How and with what to seal rubber boots? How to seal rubber boots.

Instructions

Cut out an outsole from thin microporous rubber.

Take rubber glue, glue “88” and mix both compositions in a 4:1 ratio. Apply the resulting mixture in a thin layer with an old toothbrush. sole boot and outsole. Try not to let the glue clump. The applied glue should dry for 5 minutes.

Now again spread the prepared mixture onto the leather sole. Dry the glue again for a few minutes and firmly connect the surfaces to be glued. Leave the item being repaired under the load for one day. Now trim the protruding edges of the outsole with a sharp knife. Your updated one is ready to serve you further.

Video on the topic

Sources:

• How to repair shoes

It often happens that the shoes still look quite good, but the soles have peeled off a little. What to do - run to the master shoemakers or try to eliminate the trouble on your own? Fortunately, today there are a lot of high-quality adhesives on sale. So if the sole has peeled off just a little, try fixing the boot yourself.

You will need

• - special glue 88;
• - ordinary rubber glue;
• - rasp or sandpaper;
• - a piece of cotton fabric;
• - iron;
• - rubber glue;
• - nylon;
• - soldering iron.

Instructions

Take special glue 88 and regular rubber glue. Mix one part of glue 88 and four parts of rubber and grind thoroughly so that there are no lumps left.

Next, take the boot and start cleaning sole. For this painstaking work, use a rasp or coarse sandpaper. Clean up sole you need to be very careful so that no dirt remains on it.

Spread both parts, that is sole and the boot with a mixture of glue, fold it well and then press the boot down with pressure, first making sure that the glue and the boot are as even and neat as possible. It is advisable to let the boot dry for about a day. After that it is already possible.

It happens that the sole falls off the shoe completely. Then it and the shoe need to be thoroughly cleaned in the same way, using a mixture of glue. Next, the glue is applied to sole. Leave it for about five minutes. After that, apply a second ball of glue, wait another minute and stick sole to the shoe, make sure it comes out neatly. After gluing, put it under pressure and wait about a day.

Another method of gluing soles can be used to glue a new sole to an old sole as a “prevention”. To do this, take an improvised adapter - a piece of cotton fabric. It needs to be welded to the old sole using an iron. Stick a rubber band on this adapter sole. For gluing, use the most common rubber glue.

If the sole has come off at -, then it can also be successfully glued. For this you need to clean it very well. Next, place a strip of nylon along the perimeter of the sole and a new one on top of it sole, then use a heated soldering iron to melt the nylon. After this, press firmly sole.

note

Remember that such home repairs are suitable for boots and shoes if you are not afraid of the consequences of the experiment. If the shoes are too valuable for you, then you should contact a professional master.

Shoe repair is a responsible and serious matter. This is why many people prefer to have it done by a professional shoemaker. But there are also times when you have to repair shoes yourself. How can I fix it? sole?

Instructions

First of all, prepare the thread for stitching the sole. To do this, take a very ordinary thread and simply treat it with tar or wax. Thanks to this, the thread will become water-repellent and will not unwind into individual fibers due to mechanical stress. Then take the shoe. Now step back at least 5 mm from the edge of the grant and draw a stitching line in a circle with a pencil.

Take an awl that has a hook at the end. Pierce it along the intended line sole. Make small stitches with an interval of no more than 10 mm. Try to tighten each stitch as much as possible so that the thread in no case gives any slack and certainly does not form loops. The stitches must be made in such a way that the thread is not visible from the outside. In addition, it is recommended to make a small indentation along the seam line. But don’t spoil it by making such a channel. Better practice first.

There is another option for fixing the sole. However, it will require you to have skills in working with glue. Lightly strip sole coarse-grained sandpaper or a rasp. Take two types of glue: rubber and “88” glue. Now they need to be mixed with each other in a 4:1 ratio. Apply a thin layer of the mixture to the outsole and sole shoe with an old toothbrush. Try to carry out the entire procedure so that the glue does not form clots. Give the applied glue 5 minutes to dry.

Re-treat the leather with the prepared mixture. sole. Dry the glue again for a few minutes, and then firmly and forcefully connect the surfaces to be glued. Leave the shoes being repaired under a load for the whole day. Then trim the protruding edges of the outsole with a sharp knife. That's all the repairs. Your updated shoes will serve you for a long time.

