Assembling a kite. How to assemble a kite from what is available? Packing the kite, assembling

29.08.2019

(http://nepoceda.com/kak-sobrat-vozdushnogo-zmeya)

Basic elements of a snake

Frame - depending on the model, it may consist of two or more rails. The mutual arrangement of which depends on the specific model. Serves for structural rigidity during flight.

Cloths - light fabric, cellophane or paper, which is covered with a snake frame. Due to this, there is an obstacle for the wind that creates lift. The canvas is placed in relation to the wind in front of the frame.

Tail - usually made in the form of one or more ribbons, and even with bows. Serves not only as a decoration, but also to smooth out imperfections during the flight. The tail is not found in all models.

Bridle - for attaching a thread (leera) to a kite. They are of several types, depending on the number of attachment points:

with one - does not require adjustment, the tail does all the work

with two or more - there is usually a regulating part (ring) here to adjust the angle of attack by the wind.

with a keel - a single piece connected to the canvas of the same material, instead of a bridle with two fasteners. Does not require adjustment, usually a tail is hung for this purpose

Leer (thread, rope) - with its help they control the flight. It should be light and strong, preferably with the ability to unhook from the snake. For this purpose, they put carbines for the tail, by the way, too.

Coil - for winding thread (handle). Facilitates use and less risk of tangling the rope.

Consider the possible options:

1. If you have a rail (twig) and a bridle, a reel, a tail in the kit.

Take the frame of the snake, insert the bridle from the front side into the holes on the snake. (for an example, see the picture above) - Turn the kite over and thread the rail into the holes (loops) at the ends of the bridle. - Next, find the special slots for the slats on the kite. They (grooves for the rail) should be located along the edges either top-bottom or left-right. I draw your attention to the fact that the rail should be on the reverse side of the snake, i. behind the canvas during the flight. - Turning towards you front side kite and tie a thread to the bridle. - If there is also a tail, find a hole at the bottom of the snake and fix the tail.

2. If there is no rail, but there is a bridle, a spool of thread, a tail is not a mandatory attribute. - Then just look for holes on the snake and fix it (bridle). - Next, attach the thread to the bridle. The fastener of the thread to the bridle should be on the front side. - We fasten the tail, if it comes separately. It may not exist at all.

3. Perhaps in the kit there will be only one spool of thread without a bridle but with a rail and a tail. Your model with a keel is a one-piece piece connected to the main web of the snake. - The keel should have a hole for tying a thread, or some other device - a carabiner, etc. For clarity, consider an example. in our case, it is necessary to thread the thread into the hole on the keel. We fix the thread by tying a knot. - On the reverse side, turning the kite over, insert the rail. As described above, the rail is inserted into the special. recesses along the edges of the snake (bottom-top, right-left, or, if two slats, both). - Such models are also equipped with a tail, which also comes separately, attach it, there should be holes for attaching the tail from below. in our case, it is a metal hook with a loop.

4. For models with two rails or more, the assembly principle is similar. Depending on the number of additional rails included. They are inserted into recesses on the snake. Location may vary. How to be perpendicular to each other, intersect, be parallel.

Who didn't fly a kite as a child! For many of us, this was a favorite fun, which was not difficult to make with our own hands. We made the simplest paper kites and rejoiced at how our creations flew into the wind. Now in stores you can find the most different models kites, from small children's kites to huge professional ones. And now we, having already become parents ourselves, go with interest to the sports department to buy this bright toy for our children. Let's remember together how to assemble a kite, and in what ways it can be raised into the sky.

Assembling a kite

Regardless of the level of complexity, all kites consist of a standard set of components. The most important thing in any kite is a strong frame that holds the shape of the structure during flight. It can be made from two or more rails. A fabric made of lightweight material is stretched over the frame, which creates an obstacle to the wind and allows the kite to soar in the air. It is important to know that when launching the kite, you need to position it in such a way that the canvas is in front of the frame, and the wind hits it. In some models of kites, a tail is attached to the canvas, made in the form of beautiful ribbons, which is designed to smooth out gusts of wind and stabilize the kite in the air.

The kite is controlled from the ground with a rope or thread, which is also called a lifeline. It must be very strong, but light enough not to impede flight.

The thread is wound on a special convenient spool. Often, kite makers make lifelines on carabiners so that people can unhook them. The junction of the thread with the kite is called the bridle. Depending on the number of attachment points, this can be:

a bridle with one fastening that does not require adjustment in the air. The kite is corrected only by the tail.
a bridle with a keel, made in the form of a single piece from a canvas of the same material. Also does not require adjustment during flight
a bridle with two or more fasteners, which involves controlling a kite. To do this, it has a ring that allows you to adjust the angle of flight.

