Submersible centrifugal pump for a well water cannon. Water jet pump: description and specifications

The pump "Vodomet" for a well is a multi-stage equipment with floating impellers washed by water. Water cooling is one of the important factors which prolongs the life of the device.

Description

The design includes a built-in condenser, which is necessary for supplying water from the well. Its inner diameter can be equal to 100 millimeters or more. It is noteworthy that such a device is suitable for working in wells that contain an increased amount of sand. These pumps can be used with control by the level of filling the tank or by the level of liquid pumped out of the system. automatic control by pressure. Not only a well, but also an open reservoir, as well as a well can act as a source of water supply.

Feedback on the choice of model

If you decide to purchase a Vodomet pump for a well, you should be aware of the criteria by which this equipment is selected. According to users, it is important to pay attention to the numerical designation, the first digit indicates the maximum one minute output in the absence of flow resistance. Looking at the second number, you can understand what is the maximum head in meters developed by the equipment when working "to a dead end".

If you have a pump of the Vodomet 60/52 brand in front of you, then, according to buyers, this indicates that with a free spout, the equipment is capable of supplying 60 liters of water per minute. This volume is equivalent to 3.6 cubic meters per hour, while when the supply is cut off, the pressure will be 52 meters, that is, 5.2 atmospheres. This unit is almost never used in the limit mode, most often it is operated at the operating point.

The pump "Vodomet" for a well with a maximum flow rate of 115 liters per minute is used for wells and wells with an increased and average flow rate. If there is a need to select equipment for water sources with a high flow rate, then you should purchase an option with a maximum flow rate of 150 liters.

General characteristics of submersible type devices

The submersible pump "Vodomet" for the well has a high coefficient useful action he is ready to serve long time. This equipment has a powerful electric motor cooling system. The design of the pump has a cable that can be pulled through the top cover, which allows the equipment to be used in wells of even the smallest diameter

It is noteworthy that these submersible pumps can operate continuously for a long time, this became possible due to the presence of a built-in water "jacket". It provides water passage between the motor stator and the housing. "Water cannon" is capable of supplying liquid from shallow or great depths. The devices have good tightness and are equipped with a thermal protector, which is responsible for the temperature of the equipment.

Characteristics of the pump brand "Vodomet prof 60/32"

If you are interested in the products of the brand "Vodomet", the pump for the well "Prof 60/32" can be purchased by you. It belongs to the high performance series. Such equipment is suitable for water with a significant sand content. It can only be used in those wells whose depth does not exceed 30 meters. The temperature of the liquid should not be more than 35 degrees.

Consumers who decide to purchase this equipment should be interested in the power of the submersible pump, which is 470 watts. In one minute, it will be able to produce 60 liters of liquid, the maximum amount of pumped sand will be equal to 2 kilograms per cubic meter of water. The products of the brand "Vodomet" have long become popular with Russian consumers, the pump for the well "Prof 60/32" is a confirmation of this. Its body is made of high quality stainless steel, which ensures a long service life of the device. However, in the process of using the unit, you must remember that the pressure should not be higher than 3.2 bar.

Characteristics of the pump brand "Prof 55/50"

When you visit the store, you can find large assortment goods that are manufactured under the brand "Vodomet". The 55/50 well pump can be considered as an example. The depth of its immersion is 30 meters, the power is 680 watts. The equipment must be installed vertically. As practice shows, the engine runs silently, and it is capable of pumping out 3.3 cubic meters per hour. Do not use this equipment for dirty water, otherwise it may be damaged. The size of the particles to be filtered can be up to 1.5 mm and the length of the power cord is equivalent to 20 meters. This information will help you when installing the device.

Characteristics of the pump brand "Dzhileks Vodomet 115/115"

If you are interested in the Vodomet brand, you can purchase a pump for a well 115/115 for 14,300 rubles. This submersible equipment is designed to pump water from a well, while the liquid may be slightly contaminated. The maximum depth, as in the above case, is 30 meters. Productivity is 6900 liters per hour. The advantage is that the device can also be used for small wells. With it, you can water the garden or garden, among other things, it is suitable for water supply in homes. The weight of the unit is 22.6 kilograms, which makes it easy to install.