If the soles of your favorite shoes or boots have become unglued, you can fix them yourself. Having at hand necessary materials, it’s not at all difficult to do. The main thing is to follow the instructions exactly. Then the shoes will serve you for another season.

You will need

• - pure gasoline;
• - glue 88N;
• - needle file;
• - soldering iron;
• - dratva;
• - awl;
• - shoe hook;
• - prevention.

Instructions

Before you begin repairs, determine what the sole is made of. Usually it is rubber or made of . If the sole is rubber, clean it of dirt and thoroughly degrease it using a clean one. After that, apply 88H glue on it and wait until it dries. This usually takes 10-15 minutes. Stuff your shoes with newspaper or any thick paper. Place it under the press for 8-10 hours.

If the sole is made of polyurethane, clean the bonding area from dirt and degrease with clean gasoline. Take a flat file and carefully file away the colored layer of leather. Degrease the surface to be repaired again. Using a heated soldering iron, spread small pieces of polyurethane (cut from the sole) over the skin in the area that needs. Squeeze sole and the upper part at the gluing site and pass a soldering iron between them. Keep in mind that this type of sole requires some training. Accurately maintain the pressure between the sole and the upper of the shoe and monitor the temperature of the soldering iron. The device must be very hot.

If the peeled sole has an edge that extends onto the shoe, it can be repaired in another way. Clean the damaged area from contamination and degrease with clean gasoline. Apply to sole and apply 88N glue to the upper skin in place. After 10-15 minutes, press as hard as you can sole to the top. Take dratva (strong twisted linen thread), rubbed with shoe polish. Using an awl and a special shoe hook, sew sole to the top of the shoe. Remember that the seam should be at a distance of 4-5mm from the top edge of the sole.

If small cracks appear and it begins to peel off, you will need 88H glue and rolling (prevention). Clean the damaged area and degrease with clean gasoline. Apply glue to sole and for prevention. After 15 minutes, stick the roll on sole and place under a press for 8-10 hours.

Often, with active and constant use of shoes, they very quickly become unsightly: the seams begin to come apart, the sole becomes deformed or comes off. In this case, it will take a little time to get the boots in proper shape. With everything you need on hand, you can quickly seal your shoes yourself. Thanks to this, it will serve you for more than one season.

You will need

• - Sandpaper,
• - “Moment” glue,
• - acetone or gasoline,
• - a rag.

Instructions

Before we start repairs shoe, we need to prepare them properly for this. To do this, wash your shoes thoroughly with a brush and soap, rinse clean water and leave to dry naturally at room temperature for at least one day. If the shoes do not dry enough, then it will be very difficult to glue the materials to each other, since the moisture will continue to evaporate. In this case, there is a possibility that they will break the next day.

Take a small piece of material or a regular cotton pad and soak it in acetone. Treat both surfaces to be glued properly, this way you will not only remove any remaining dirt, but also degrease the surface of the shoe. If the gap in the boot is large enough, in this case it is recommended to clean the surface of the material using fine-grain sandpaper. Thanks to this, they will stick together much better and stronger. For degreasing, you can use regular gasoline.

Apply enough good layer Apply suitable shoe glue to the gluing area and leave to dry for 10 minutes. After this, carefully connect shoe s and press firmly, hold for a while so that the surfaces can fix and remove excess glue. After that it remains to put shoe under a press for a day, this could be a chair leg or another object. For gluing shoes, Moment glue is best suited, which is sold in large tubes and has yellow. You should not use super glue, it will not give the desired result.

If shoe unstuck again, then there is a better way that will really help maintain the shape of the shoe - stitch it. In this case, it is advisable to contact a specialist - a shoemaker. If you decide to sew them up yourself, in this case you will need fairly strong threads and a thick shoe needle, as well as a lot of strength and patience.

Video on the topic

Helpful advice

Before going outside, especially in wet and slushy weather, be sure to treat your shoes with special impregnations and wax, which can be bought at almost any shoe store or market. This will help keep your shoes in good condition and your feet dry.

Unfortunately, shoe soles sometimes crack. As a rule, patches installed on a crack do not give the desired result - the shoes continue to get wet, and the “patch” quickly falls off. How to repair a burst sole?

