? Everything is extremely simple: instead of building up a water supply hose, buy a more authentic part. It is sold in the same place as the parts for the drain system. To change the part, disassembly of the SMA is not needed. Proceed like this:

Disconnect the SM from the water supply, if it was connected to it.
Unscrew the fasteners (manually, without tools, so as not to damage the plastic fasteners).
Installing a new item. When tightening the fasteners, do not use tools - do everything manually.
Open the valve and check the tightness of all connections.
If everything is fine, proceed to washing. At least for testing.

If you can’t find a hose of a suitable length, you can lengthen it. Usually the water supply hose is extended by the second of the same element, but you will need an adapter. Use a 3x4 inch brass nipple. To extend the hose for the water supply to the washing machine, simply screw the nipple on each hose, and that's it - the job has been done successfully.

If you had to add or change parts, do not forget to check if your typewriter has enough cord to connect to the mains. If the cord is too short, or vice versa - the outlet is far away, then you need to pay attention to this moment. It is better not to use extension cords to connect the washing machine to the mains. This is fraught with serious damage: such extension filters often provoke a fire.

Now you know how the drain and intake hose of the washing machine is extended. And wherever your washing machine is, you will always find a way to successfully connect it to all communications.

This article is written for those who are ready to connect the washing machine to the sewer with their own hands. Such a decision, of course, is worthy of respect, but it has its own nuances. I will tell you about 3 options for implementing this simple task.

Preparation is the key to success

Connecting the drain is important, and we will talk about it in great detail, but first I will briefly tell you how to install the washing machine.

Of course, each new unit has detailed instructions, I will not retell it, but will only outline the most important, fundamental points:

If the machine was brought into the house from frost, give it a couple of hours to warm up to room temperature. Modern electronics are quite capricious and can fail;
Any new unit of this size is equipped with various kinds of seals and stands. They are needed so as not to damage the equipment during transportation. In the washing machine, in addition to the most cardboard box and a foam seal, there are often a few more supporting wooden bars at the bottom, such a mini-pallet. So it needs to be completely removed;
It doesn’t matter if you bought a frontal or vertical machine, the working tank in these units is, figuratively speaking, in limbo. And so that these suspensions do not break off during transportation, the tank is fixed with several rembolts.
They must be unscrewed, otherwise the device will break at the first start and the warranty will be invalid, since this moment is stipulated in the instructions. By the way, the instructions necessarily have a diagram with the locations of these bolts. The holes from the bolts are plugged with the plugs that come with the kit;

The socket must be, as they say now, of the European type, that is, with grounding;
At the last stage of preliminary preparation, the legs are screwed in, and the apparatus is set clearly on the horizon. It is desirable to expose with the help of a level.

Do not rush to throw away everything that you removed from the device in preparation. This is especially true for repair bolts for fixing the working tank. After all, perhaps the time will come and you will need to transport it somewhere again.

Since we have to deal with plumbing work, we need to prepare the necessary minimum tool.

As a rule, any good owner always has this minimum somewhere in the pantry.

You will definitely need pliers and a pair of high-quality screwdrivers, cross and straight;
The above mentioned repair bolts, in different models washers may differ in head configuration. Therefore, if you do not have a complete set of keys, it is better to take an interest in this moment in the store and immediately buy at least 1 of this key;

If a major drain installation is planned, then the sewer pipes may have to be cut to size. Professionals use a pipe cutter for this, but personally, when I encountered such a problem, I cut the pipes with a hacksaw;
Of course, gaskets and seals are included with all parts, but I always recommend additionally lubricating these seals with silicone sealant. You don’t need to spend money on a large construction tube with a gun, a small tube is enough.

Drain connection options

Now in stores, for washing machines, you can buy drain hoses of different lengths. So I do not advise you to buy too long a hose. The fact is that the pump that pumps the drains is optimally designed for the length of the hose that comes with the machine.

A relatively safe maximum is 3m. If you put the hose longer, the pump can quickly burn out.

Option number 1: for the lazy and in a hurry

For people who are absolutely far from plumbing, who are in a great hurry to connect a washing machine, there is the easiest way that does not require any financial and labor investments. Now all caring manufacturers equip their units with a semicircular nozzle on the drain hose.