This pump "Dzhileks" for a well, the photo of which is presented in the article, has a fairly wide area of ​​​​use. It can be used in tanks, as well as open reservoirs. The equipment is perfectly adapted to difficult Russian conditions. To create it, the manufacturer uses durable and wear-resistant materials. For example, granite and ceramics are selected for. With regard to such important element, as impellers, a wear-resistant polymer is used for them.

The range of products manufactured by GILEX includes several models of borehole pumps with different technical characteristics. This equipment is intended for use as part of domestic and industrial water supply systems with water intake from wells and boreholes. According to users, well pumps from JILEKS LLC are among the best on the Russian market.

Rules for choosing pumping equipment

Efficiency autonomous system water supply with forced water supply depends on the compliance of the technical characteristics of the pumping unit used with the conditions of water use. To do this, it is necessary to make a thorough analysis of all the nuances of the upcoming operation even before ordering the equipment. If you are faced with the question of which well pump is better to choose, consider the following criteria:

• well flow rate and volume of water consumption, the maximum number of inclusions per hour;
• temperature of the pumped liquid;
• parameters of the existing electrical network;
• water quality, presence and size of mechanical impurities;
• possible immersion depth for the submersible unit.

One of the most popular borehole pumps of the JILEKS company is the VODOMET centrifugal submersible unit. This equipment is available in several modifications, which allows you to choose a device with optimal technical characteristics for specific conditions of use. Each model is distinguished by high reliability, unpretentiousness, efficiency, and has a high efficiency. When choosing, use the online consultation of our company's specialists. Channels for communication are given in the "Contacts" section.

Borehole pump "Vodomet" of the company "Dzhileks" proved to be the most adapted in comparison with similar units foreign production. This is not surprising. Any mechanism is designed to work in certain conditions. The same is true with pumps. Domestic "Vodomet" is designed to work with our water, which differs from foreign in many ways.

The line of pumps "Dzhileks"

The production of submersible borehole pumps "Vodomet" is one of the main activities of the company. As a result of painstaking work, new models of pumping units have been created.

A variety of submersible pumps "Vodomet"

They have very significant differences from similar models from other manufacturers:

• high efficiency;
• increased durability of work;
• decreased sensitivity to dirty water;
• lack of vibration;
• the presence of a "washed" electric motor.

In addition to those listed, there are a number of other differences that are characteristic only for Vodomet products. Some will be discussed a little later.

Efficiency (coefficient of performance). For "Water cannons" it is higher than for similar models. The increase was achieved due to the absence of reciprocating motion and the installation of "floating" injection wheels.

The durability of the unit is increased due to the absence of valves and pistons, which are characterized by rapid abrasion during operation.

Sensitivity to dirty water is significantly reduced due to the presence of a mesh filter and a special arrangement of through channels that have the ability to self-clean.

The absence of vibration is achieved by the presence of several impellers. All of them are balanced when the pump is assembled.

The "washed" electric motor is absolutely protected from overheating.

Interesting to know. Produced models of pumps "Vodomet" are constantly being improved. Created new system seals, eliminating the violation of the sealing of the rotating units of the unit.

Design features

The submersible pump "Vodomet" has significant differences in comparison with its foreign analogues. First of all, it is necessary to pay attention to the installation of reinforced bearings on rotating parts. This ensures their trouble-free operation in conditions of high water pollution with sand particles or sedimentary solids.

Submersible pump "Vodomet", scheme

The next not unimportant feature is the optimization of flow channels and impellers. The result is the elimination of the possibility of clogging the pump as a whole. Additionally, the self-cleaning system contributes to this.

The electric motor of the unit is located on top. This arrangement made it possible to significantly reduce the diameter of the entire case, and bring the power cord out from above. Due to this, the size of the water well has also decreased. And this is already a tangible reduction in investments for its installation.