You will need

• - acetone or gasoline;
• - sandpaper
• - bicycle camera;
• - rubber glue;
• - shoe knife;
• - soldering iron;
• - nylon.

Instructions

Cut the edges of the sole around the crack to a width of 5-7 mm using a shoe knife. The cutting depth should be one millimeter.

Carefully measure the depth of the crack in millimeters. Add 15 mm to this value. Take an old bicycle inner tube and cut a strip out of it, the width of which will correspond to the result obtained.

Sand the strip using sandpaper. Degrease using acetone. Coat the strip with rubber glue on both sides. In this case, on one side the glue must cover the entire surface completely, and on the other side it is necessary to leave dry edges. The width of these edges should be 5-7 mm.

And the question arises, ?

But after using the method of gluing with rubber glue, many people get upset because for some reason the patch falls off.

It’s strange that the glue is rubber, but it doesn’t stick to rubber?

Yes, it really doesn’t hold, and even if it does, it doesn’t last long.

Then we try another method, take it to a shoe repair shop. And there they say: “We don’t glue rubber shoes.”

It’s strange again, a shoe workshop, but they don’t take shoes for repairs.

And it’s true that shoemakers rarely undertake tire repairs. new shoes. The only thing they can advise is to go to a car repair shop where car tires are vulcanized.

But, most likely, they will refuse you there, saying that this rubber cannot be vulcanized, or they will even say that they no longer have such a service, since now many drivers have switched to new types of tires where vulcanization is not used.

What to throw away? But I really need them.

Don't worry, there is a way out!

I offer you one of the most effective and proven methods, namely, how to glue a patch to rubber shoes.

Although it won’t add any beauty, the patch will stick.

At the moment, quickly and reliably patch rubber boots maybe a miracle invention that cyclists have been using lately.

It's called a camera repair kit.

It's not expensive but it sticks perfectly. Of course, I can’t guarantee 100% that it wakes you up exactly as you want, but I tried it, it works.

It includes ready-made patches, by the way different sizes, glue and even sandpaper (may not be available everywhere).
It is very easy to glue them. Instructions are always included with it.

I’ll add from myself:

• Mark the place where it is necessary to patch, applying the patch accordingly required size
• Clean it well emery cloth(some people advise degreasing with gasoline, but I would not recommend doing this at all if the shoes are clean and not greasy, and if degreasing, then only with acetone)
• Apply glue to the selected area on the boot
• Remove the protective film from the patch and smear that side with glue (someone may have a question about which side to apply on the patch - I repeat the one under the film, but after gluing, a colored rim on the patch will be visible)
• Let the glue dry for about 10 minutes and press.

Of course, you shouldn’t wear it right away, wait a while, and it’s better to wear it the next day.

If a hole appears on the sole, then of course a different approach is needed.

First, this place must be processed on a sharpening machine so that the surface becomes perfectly smooth, otherwise everything will be useless. And then we glue it as usual.

But keep in mind that this patch will quickly wear out if you walk in it, say, on asphalt. That is, it is designed to go into the water, but not for long walks.

But in principle, if it wears out, you can do the previous procedure again.

So, it's possible quickly and reliably!

But as you noticed, we were talking about simple rubber shoes, which are intended for ordinary household chores.

Tape up rubber boots It can be very difficult at home. This can be confirmed by everyone who has ever tried to do this. The fact is that ordinary glue, which we use to glue ordinary shoes, is not suitable for rubber boots. At the same time, it doesn’t matter Do you want to seal the seam, sole or any other part of the boot?. Of course, the easiest thing would be to simply take the shoes to be repaired, paying a tidy sum, but here we also face a problem: not all shoe shops undertake to glue rubber boots, because they themselves do not know how to do it. Here we can only rely on ourselves and glue the boots ourselves, or mercilessly throw them in a landfill. But before you sigh sadly as you try to stuff your rubber boots into a trash bag, let's try to seal them up on our own.

To effectively seal rubber boots, we need to know where the damage is. Rubber is a material that is very easy to pierce with a sharp object. You can simply step on glass or a sharp brick to create a through hole in the sole. This is a very unpleasant phenomenon, as water will quickly accumulate in the shoes. But if we find damage, we can repair it at home. For this we need:

special glue for rubber;

bicycle glue;

car glue.

You can find rubber adhesive in fishing stores, but before that you should make sure that the boots are really made only of rubber. Otherwise, the glue may not be suitable.

