Improvement of the brazh columns baby and strong. Making a mash column with your own hands

There has long been a debate among craftsmen about the need for beer columns and whether they justify the cost of acquiring them or making them yourself. Let's try to understand this issue.

Unlike a distillation column, a continuous mash column operates at high speed, providing moonshine of very high strength (almost alcohol) at the outlet. She, like the rectification, rids the final product of fusel vapors.

Some disadvantages

What is a disadvantage for some is an advantage for others. However, before purchasing or making such a device (preferably from copper with your own hands), you should know something.

For the usual practice of home brewing (from time to time, in small batches), it is not suitable, since the product intended for processing (mash), the mash column requires at least 70 liters, and even better - 100-120.

Costs are necessary - either monetary or labor in order to have such a device. The need for accurate and correct regulation of temperature, water flow, etc. it is best to entrust the electronics, which in other cases causes difficulties.

If funds permit, it is best to purchase finished column, providing continuous action, equipped with electronic control. This will eliminate additional adjustments and initial errors.

How it works?

Let's consider the principle of operation of the beer column so that you can finally understand: do you want such equipment for yourself?

1. Braga is supplied to the heat receiver (upper part of the column pipe) with a pump.
2. Being in a column, begins interact with water vapor heated to almost 100 ° C in countercurrent mode.
3. going on heat exchange: alcohol evaporates, other components having a high boiling point flow down and are removed.
4. On jumpers made of mesh material, located horizontally, arises focal bubbling. Because of this, the percentage of alcohol in the vapor increases. This is what causes the high resulting moonshine.
5. are retrieved from mash in a column with liquid selection unnecessary components(sivukha), at temperatures below 76°C. The temperature must be regulated using the speed at which the mash is supplied, as well as its temperature.

The moonshine obtained in the beer column is already does not need to select either heads or tails– the final product is strong and clean from unnecessary impurities.

Design features

According to the device, the beer column continuous action at the same time reminds distiller and rectifier. Consists of:

• dephlegmator- a part that takes care of getting rid of moonshine from fusel fumes;
  distiller - in fact, a distillation device;
• refrigerator- common or separate for the reflux condenser, and for the distiller (read:);
• pump feeding the mash into the column;
• thermometers, and even better - temperature sensors.

How to do it yourself?

So that a continuous do-it-yourself mash column is not just active, but its work is trouble-free, there are many nuances to consider c, including frequency of use and production volumes.

You can see a drawing of the popular bast column Malyutka below. It's not that hard to implement. The name itself already speaks of its compact size. However, it is worth knowing that "compact" does not mean low.

Column height should not be lower than 1.5 meters, better - about 2 meters. With a lower design, it will not provide a high-quality selection of alcohol vapor, and a significant amount of it will go to waste.

A feature of the Baby is that the condenser and reflux condenser are located in the same refrigerator, that is, the container with running water is the same for them. This, of course, saves costs and partly - materials.

However, this design has a drawback - it is quite difficult to regulate the reflux process and you may be dissatisfied with the quality and strength of moonshine. Of course, you can get medium quality alcohol, but you want to be known as a true master of a quality product.

This will help the beer column of Maris, or as it is also called - Modernized. Refrigerators in it for the reflux condenser and distiller are separated and it makes it possible, with proper adjustment, to obtain rectified alcohol, free from unnecessary impurities, with a strength of up to 97%.

Necessary materials

Familiarize yourself with the diagrams for self-manufacturing before starting work, it is necessary to purchase devices and materials. You will need:

• container for mash with a capacity of 100 to 200 liters;
• one - two containers for arranging refrigerators, depending on the chosen design or materials that allow you to make it yourself;
• a pipe with a diameter of at least 50 and not more than 100 mm made of stainless steel or copper with a height of 1.5 to 2 meters;
• mash pump;
• to control the beer column, a voltage regulator of the LATR type is needed;
• thermometers (2 pcs.);
• heating element (if provided);
• fitting, according to the drawing;
• screen partitions-filters;
• silicone hoses.