You just need to take this nozzle, put it on the edge of the drain hose and simply throw this "hook" over the side of the sink, bathtub or toilet. But in the truest sense of the word, a connection, this option cannot be called it rather alternative way plum.

In addition, he has whole line bad cons:

With constant, active use of the machine, your snow-white plumbing will need to be washed frequently. After all, stocks from washing powder eat into acrylic or enamel fairly quickly;
Small sinks in the bathroom may not withstand strong pressure and large volumes of drains. And while you are watching TV, for example, dirty water from the sink will pour out onto the floor;
During draining and spinning, the pump works in jolts and the option is not ruled out when, due to these jolts lightweight plastic the hose will simply jump off the edge of the plumbing. Plus, children or pets can help this hose come off;

For those who are currently suitable for this method of draining, I can recommend tying a plastic nozzle on a hose to a faucet in a bathroom or sink with a chain. On the nozzle there is a special hole for such an attachment.

Do not forget that while washing is in progress, at least it will be very inconvenient or even impossible for you to use plumbing for its intended purpose;
And then, it's just not pretty.

I think you have convinced yourself that this simple and fast way suitable only as a temporary option. For those who are used to doing everything in good faith, I suggest considering the following two methods.

Option number 2: connecting to a siphon

Connecting the washing machine to the siphon under the sink is not much more difficult. To do this, you will only need to buy a mixer with an outlet for such a drain and a small three-quarter-inch tightening metal clamp. Moreover, now most mixers already come with such a pipe.

You will need to remove the plug from the outlet pipe and lubricate it with silicone. Then pull the end of the drain hose onto the pipe, with a clamp already put on and tighten the clamp with a screwdriver or pliers.

But there are a couple of drawbacks in this tie-in method, although they are not as radical as in the previous version:

Firstly, when the water is drained, a loud gurgling will constantly be heard from the sink, and nothing can be done about it. You may not believe it, but own experience I know that there are people who are very annoyed by this;
Secondly, it is desirable that the diameter of the sewer drain pipe be at least 50 mm. The fact is that in the kitchen, according to modern standards, it is allowed to install a drain with a diameter of 40 and even 30 mm. And with such a volume, when water is discharged, your drains will rise, and after leaving, leave a dirty sediment at the bottom of the sink.

Option number 3: tie-in to the sewer

Connecting the drain of the washing machine to the sewer directly is considered almost the most right decision. But with this option you have to tinker a little. If you, or the person who installed the sewer in your house, pre-installed a pipe with an extra branch under the drain for the machine, then everything is simple.

You need to buy a rubber o-ring and pull the plug out of this branch. Then lubricate this ring with silicone and insert it into the sewer pipe. Further, the edge of the drain hose from the machine is inserted into the central hole of this sealing ring, only you need to insert it to a depth of no more than 50 mm.

If there is no extra branch from the sewer pipe, then you will have to buy a plastic tee in which this branch is and install it yourself. Don't be scared, it's not scary.

As a rule, the sewer branch that goes to the bathroom and kitchen has a diameter of 50 mm. Next, you will need to decide where exactly the tie-in will take place and replace the tee.

That is, disconnect the siphon pipe, pull out the old pipe, change the rubber gasket and insert it into place old pipe new tee. Naturally, after that, put the drain from the siphon in its place and, according to the technology described above (through the rubber ring), cut the drain of the washing machine into the sewer.

Important little things you need to know

Let's start with the fact that the hose from the machine should not lie on the floor. On the back side, in the upper corner of almost any machine, there is a special ring or hook for which the hose should cling after leaving the unit. And from there, the drain is directed to the tie-in into the sewer.

The edge of the drain hose, whether you hang it on the bathroom or cut it into the sewer in another way, must be at least half a meter from the floor level. This requirement is mandatory for all units that do not have a so-called check valve.

Many new models are already equipped with such a valve. For all other devices, it must be purchased and installed separately. Don't worry, the price of this important detail, even the most greedy merchants do not exceed 100 rubles, and if you walk around the market, you can find it for 60-70 rubles.

Now there are several types of such valves. Personally, I prefer to take models with a locking ball. Below is general scheme such a mechanism.

Most often, such valves are used for direct insertion into a sewer pipe. But there are devices for mounting next to the siphon. Moreover, in this case it does not matter at what level this insert occurs, here you can connect to the sewer pipe even at floor level.