Another feature that is unique to the "Vodomet" is "floating" impellers. Without going into technical aspects, suffice it to say that such an innovation leads to an increase in pump performance and pressure, as well as to a decrease in the electricity consumed by it.

By the way, the electric motor of the unit during its operation is cooled by water passing through a specially made annular slot inside the housing. Overheating of the engine is not terrible, the unit can be operated without turning off for a long time.

Important. The pump is released Russian manufacturer and adapted to work with our water.

Model range of pumps

For small wells equipped for country houses or cottages, the design bureau of the company has developed a number of borehole pumps of the Dzhileks series.

Water cannon pump

They are compact and at the same time have the power to lift water from a depth of several tens of meters. Most units allow you to pump out water in automatic mode. If necessary, they can work without automation.

A wide range of water pumping units will satisfy the taste of any consumer. This is evidenced by the technical characteristics of submersible pumps, presented in the table:

Main characteristics

Models that do not have an automatic mode of operation do not require a special mode of operation. They easily withstand 20 inclusions per hour. In this case, the possibility of engine overheating is completely eliminated.

The next popular group of Dzhileks submersible pump models are models capable of operating in automatic mode. These units do not require human intervention at all. They turn on independently when the water pressure in the system drops, or in the case when the water level in the tank drops more than allowed. And vice versa, they turn off at the moment of reaching the set pressure or its increase above the norm. Their characteristics do not differ from those without automatic control, although the range of models is somewhat expanded.

The principle of operation in automatic mode is the current position of the float switch or the pressure in the chamber of the pumping station.

Popular Models

To fill containers and irrigate plantings, a pumping unit of the Vodomet PROF 55-35 model is quite enough. It can be used in open water bodies with a partial depth of 10-15 cm. It is not recommended for automatic water supply.

Borehole pump "Dzhileks" "Vodomet Prof" 55-50 is one of the most popular models of the company. It supplies water to a height of 50 meters. One of the advantages is the possibility of lowering it to a depth of up to 30 m. It is absolutely silent and economical in operation. Maintenance free. Ideal for autonomous water supply system country house or cottage. A more advanced model "Vodomet" PROF 55-90 allows installation in wells up to 95 meters deep.

The downhole pump "Vodomet" PROF 40-50 has a capacity of 40 l / min, therefore it is used in wells with a low debit. Is one of the best options country house applications.

Submersible pump "Vodomet" 60-32 is an analogue of the considered model. After modernization, it is able to pump out water containing up to 2 kg of sand per 1 m³. As a result of using modern materials in rubbing parts and competent design solutions are little subject to wear. Able to lift water from a depth of 90 meters.

Other models of pumps "Vodomet" are structurally similar to those considered. They differ in technical characteristics - power, performance and others. Specific figures can be seen in the table and the “Pump Operating Instructions”. Detailed information must be given by the sales assistant when purchasing the unit.

Pump installation

The submersible pump for the well of the company "Dzhileks" is installed in the water supply system similarly to other downhole units. From the correct installation in the future will depend on the performance of the entire water supply system. Install the pump carefully, following all recommendations for its installation. The most unpleasant thing that can happen as a result of installation errors is drilling a new well and installing another pump.

To exclude the possibility of such a situation, it is necessary:

1. Perform installation pumping equipment.
2. Install check valve.
3. Make sure the pump is assembled correctly.
4. Lower the pump into the well.
5. Fasten the cable to the head.

Installation of pumping equipment. It is carried out on the surface. A cable is attached to the pump, a cable is unwound, a pipeline is connected.

Check valve. Protects the entire water supply system from water hammer. Attached either directly to the pump housing or in the pipeline.

Correct assembly. All connections are checked, the insulation of the twisted wires, the fastening of the clamps.

Lowering the pump into the well performed smoothly, without jerks. After lowering to a predetermined depth, the safety cable is securely fixed to the head.

For more information on preparing for the installation of the pump, see the video at the end of the article.

Note. Holding the pump during the descent is carried out only by the rope.

The downhole pump "Vodomet" is gaining more and more popularity in the consumer market. The high quality of the product, ease of installation and reliability in operation make it indispensable in the autonomous water supply of private houses. The multi-vector design allows the use of Dzhileks products not only in wells, but also in wells and open water bodies.