Naturally, in order for manufacturing to be possible, you must also have tools and fixtures for installation.

Now you have learned what a beer column is and how to use it to get moonshine with excellent (let's be honest - unthinkable with other methods) indicators of strength and purity. Easy to make and fun to use!

At the end of November 2010, I went to the site homedistiller.ru. I was carried away by the topic of moonshine, read, looked, became interested in how masters of intoxicating crafts make interesting models of moonshine stills, distillation columns with their own hands, ... Together with them, I analyzed the principle of operation of one of the existing devices , considering his image in the photographs, in a specially dedicated forum thread http://homedistiller.ru/forum/index.php?topic=13314.0 It so happened that looking at one photo, various assumptions and new schemes arose in the imagination of the members of the forum. One of them I liked so much that I wanted to bring it to life. Compactness, ease of manufacture and minimum prices for components - all these factors further contributed to the manufacture of a new model of moonshine. Thus, I became obsessed with this idea and began my journey to make an interesting product. I had to pick up and buy everything necessary materials in stores, starting from the lower part - a stainless steel tank and ending with the upper part of the device - a glass jar of a steamer. And so, the day came when I assembled the model according to the scheme and tested it on water distillation. The first results were negative. It was necessary to analyze several options to resolve the issues that arose. And this path was overcome by me together with the forum participants. Thanks to my forum friends, I managed to improve the product, bring it to working condition, improving the performance of my device with each test. In addition to the creative work done, I learned new technologies for the manufacture of various alcoholic beverages. This is how my little moonshine still was born, which was named by the author of the scheme, a forum member by the nickname MOUNTAIN - the beer column Baby. The last two runs of the mash and one run of diluted moonshine were more than successful. The strength of the resulting moonshine can be adjusted depending on the speed of distillation. At a low speed, keeping the temperature in the steamer at 78 degrees Celsius, we get the strength of moonshine - 94 degrees; at a higher distillation speed, we get moonshine with an average strength of 75 degrees. The distillate is wonderful in every way. The chemical composition of three samples, obtained in the chemical laboratory of St. Petersburg, confirms the quality of the product. The results of chemical analyzes are summarized in a table and published, - answer 594, at: http://www.homedistiller.ru/forum/index.php?topic=13314.580 Now everyone can collect beer column Little handmade. The assembly sequence is described in detail at: http://forum.homedistiller.ru/index.php?topic=13314.640 I express my deep gratitude to everyone who helped me make my device.

At the end of November 2010, I went to the site homedistiller.ru The reason was ordinary curiosity. But I was so carried away by this topic that as a result I built this device. Together with the members of the forum, I analyzed the principle of operation of one of the operating foreign devices, considering its image in the photographs, in a specially dedicated forum thread
It so happened that, considering a very expensive and advanced distiller, various assumptions arose in the imagination of the members of the forum about its principle of operation and new schemes appeared for a new apparatus of a completely different design. I liked one of them so much that I wanted to do it myself. Compactness, ease of manufacture, minimum prices for components - all these factors further contributed to the realization of my dream. Thus, I became obsessed with this idea and began my journey to make an interesting product. I had to pick up and buy all the necessary materials in stores, starting from the bottom part - a stainless steel tank and ending with the top part of the device - a glass jar with a steamer. And so, the day came when I assembled the model according to the scheme and tested it on water distillation. The first results were negative. It was necessary to analyze several options to resolve the issues that arose. And this path was overcome by me together with the forum participants. Thanks to my forum friends, I was able to improve the product, bring it to working condition, improving the operating characteristics with each test. In addition to the creative work done, I learned new technologies for the manufacture of various alcoholic beverages. This is how my little moonshine still was born, which was named by the author of the scheme, a member of the forum Leonid, by the nickname MOUNTAIN - the beer column Malyutka. After upgrading my first variant, I carried out regular tests. I understood how it is possible to get a drink with a strength of more than ninety degrees on this apparatus. But since I do not pursue the goal of making a drink of such a strength, I decided for myself to make it no more than eighty degrees. In this case, the distillate retains the taste of the original raw material, for which I use invert sugar fermented with wine yeast. The drink is amazing in every way. The chemical composition of three samples, made in the chemical laboratory of St. Petersburg, allows you to use this product without risk to life. Results published, response 594, at:

At the end of November 2010, I went to homedistiller.ru
The reason was simple curiosity. But I was so carried away by this topic that as a result I built this device.
Together with members of the forum, I analyzed the principle of operation of one of the operating foreign devices, considering its image in photographs, in a specially dedicated forum thread http://homedistiller.ru/forum/index.php?topic=13314.0
It so happened that, considering a very expensive and advanced distiller, various assumptions arose in the imagination of the members of the forum about its principle of operation and new schemes appeared for a new apparatus, of a completely different design. I liked one of them so much that I wanted to do it myself. Compactness, ease of manufacture, minimum prices for components - all these factors further contributed to the realization of my dream.
Thus, I became obsessed with this idea and began my journey to make an interesting product. I had to pick up and buy all the necessary materials in stores, starting from the bottom part - a stainless steel tank and ending with the top part of the device - a glass jar with a steamer.
And so, the day came when I assembled the model according to the scheme and tested it on water distillation. The first results were negative. It was necessary to analyze several options to resolve the issues that arose.
And this path was overcome by me together with the forum participants. Thanks to my forum friends, I was able to improve the product, bring it to working condition, improving the operating characteristics with each test.
In addition to the creative work done, I learned new technologies for the manufacture of various alcoholic beverages.
This is how my little moonshine still was born, which was named by the author of the scheme, a member of the forum Leonid, by the nickname MOUNTAIN - the beer column Malyutka.
After upgrading my first variant, I carried out regular tests. I understood how it is possible to get a drink with a strength of more than ninety degrees on this apparatus.
But since I do not pursue the goal of making a drink of such a strength, I decided for myself to make it no more than eighty degrees. In this case, the distillate retains the taste of the original raw material, for which I use invert sugar fermented with wine yeast.
The drink is amazing in every way. The chemical composition of three samples, made in the chemical laboratory of St. Petersburg, allows you to use this product without risk to life. Results published, answer 594, at: http://www.homedistiller.ru/forum/index.php?topic=13314.580
Now everyone can assemble this beer column with their own hands. The assembly sequence is described in detail at: http://forum.homedistiller.ru/index.php?topic=13314.640

No one on Earth knows for sure who, where and when was the first to try to distill from fermented food product alcohol. The custom of home brewing goes back to ancient times. And now the beer columns or moonshine can be freely bought in retail chains.

There are dozens of varieties of moonshine stills on the market. The principle of their work does not differ from the work of a rectifier, only they are much simpler and strengthen the strength of the original product. Technically column the wash has the form of a piece of stainless steel or copper pipe with coolers. From 25 mm to 50 mm in diameter. The device can be mounted by hand. Therefore, some artisans construct the bast column themselves.

Varieties of mash columns

Moonshine stills are of two types:

• Packed.
• Headless.

A beznasadochny column is the very first and simple moonshine still. A copper sukhoparnik is installed on the "cube" with mash. Due to the high thermal conductivity of copper, part of the steam condenses on the surface of the steamer and returns to the "cube". This helps to strengthen the final product. The column with a water reflux condenser is a modern and perfect version of a non-packed column. A dephlegmator is a device, which is also called a sump, which separates fusel oils and other impurities. With some distillation skills, you can get a quality product.

packed column

Columns of this type are of three types:

• Dish-shaped.
• Packed.
• Continuous mash columns.

plate column used to obtain a high quality product. Its peculiarity: low ability to separate vapors of raw materials, which preserves the taste of the source material.