I had a case when a friend bought a new washer. And put the drain hose in the same place where it was embedded old typewriter, that is, into the sewer outlet located under the bathroom.

The old apparatus worked with this, but for the new one I had to buy a check valve separately. Otherwise, the water from the working tank immediately went into the sewer. Agree, it’s easier to pay a maximum of 100 rubles for a valve and install it in a few minutes than to make a separate new conclusion.

There is a common misconception that supposedly if you bend the drain hose of the washer in the form of the letter “S” and fix it like that, then you can do without a check valve. Do not believe it, you will just make an extra water seal, it will not get worse, but it will also be better.

Conclusion

I told you about options that are designed for different professional skills and financial possibilities. Now you have the right to decide for yourself what suits you best. In the photo and video in this article, this information is shown clearly. If you still have questions on the topic, write them in the comments, I will help in any way I can.

Installing a washing machine in the house includes connecting it not only to the mains and water supply, but also to the sewer system. Moreover, it is with the drain that difficulties often arise, it is easy to connect the household appliances in question to the power supply and water. To independently connect the washing machine to the sewer, you can use three methods. The technology in all cases is extremely simple. Any self-taught person can do everything, you just need to follow the simplest rules.

Necessary tools and accessories

To connect the washing machine to the sewer, you need to have three tools at hand:

Pliers.
Flat screwdriver.
Pipe cutter for plastic pipes(or a hacksaw for metal).

Wrenches may only be needed if it is necessary to extend an existing drain hose with a coupler. This will have to be done when the automatic machine is far from the sewer outlet. At the same time, it is highly not recommended to increase this flexible outlet for draining to a length of more than three meters. With a large length, the pump in the washing machine may not be able to cope with pumping water and burn out.

Necessary adapters and taps for connecting the washing machine

Of the consumables you will need:

sealing rubber;
sealant;
corrugated hose (usually included with the washing machine);
a tee or a new siphon (depending on the connection option).

To connect the drain of the washing machine to the sewer, a minimum set of tools and accessories is sufficient. Same wiring replacement or installation water pipes require much more tools.

Washing machine connection diagram

Methods

Connecting the washing machine to the sewer system is carried out:

directly to the sewer pipe through a tee;
through the connection to the siphon under the sink.

The first option is more difficult to implement with your own hands, but it is more practical and reliable. Plus, the risk of a flood when connected to a siphon is much higher than in the case of a direct connection of a drain hose and a sewer pipe.

Necessary conditions for connecting a washing machine to a siphon

At the same time, it is recommended to choose a method even when the question of how to make a sewer in a house or apartment is being decided. It is better to determine in advance a place for a washing machine. And also in advance it is necessary to provide for this technique a tie-in point in the sewer system.

Another way to drain your washing machine is to simply hang the hose on the side of your toilet or tub. In this case, even tools for installation are not required. But it is difficult to call such an option correct. Plus, you will have to look after such a runoff of water more carefully in order to surely avoid a flood in the house.

Washing machine connection

Siphon connection

It is possible to connect the washing machine to the sewerage system using a drain siphon only if it is designed for such installation. If it does not have a side outlet for connecting an additional hose, then nothing will come of it. Or it will come to change to the desired option.

How to connect a washing machine through a siphon

At the same time, if the cabinet under the sink is small in size or the washbasin stands on a narrow ceramic leg, then it will not work to drain through a siphon with a pipe on the side. Under the bowl there will simply not be enough space for new pipes.

Rules for installing a washing machine under the sink

The connection is made via a siphon as follows:

The plug is removed from the side pipe.
It is lubricated with silicone.
A hose from the washing machine is put on the outlet, over which a worm clamp is pulled.
The clamp is tightened with a screwdriver or pliers.

How to connect a washing machine to the sewer and plumbing in the kitchen

The main disadvantage of this method is the gurgling in the sink drain when the washing machine is running.

Using reduction direct sewerage

To connect the washing machine directly to the sewer, you must install on drain pipe under sink or tub tee. One of its outlets will be used in the old way for connected plumbing, and the second will go to the washing machine. You can also tie directly into the sewer pipeline or mount a tap from the riser. But these options are more complex, it is worth resorting to them only when carrying out a major overhaul.