Don't forget to rate the article.

In order to ensure uninterrupted operation of water production, it is necessary to install special equipment. Pumps Dzhileks Vodomet for pumping water, you can install with your own hands near the mouth of a source of drinking or technical water.

In addition, Dzhileks Vodomet pumps for pumping water from a well can be immersed under the surface of the water table. This one is able to extract the required volumes of water from a do-it-yourself well and supply it to the house, outbuildings, greenhouses or gardens.

1 What is the design of Dzhileks Vodomet pumps?

The Gileks Water Jet pump for water extraction is presented in the form of a multi-stage unit, the principle of operation of which is based on the active use of centrifugal force. All Dzhileks Vodomet pumps for pumping water are equipped with floating wheels and a washed motor. A do-it-yourself unit can reliably supply water from:

• reservoir;
• open reservoir;
• Wells.

Due to the presence of floating wheels, the Dzhileks Vodomet pump for pumping water has enough high rates hydraulic efficiency. Reviews about such a pump, for the most part, are only positive.

The technical characteristics of the Jilex Vodomet devices are quite high, this is also evidenced by user reviews. Thanks to a number of design improvements, the Dzhileks Vodomet pump has a fairly compact axial dimensions of the body and a low weight of all rotating working elements.

The consequence of all this is a significantly reduced level of vibration of the unit during its operation. In addition, it will not be difficult to disassemble such a pump with your own hands and repair it.

The use of floating wheels in the pump contributes to the minimum number of blockages that occur due to the ingress of large particles into the system.

In addition, the electric motor of the pump is well protected against sudden overheating. The characteristics of the device allow washing the engine with a stream of water in order to cool it.

In addition, the presented pump can be installed in the well with your own hands. Repair of this unit can also be done by hand.

Feedback on the installation of the pump with your own hands and how it was repaired will help you figure out how to properly carry out the procedure for such work.

The engine is located above the pumping part of the device. Such a feature constructive solution allows you to output the power cable directly from the .

Thanks to this, the pump can be mounted in a well with a minimum working diameter, and it can be easily repaired if necessary.

It should be noted that the presented layout of the pump has proven itself well in cases where the design is used and when it is partially submerged.

The unit itself consists of two main parts - this is the engine and the pump compartment, which is located in a common housing. All other moving parts and elements of the unit are centrally fixed in the housing using a special intermediate support.

It also uses the front and back covers. The pump is designed in such a way that the floating wheels included in it can approach each other.

Due to this, there is a significant reduction in the gap between the parts of the device that are in a movable state and the fixed parts.

This solution avoids the occurrence of internal leaks and, in general, has a positive effect on increasing the efficiency of the entire system.

All presented units, depending on the types of marking, have a different number of repeating steps. All parts in the device are divided into four subspecies. This:

1. Impeller.
2. Cup.
3. The bottom of a glass.
4. Anti-friction washer.

The glasses are made in the form of cylinders made using black polyamide. Each of them is equipped with a belt that rests against the ring.

The ring is inserted into the spacer located in the body. An anti-friction washer is located between the glass and the impeller; it is designed to prevent friction of the mechanism parts.

The whole system is based on the rotation of the impellers located in the glasses. The cylinders are fixed and do not move due to the fact that they are fixed between and the cover.

1.1 Types of models

All units are divided into three main categories. These can be pumps for extracting water from a well; a special cooling jacket is supplied with such devices.

In most cases, the systems are used in the arrangement of private houses or summer cottages. Downhole type units are used to provide water supply from those wells that have a large diameter.

In addition, such pumps are used in all kinds of tanks and reservoirs. Chastotnik type systems are widely used in areas where uninterrupted water supply is required in automatic mode.

As a rule, these are cottages and summer cottages. An important advantage of such a device is the ability to provide the desired level of pressure in the entire water supply line.

The pressure level is not affected by the number of points from which water is drawn. Feedback on pumps is mostly positive.