In classical packing columns, the tap-changer type (regular Panchenko packing) is mainly used. There are options with the use of nozzles of the SPN type (spiral - prismatic attachment). These nozzles are wire windings. The wire can be stainless steel, copper or another metal.

A continuous mash column can be attributed to mash only conditionally. In fact, this is the same dish. Only mash is served from the fermentation tank with a pump.

BC industrial production

Today on sale there are many options for moonshine stills. One of them is the beer column "Rectifay". This is a compact distiller that strengthens the mash. With its help, a distillate is obtained with the aroma of the raw material itself. The required strength is obtained by adjusting the supply valve cold water. The column itself consists of a dephlegmator, an on-load tap changer and a cooler. Rectify works in two modes. Like a simple moonshine still and as a rectifier. The set consists of a digital thermometer, the mash column itself, a reflux faucet and a silicone hose.

In addition to the moonshine still described, there are other brands on sale, such as the Malyutka beer column, BK (brew column) Buran, Bogatyr BK and others. The simplest is the baby column.

Preparation for the design of moonshine

First you need to draw a drawing or a simple circuit future product. There must be a place for a thermometer. The wash column or a good moonshine should be of a certain height. This height should be about fifty centimeters. Each moonshiner himself determines the strength of the future product. But in any case, experts It is recommended to make the device not less than thirty centimeters high.

It is necessary to determine the number of dephlegmators. Experts recommend mounting three such elements. A mandatory element of moonshine stills is a condenser - cooler. It is responsible for cooling and condensing the steam rising from the tank. To regulate the cooling of the dephlegmator, a source of running water is needed. It should be noted that the coolant must be supplied to each dephlegmator and refrigerators separately. Flexible tubes for supplying and draining water, as well as the condensed finished product, should only be silicone.

Each master can contribute its know-how. The main condition here is that all design improvements should affect the quality of the product, not vice versa.

Manufacture of a column with a reflux condenser equipped with a "jacket"

The continuous mash column is made with a jacketed reflux condenser. This will require four copper tubes. Their length should be 20 centimeters, 10 centimeters, 5 centimeters and 3 centimeters. They will fit the diameter of the tube from the brake system of the native Zhiguli. You will need five two-raster adapter sleeves. But, depending on the inventor's decision, more may be required. Five pieces is the smallest number. Requires female adapters.

To begin with, a spiral is made with a release for withdrawal from the body of the apparatus. An aluminum wire must be wound on the resulting spiral to increase the efficiency of the coil.

Then the cover of the device is made. An ordinary polyethylene lid for jars will do. Only with a brass sleeve fused into it and a tightened nut.

The manufacturer of the moonshine still chooses the method of heating the "cube" independently. Heat raw material can be on gas or electric stove. Some moonshiners prefer the container with raw materials to have autonomous heating. To do this, the heating element is mounted in the tank itself. . Fits a regular electric kettle. The built-in boiler should not reach the bottom of the "cube". The hole for the boiler cord must be well sealed.

Deviation options

When assembling a mash column with your own hands, it is not always possible to adhere to the basic requirements for their manufacture. It happens that it is not possible to mount controlled dephlegmators. There are also industrial options in which the dephlegmator is uncontrollable. These are the “Baby” mash columns. In this case, handling has become a victim of compactness. In it, a dephlegmator and a condenser are mounted together in one cylinder and are cooled by running water from a common water main. Such a column does not provide a high strength product. Fifty degrees maximum.

For most moonshiners, the best beer column is Rectifay. To make the device with your own hands, many recommend simply copying this design and using stainless steel materials. For all threaded connections put gaskets from the clamp. Clamp is a connecting piece that is used only in dairy, food, pharmaceutical and chemical industries . Connections are reliable and tight.

Conclusion

Strong drink lover own production he decides which device to use: buy industrial production or own assembly. But it may also be that a neighbor in a garage cooperative is constructing a moonshine that is in no way inferior to an industrial one, but much cheaper in price. And he can make it in any configuration required by the customer.