How to properly install a washing machine

The insertion of the drain from the machine into the tee is carried out through a rubber cuff. This adapter has to be used, since hoses from washing machines and plastic fittings PVC sewer pipes for internal sewage have different diameters. If you insert the drain outlet simply into the tee, then the drains under pressure will go out of the pipeline through the clearance at the junction.

Washing machine drain connection

Other ways to drain

The washing machine can also be drained directly into a bathtub, sink or toilet. For this, almost all of the considered Appliances It comes with a hard plastic drain hose. It is designed to fix the drain sleeve on the side of the above plumbing fixtures.

When buying new Indesit, LG, Samsung equipment, there are always questions about putting it into operation. Having bought a washing machine, it is necessary to carry out work on connecting to communications. For the operation of the machine, it is necessary to organize the supply of water and drain. Such work is not difficult if you know how to connect the drain hose for the washing machine.

Functions and types of hoses

Unlike the water hose on the drain sleeve, the main function is to discharge contaminated waste water into the sewer when the machine is running. The price for them can vary from 50 to 600 rubles, depending on the variety and length.

Hoses can be of 3 types:

But the use of wastewater outlet hoses that are too long is not recommended, as this increases the risk of blockage. Possible education dead zones and even a complete blockage of the hose, which can lead to a malfunction in the machine. In addition, a hose that is too long is more likely to be damaged and deformed.

Drain hoses for machines and dishwashers more often universal ones are taken, they are made of gray polypropylene. At the ends there are fittings with a diameter of 19 and 22 mm, made of elastic rubber. One end of the hose from the washer is connected to the sewer, and the other to the device. If necessary, drain the water into a sink or bath. But you need to remember how to lengthen the inlet hose of the washing machine.

Options for creating a drain for washing equipment

The washing machine uses tap water in its work, which must be drained after washing. To do this, each device is often equipped with a special hose, which sometimes needs to be replaced. Connecting appliances to the water supply system and replacing hoses usually does not cause problems. For these purposes, the hose that comes with the washing machine is used, possibly its extension. It is connected to a water tap. It is also important to know how to lengthen the washing machine's water supply hose.

There are two ways to organize the release of the washing machine into the sewer:

Temporary drain. With this method, the drain hose is simply attached to the edge of the sink or tub while the washing machine is running.
Permanent drain. In this case, the hose is connected directly to the sewer system. For this purpose, the device includes a curved plastic guide. It is inserted and hung on the wall, and the water does not flow out of the machine under the pressure force.

Most owners of machines prefer to use a stationary permanent connection method and want to extend the hose. This method is much more convenient. First, you don't forget to hang the drain hose in your sink or tub. Secondly, this method is more aesthetic. The drain sleeve will be hidden, which improves the appearance of the room.

Removing transport parts

After the washing machine is unpacked, it is necessary to check and remove all transport parts that ensure a rigid fixation of the tank and other rotating parts, which are thus protected from damage during transport.

These parts will be bolts, holders, rods and brackets that need to be detached. It should be noted that if the machine is turned on before the shipping parts are removed, it may lead to irreparable consequences and machine failure.

The main type of transport parts are bolts. With their help, the reservoir is fixed, which, after unscrewing, should hang on the springs. This is the normal state of the tank. These holes, which remain after unscrewing the bolts, are usually extinguished by the plastic plugs supplied with the kit.

With the help of brackets, additional rigidity is required, which is necessary during transportation, and also with their help the power cord and drain are fixed. Sometimes additional transport beams are placed between the tank and the body, which can be removed after the machine is slightly tilted forward.

These transport parts that you have removed must be stored in the event that the machine is moved to a service center, in new apartment or cottage, they must be mounted backwards to avoid damage to the machine during transport.

The correct procedure for removing transport parts can be found in the instruction manual that came with your machine.

Connecting equipment to the mains

The most important condition for the operation of the machine is its safety during operation. And the correct connection of the machine to the mains is the most important point providing this. It is necessary to strictly follow the rules:

If you do not have special training and do not know what to do with your own power supply, it is better to invite electricians who service your home. They will carry out wiring that supplies all powerful household appliances, with high quality and in compliance with safety regulations. But be prepared for the fact that such work will not be quick.

An alternative to a three-wire electrical network is a two-wire cable equipped with portable device, whose operation is controlled by residual current and turns off the system in the event of a power outage.