1.2 Specifications and reviews

Here are some specific parameters of the most common models.

Water jet pump "Prof 60/32"

In this series, the overall performance of the unit has been significantly improved. It is used to extract water with a large amount of sand diluted in it.

• Well depth: 30 m;
• Power: 470W;
• Pressure inside the system: 3.2 bar.

Water jet pump "Prof 60/32" A

The presented model is capable of pumping not only from wells, but also from wells, reservoirs and reservoirs. It is actively used for watering vegetable gardens and orchards. There are restrictions on the on-off cycles of the device - no more than 20 times per hour.

• Well depth: 25-30 m;
• Maximum pumped liquid temperature: +40 °C;
• Power: 500W;
• Pressure inside the system: 3.4 bar.

Water jet pump 60/62 A

A submersible type unit that can pump water from great depths. Carries out supply from deep wells, is used for irrigation and watering.

• : 52 m;
• Maximum pumped liquid temperature: +35 °C;
• Power: 630W;
• Pressure inside the system: 3.6 bar.

Vladimir, 43 years old, Ussuriysk:

I decided to equip my own yard and took up the water supply system. On the advice of a neighbor, a submersible pump Dzhileks Vodomet was installed in the well. While everything suits, water is supplied with great pressure.

Sergey, 50 years old, Voronezh:

I live in a private house, the forces are no longer the same as to constantly turn the handle of the well and carry full buckets of water. He equipped the well with a special well pump Vodomet. Now it is not at all difficult to get water, the pump pumps perfectly. I am satisfied with the purchase, I advise everyone!

Pavel, 37 years old, Saratov:

I have been installing water supply systems and related equipment for several years. All the clients to whom I installed Gileks Vodomet units were satisfied, there are no complaints.

1.3 What models of Vodomet pumps are there? (video)

2 The most common malfunctions and their repair

One of the most common unit malfunctions that require repairs is that when the device is turned on, the pump does not pump water.

If you listen carefully, you can sometimes hear a barely noticeable buzz. Sometimes the device does not make any sounds at all and can be shocked at the moment when the user touches its case.

All these signs indicate that there was a partial abrasion of the covers located between the stages and the impellers. In order for the unit to work again, it must be completely disassembled and worn out impellers and covers must be replaced.

In addition, another cause may be a faulty capacitor. In such cases, the incorrect operation of the device is due to the ingress of water through the cable passage into the cavity of the capacitor compartment.

A faulty capacitor is subjected to mandatory replacement. In the event that when the start button is pressed, the pump does not turn on, first of all, you should make sure that there is voltage in the electrical network.

First of all, the integrity of the cable, which provides power to the unit, is checked. It happens that the control panel of the device fails.

In this case, it is almost impossible to make repairs on your own. Here you will need the help of a qualified specialist.

You should also act if protection is often triggered, which is activated in the event of a breakdown of the power cable and leakage of electricity.

If, during start-up, the device turns on, but does not pump water, check that the valve is installed correctly.

In this case, the pump must be lifted out of the well and make sure that the valve is installed properly. Sometimes it happens that an air lock forms inside the unit.

To eliminate it, it is necessary to immerse the pump to a greater than usual depth. In this case, the valve is installed at a height exceeding 1 meter.

Another reason for such a problem may be improper installation and installation of a check type valve. In this case, the pump is also removed and the check valve is reinstalled.

If, when the system is turned on, a partial supply of water is produced and its pressure constantly weakens, then, most likely, the equipment has been operated without turning off for quite a long time. The reason for the low pressure is a clogged cleaning filter.

If it is clogged, the filter is disassembled and cleaned. Otherwise, it is completely replaced.

During the intake of water, the pump in some cases gets a large number of sand. In such a situation, the unit is placed in a container with water and it is pumped.

In order to avoid such moments in the future, you need to take care of installing an additional cleaning filter. If the equipment has completely stopped pumping water, then first of all the unit should be de-energized and removed from the well in order to conduct a detailed inspection.

With such a breakdown, the cause may be a significant decrease in the water level in a well or well. It is necessary to immerse the pump to an even greater depth.