The adhesive used by cyclists is usually sold either in stationery stores, or in specialized places where you can find parts for bicycles.

You can find car glue in stores. car parts, surprisingly. It is best to ask the sellers what product would be better suited for sealing rubber boots.

And there are several methods by which this can be done. Let's take a closer look at how to seal rubber boots.

To seal rubber boots with bicycle glue, you need to carefully read the instructions, which you can find on the tube. After this, you need to degrease the area that you are going to seal using acetone. Then take a small piece of fine-grit sandpaper, run it over the surface a few times, and then you can start sealing. To do this, you need to smear the part of the boot that you are going to glue, and then take out one rubber patch from the pack that comes with the glue. Peel off the film, apply glue to the sticky side of the patch, and then apply it to the rubber boot. Wait about five minutes for the glue to dry a little, then press the patch firmly. It must be held in this position for several minutes, after which send the boots to a warm place to dry.
The only disadvantage of this method is that after gluing the boots do not look very presentable. This option is only suitable for old shoes that are not used for going out in public.

You can glue rubber boots using special glue for rubber in the same way as using glue for cyclists. Only in this case you you will have to cut the patch yourself. Old boots, inner tubes from an old bicycle, or any other rubber products are suitable for this.

You can seal smart rubber boots, on which the patch will look unacceptable, using car glue. It gets into even the deepest cracks and hardens there, blocking moisture from getting inside your boots. To do this, you should first wash your rubber boots thoroughly, dry them thoroughly, and then degrease the surface with acetone. Next, you can apply glue: this must be done in a thin layer so as not to disturb the shape of the boots. The boots can be worn immediately after you have glued them and the glue has dried.

The most practical shoes, which are specifically designed to protect feet in rainy weather, are rubber boots. But they may also need repairs, just like any other shoe. Usually the rubber diverges at the junction of the main part with the sole, grinds off, punctures, or bursts. To avoid spending money on a new pair and save on the services of a shoemaker, you can try sealing your rubber boots yourself. Thanks to this, they will serve you for many more seasons.

To repair your rubber boots at home, you will still need to spend a little money on Consumables, some of which you probably already have at home and will come in handy in the future. But in any case, the costs will not be as significant as if you had to turn to a shoe repair specialist for help. So, you will need to have on hand:

• rubber patch;
  
• rubber glue;
  
• a block and a regular hammer (may not be required);
  
• a little solvent;
  
• a piece of rags or ordinary cotton wool;
  
• file;
  
• sandpaper.
  

Instructions for repairing rubber boots at home

1. First of all, you need to prepare your rubber boots for the sizing process. Therefore, first wash them outside and inside with soap and a brush to remove dirt, then dry. Prepare a rubber patch. If you can’t find an original one cut from an old boot, you can use a bicycle inner tube.
   
2. Use a file along the back of your patch, as well as the seam around the puncture, to roughen the surface for better adhesion. Sand these areas similarly with coarse sandpaper.
   
3. Soak a rag or cotton wool in solvent and work on the patch and tear area on the rubber boot. If there are particles of rags or cotton wool left on the surface, they should be removed.
   
4. Trim the edges of the patch so that it does not completely cover the treated rough surface. Now you can begin the main stage of repairing your rubber boots.
   
5. For gluing the patch, a special glue is suitable that can reliably fasten rubber surfaces (for example, “Rubber” or “Super Moment” for rubber). You can contact a shoe repair specialist and ask him to pour special glue into your container for a small fee.
   
6. If you are using store-bought glue, read the instructions and follow all directions for use to get maximum results. Spread a thin layer of glue on the patch and the treated area of ​​the boot, leave for 10-20 minutes (see instructions for time).
   
7. Place the patch coated with glue on the area of ​​the boot and press firmly. For greater reliability, the boots are put on a last and tapped with a hammer. At the same time, you need to make sure that she does not move. The time for gluing the patch is at least 24 hours.
   

By following these simple instructions, you can always repair your rubber boots. Rubber boots are footwear necessary not only for the country house, but also for the city. They protect from bad weather and dirt. But they have one drawback - any nail or piece of glass is enough to render the shoes unusable. Of course, the easiest thing would be to simply take the shoes to be repaired, paying a tidy sum, but here we also face a problem: not all shoe shops undertake to glue rubber boots, because they themselves do not know how to do it.