As you can see, connecting a machine in a house may just need to be patient while doing the installation.

Machine installation process

To install washing appliances, you need to connect it not only to the mains, but also to water supply and sewerage.

On the new car there should be an instruction or diagram, where there is step by step description installation. Even if the owner of the washer has experience in implementing the machine's hose device, it is still necessary to carefully read the instructions, which describe in detail the installation of each drain hose. Incorrect installation of the drain of the machine may result in water leakage and destruction of the mechanism, and negative consequences may occur.

Necessary tools and materials:

Hoses.
Siphon.
Double hose for draining into the sewer.
Double water supply hose.
Electric drill.

In the absence of the required length of the drain sleeve, it can be increased, but incorrect and unreliable extension can lead to flooding of the apartment. It is better to purchase a hose that has the required length.

It is possible to drain water from the plastic sleeve of the equipment into the sewer system if this function is provided by fixing the pipe located on the side of the sink or bathtub.

If the drain hose is to be installed in a bathtub, it must be ensured that the water drains well. It is this discharge of water during the operation of the washer that will prevent flooding in the room if the drain hose inadvertently falls out of the structure.

The drain hose is mounted on the back wall of the washer at a height of about 80 centimeters from the end, which should not interfere with the drain. You can use another siphon.

From the second end of the sleeve, you need to start connecting with the main siphon, which prevents the ingress of odor from wastewater. This may require bending the drain hose in addition to creating a water blockage effect, but not preventing leakage to prevent odors from entering the machine.

To connect the hose in the machine, there is a restriction on the height of the outlet nozzle, minimum and maximum. To ensure high quality drainage and prevent flooding of the apartment through the car as a result of clogging of the sewer pipe, it will be necessary to leave an air gap. In this case, when washing, water will not flow into the sewer from the equipment, and the installed program will start to work incorrectly. Here you need to take into account the level of the rise of all the water in the bathtub or sink, which should be slightly lower, and the gap should be higher.

Easy connection to plumbing

Typically, the installation of a washing machine requires a water pipe at a distance close to it. The water supply network is laid using metal or plastic pipes with a diameter of 15 mm.

There are three main ways to install equipment in a water supply system:

Use of metal or plastic pipes and couplings.
With cranes.
Using a fitting for pipes made of metal-plastic.

In the first case, a compression sleeve is required, which consists of two halves tightened with four screws. The faucet is screwed when there is rubber gasket directly under the side where the hole is. After a convenient location for the connection of the coupling, it was determined that it was necessary to connect the inlet of the machine to the pipe, using a ferrule, which should compress the cold water pipe.

The technology for installing couplings involves the following actions when blocking the flow of cold water into the apartment:

Preliminary cleaning of pipes from dirt with cold water.
Tight full clamping of the four clutch screws.
Drill a hole in the pipe through the coupling using an electric drill with a diameter of 8-10 mm.
Screw the ball valve into the valve thread sealing sleeve.

It is better to give preference to a different valve design than a ball product, because its reliability leaves much to be desired. The first method is good for installing the machine in the bathroom, where access to the faucet is difficult.

Another and third installation method

The second method is suitable if the mixer and the water supply are connected using a flexible reinforced hose, in the gap of which a water faucet, namely a tee, as well as plumbing. In this case, the faucet will not affect the water supply to the faucet in the kitchen, but will ensure that the water flow only to the machine is blocked. It is necessary to use a structure similar to the first method.

The use of the third method is typical for the presence of metal-plastic pipes. Here you need a special tee or fitting. The incision is made on metal-plastic pipes, and a fitting is inserted into it, which is equipped with a tap. The tee kit is supplied with all parts to seal the device.

Connection is carried out according to the instructions. The diameter of the hose for the washing machine drain is about 34 inches. After the machine is turned off, the water flow is required to be blocked, so an additional valve must be installed to turn off the water supply. Use a strainer to remove small contaminants from the water entering the machine that clog the equipment as a result of supply through the water supply system. It's right behind the valve. From time to time, removal and special cleaning is required.

Regardless of the chosen method of connecting the drain to the sewer, immediately after completion of all work, carry out tests and lay the laundry. Then you will immediately see possible disadvantages. If done correctly, the drain system will work as long as the washing machine itself. In case of problems, you need to know how to change the drain hose in the washing machine.

Attention, only TODAY!