In some cases, equipment jamming occurs. Often this is observed with severe contamination of all channels. If it is not possible to eliminate the cause with your own hands, then you should contact a qualified specialist or a service center.

Vodomet pumps are submersible multi-stage devices of the Russian company Dzhileks, designed to provide autonomous water supply to houses and watering plots.

Production is located in Klimovsk, Moscow region.

Equipment Features

The equipment of this brand is a range of household appliances of various sizes and different capacities, so you can choose a model that will provide the required amount of water.

Advantages of submersible pumps:

• work quietly;
• are small in size;
• do not "trouble up" water, unlike vibration ones;
• small size;
• low price;
• high efficiency;
• reviews of submersible pumps Vodomet are mostly positive - there are practically no negative ones, which is also a significant indicator;
• the ability to work in water with a significant amount of sand or clay (from 2 to 5 kg / m 3).

Water pumps Vodomet, designed specifically for Russian operating conditions, are of two types:

• wells;
• borehole (deep).

What are their differences?

Pumps for wells Dzhileks Vodomet are designed for use in relatively shallow wells (8-10 m), tanks or open water.

A prerequisite for the operation of such a pump is the sufficient width of the reservoir so that not only the pump, but also the float switch can fit there.

The water cannon pump for the well has obvious benefits before the well:

• greater efficiency, which means, all other things being equal, the submersible water jet pump for wells will have a greater performance than the water jet pump for a well;
• less sensitivity to dirty, "sandy" water;
• the presence of a simple float switch, thanks to which there is no need to install protection against "dry" operation;
• low price - from 9,000 to 13,000 rubles.

The submersible water pump for wells is smaller in size and is designed for extracting water from narrow (from 100 mm) and deep wells, lifting water from a considerable depth (usually the depth of wells is from 40 m).

The price of pumps for water jet wells is slightly higher than the price of well pumps - from 10,000 to 24,000 rubles.

About manufacturer's models

Submersible pumps Vodomet are available in several modifications, differing in power and other technical characteristics. Pumps for wells are marked as follows: pump Vodomet 55/35A, 55/50A, 55/75A, 150/30A, 150/45A, 150/60A.

Here, the letter "A" indicates that the pump is equipped with an automatic float switch.

Well pumps have the following designations: Water jet pump 40/50, 40/75, 60/32, 55/35, 55/50, 55/75, 55/90, 110/110, 115/115.

• The first number indicates the pump's maximum outlet flow (l/min). This flow rate is determined with open taps and no resistance to water movement.
• The second number is the maximum head (m), which develops the device with fully closed taps.

For example, the submersible pump Vodomet 60/32 delivers up to 60 liters of water per minute with a free spout, and when the water consumption taps are closed, it can create a pressure of up to 32 m. This unit costs almost 6800 rubles.

Based on the technical characteristics, we can say that:

• Water jet pumps with a maximum possible flow rate of 60 l/min will work most efficiently in water supply sources with a small flow rate (the amount of water that a source can give per unit time). In this case, the flow rate of the source must be no less than the performance of the pump, otherwise the pump may pump out all the water in the well (well), and begin to draw in silt or work “dry”, which can lead to its breakdown.In real conditions, a submersible pump Vodomet 60/52 at a price of about 8000 r can provide a consumption of 35-40 l / min (more than 2 m 3 / hour) - up to 4 consumer taps at the same time. Pump submersible water cannon 60/72 at the price of 10,000 r will give a stronger pressure at the same flow rate. Thanks to this, with the help of such a pump it is possible to move water over a greater distance.
• Pumps Vodomet with the highest flow rate of 115 l / min, provide for use in wells with medium and high flow rates, with a possible water flow rate of up to 65 l / min (about 4 m 3 / h). The submersible pump Vodomet 115/115 is one of the most powerful borehole pumps in the line. Its power is about 2200 kW, and the price is 16,000 rubles.
• Pumps Vodomet with a flow rate of up to 150 l / minute are necessary for the water supply of large houses. Such pumps can only be used in wells with a high flow rate, and their use is advisable at high water flow rates - more than 4 m 3 / h.