Sealing rubber boots at home can be very difficult. This can be confirmed by everyone who has ever tried to do this. The fact is that ordinary glue, which we use to glue ordinary shoes, is not suitable for rubber boots. It doesn’t matter whether you want to seal the seam, the sole, or any other part of the boot.

To effectively seal rubber boots, you need to know where the damage is. Rubber is a material that is very easy to pierce with a sharp object. You can simply step on glass or a sharp brick to create a through hole in the sole. This is a very unpleasant phenomenon, as water will quickly accumulate in the shoes. But if we find damage, we can repair it at home.

And there are several methods by which this can be done. Let's take a closer look at how to seal rubber boots.

Tips before gluing boots

In order for the repair to be successful and the boots to last for a very long time, you need to know the following:

Before repairing, rubber shoes must be very thoroughly cleaned, washed and dried.
- The patch can be cut from a tire or old rubber boots.
- It is better to carefully treat the patch from the reverse side with sandpaper or a file to make the surface rough for better adhesion of the glue.
- It is best to degrease the surface of shoes with acetone or solvent.
- You need to choose a special glue, which must indicate, for example, “shoe” or “rubber”.
- Before repairing rubber boots, be sure to read the instructions from the glue manufacturer in order to do everything correctly.
- It is best to coat the patch and the gluing area with special glue several times, after waiting until the first layer dries a little.
- When gluing the surfaces, you need to press them very hard against each other or tap the gluing area with a hammer.
- The patch on the boot can be easily masked using sandpaper.

4 ways to seal rubber boots

Method 1. You can tape your boots special glue. It can be purchased in stores for hunters and fishermen. But in order to purchase the right glue, you need to know what exactly the shoes are made of. The fact is that shoes made of EVA or polyurethane require different adhesive compounds.

The seller can help you purchase the necessary glue by giving advice. Then everything is simple - you need to sand and degrease part of the boot and stick on a patch. If the shoes are made of porous material, then they can be glued without using a patch. The edges at the cut site just need to be turned out, generously coated with glue and pressed together.

Method 2. For this method you will need the usual bicycle repair kit. It contains patches on special protective films, sandpaper and, of course, glue. Clean the desired area on the shoe with sandpaper and thoroughly degrease. Next, after first removing the film from the patch, you need to apply glue to it and press the patch to the hole. You can use the shoes almost immediately, but it is better to wait at least 12 hours.

The only drawback of this method is the unaesthetic appearance of the shoes after repair. If the hole appears not on the boot, but on the sole, the gluing technology does not change. You just need to make the surface smooth and even, because usually the sole on such shoes is quite textured. This is possible using sharpening machine. And only then glue the patch to this place.

But it is important to know that such a patch will not last long, especially if the sole of the boots comes into contact with a rough and hard surface very often. Therefore, it is better to wear such boots, for example, when fishing. Well, if the sole breaks again, the gluing procedure will need to be repeated.

Method 3. In order to seal women's boots without using patches, you must purchase adhesive sealant. This can be done at any car enthusiast store. First you need to degrease the gluing area, and then lubricate the torn edges with glue and press them together. If you do everything carefully, the boots will look like new.

Method 4. This method of repairing rubber shoes is also called "hot" method. It is not complicated, but it requires certain skills and, most importantly, a vulcanizer. Rubber pre-soaked in gasoline is used as a patch. It is placed on the hole in the boot and clamped with a vulcanizer. The device needs to be turned on for 20-30 minutes, then turned off and cooled. Only after it has cooled can you remove the press.

Don't despair if your favorite rubber boots suddenly break. It is enough to put in a little effort and the repaired boots will be no different from new shoes. You can use taped boots a day after the patch was applied. But if you don’t have time to wait, then you can wear them in an hour.

How to care for boots

Rubber shoes must be properly cared for. And then you won’t have to resort to them frequent repairs. After all, even the high quality guaranteed by the manufacturer does not always mean the safety of the shoes.

Rubber boots need to be cleaned properly. They are best washed with a solution of glycerin and water. In this case, boots should be wiped with a soft cloth and dried often to prevent fungus from appearing.

Wet rubber boots cannot be dried with a hair dryer or radiator. It is necessary that the shoes dry naturally.