More accurate data for selection is easy to calculate on your own. The required pressure of the pump is the sum of the values ​​of the required pressure in the taps of consumers, possible pressure losses in pipelines and the height difference between the source and consumers.

Roughly, the maximum pump head can be determined by measuring the distance from ground level to water level in a reservoir:

• if the specified distance is less than 5 meters, then a pump with a head of up to 35 m is suitable. For example, a submersible pump Vodomet 55/35;
• if the distance is from 5 to 25 m, then a device with a declared head of 40 or 50 m is suitable. For example, a submersible pump Vodomet 60/52;
• if the distance is 25 - 45 m, you should choose a model with a head of 60 or 75 m. For example, a submersible pump Vodome 60/72;
• if the distance is from 45 to 60 m, it is better to choose a device with a pressure of 90-150 m. For example, a submersible pump Vodomet 115/115.

Device Reviews

Water pumps Vodomet are very popular with owners of private houses and summer cottages, so a variety of reviews have been accumulated about pumps for Vodomet wells.

Since the submersible pump for the water jet well is not deprived of attention and there are enough reviews about it - let's give a few for an example.

Maxim Viktorovich, 41 years old, Podolsk:

I have had a submersible water pump for the fifth year. Installed in a well at a depth of 25 meters. It works and works, the pressure is normal, only sometimes there is not enough water for everyone.

At first, I thought that my sandy well would "kill" the Vodomet well pump in a couple of years. I don’t know about others, but everything suits me. I'm thinking of looking at a more powerful model.

Maria and Alexander Semenov, Kursk:

Considered different variants for supplying water to the country house. We chose between Ukrainian Aquarius and Russian Gileks. Aquarius, they say, is very sensitive to sand, a remote condenser is also inconvenient. In general, we settled on submersible pump Water cannon 60/52.

It turned out that it gives 52 l / min only in ideal conditions, but in fact it comes out two times less. Nobody warned us about this. Would have known in advance — bought more powerful.

Mikhail Viktorovich, 61 years old, Ufa:

Reliable, good device. A submersible well pump Vodomet has been installed in the well for more than three years. It extracts water from eight meters and in a straight line about 35 meters more. Disadvantages - it is bad to connect through the RCD (often knocks out) and the cables are short.

About the device

The pump, completely immersed in water, works in very difficult conditions. Despite research, testing and the latest developments, these devices often fail. The causes of breakdowns are very diverse, but the main ones are:

• installation and operation of the pump in violation of the manufacturer's recommendations;
• voltage drops;
• dirty, sandy water;
• mechanical wear of parts of the mechanism - housing, blades.

In order for the Water Jet water pump to work properly for as long as possible, it must be installed correctly. So, when installing a pump in a well, it is necessary to mount it in casing pipe from inside diameter not less than 100 mm.

The upper part of the pipe is closed with a cap to prevent foreign objects from entering the well.

To prevent the device from freezing in winter, a closing well is installed above the well, and the main pipe to the house is buried in the ground below the freezing level. The pump is installed so that it is lowered into the water, but not closer than 1.5 m to the bottom of the reservoir.

The schematic diagram of connecting the Water Jet pump is no different from the nuances of installing any other pump for a well - tied to a cable, it sinks to the bottom of the well. Attached to the cable with staples power cable and a hose through which water will flow.

After the device is at the bottom, the cable should be firmly fixed at the top.

A big plus is that do-it-yourself repair of the Water Cannon pump is quite possible. For a successful repair, you will definitely need spare parts to replace the damaged ones.

If "guilty" - circuit diagram water jet pump - the capacitor may have failed. If the water from the tap began to flow worse, the filter may be clogged or the hose is damaged (and the water simply flows back into the well).

The internal structure, the procedure for disassembling and repairing the Water Jet pumps are indicated in each instruction for the device.

However, it should be noted that it is not recommended to engage in such work on your own - despite the simplicity of the design, its disassembly and assembly (especially) requires some experience.

Equipment overview (video)