How to fly a kite

It is easy to fly a kite, the main thing is to choose a suitable place and catch the wind. To do this, we find a large open piece of land, preferably on a hill, where air currents move from bottom to top. If you are surrounded by trees and houses, it will be more difficult for the snake to rise due to uneven wind, and it will only be able to stabilize at a height of about 50 meters.

Important to remember:

Under no circumstances should a kite be launched under power lines, near highways and airports, as well as during thunder and lightning storms. Even if the place seems perfectly flat and spacious to you, and the wind in a thunderstorm is just perfect for kite flying, such games can be life-threatening.
Never fly heavy kites over people or animals. If you lose control, this whole structure with a rigid frame at high speed can fly at a person and cripple him. If you want to play with the kids on the beach by the sea, this is a lightweight paper kite that won't hurt anyone.
When launching a kite in sunny weather, use Sunglasses. If you get carried away with the game and stare at the sky, you may not notice how the bright sun will harm your eyes.
Be sure to protect your hands. Use gloves and reel. In no case do not wind the handrail around your hands. A strong gust of wind can lift the kite up, and the rapidly unwinding thread will burn your skin.

Before sending your kite into the sky, we place it facing us, stand with our backs to the wind and pull the threads. Flying a kite is largely dependent on wind speed. If the wind is strong enough, the kite can be launched directly from the hands, placing it with its nose into the wind and slowly unwinding the rope. If the wind is not very strong, you may need help. Unwind the coil 15-20 meters, pull the thread and ask someone to throw the kite up. It happens that the wind is weak near the ground, but strong enough above. This is evidenced by the swaying tops of the trees. In this case, the kite will fly only at a certain height. But in order to raise it to this height, you will have to run a little against the wind.

Watch the thread tension carefully. If the wind stops and the tension begins to loosen, wind the thread around the spool or simply pull it towards you. If the wind increases, the rope needs to be unwound a little, or, for example, you can take a few steps in the direction of the wind. When the kite begins to fall, and the situation can no longer be corrected, let go of the rope so that the impact on the ground is softer.

controlled kite

When you have the opportunity to fly a kite, it's always exciting. Only here to launch such kites you need strong wind, because in light wind, holding two coils in your hands, you will not be able to run backwards. During launch, it is desirable to have an assistant. But you can also cope on your own, although, most likely, not on the first try.

When the kite takes off, keep your hands at chest or hip level. Try to pull the right thread towards you. You will see the kite fly to the right. If you pull left hand, you can straighten it or tilt it to the left, respectively. Movements should be smooth. If you pull the threads, the kite will quickly fall. Do not unwind the thread too much. Get used to the kite's maneuvers first. And after a little training, release it higher. Do not worry if the threads twist several times, this will not affect the control in any way.

V skillful hands the kite can draw different shapes in the air, as well as perform tricks such as "eight", "dead loop" and "spiral descent". If you are not yet able to control a kite, do not worry, very soon you will master all the subtleties of flight, and your kite will soar in the air for hours to the delight of you and your children.

Kites originated in ancient China in the 2nd century AD. People have learned to design various original types of kites: simple and controllable, flat and voluminous, with and without a frame, in the form of a dragon, a wing, a heart, a parachute. Today, kites are used not only as toys for children, but also for sports competitions and other useful purposes. The article contains master classes on creating kites with your own hands.

From the package

Materials and tools:

cellophane bags - 4 pieces;
thin light sticks (reed, pine slats);
thick fishing line;
permanent marker;
Scotch;
roulette;
scissors;
Super glue.

Master Class:

Measure and cut 2 sticks for the frame, 60 and 35 centimeters long.
Step back from the edge of a long stick 15 centimeters and tape a small stick perpendicularly with tape exactly in the middle.
Wrap the ends of the sticks with tape and cut them to a depth of 1 centimeter.
Pull the fishing line through the cuts, giving the frame a diamond shape. Re-wrap the ends with tape.
Attach the frame to the package, circle it along the contour and add 1.5 centimeters for the fold. Cut the film according to the marking.
Attach the frame to the film, tuck the film and secure with tape.
To the edges of a short stick (in diagrams A and D), tie pieces of fishing line 25 centimeters long, leaving an allowance for the string. Fill the knots with superglue.
Tie a fishing line to a large stick at point B in the diagram. To do this, connect 2 side fishing lines, and holding them parallel to the smaller stick, stretch the fishing line to them from point B. Tie all 3 segments together (point O in the diagram).
To point O on the diagram, tie a snake rail.
To create a tail, cut the bag into pieces 10 centimeters long, tie them together (about 3 meters long) and tie with tape to point D on the diagram.
If desired, paint the snake with a marker.

Bird

Materials and tools:

bamboo, carbon or reed rods with a diameter of 3 mm;
plastic bag;
spool of thick thread;
Super glue;
Scotch.

Master Class:

According to the scheme, cut the film and sticks.
Fasten all the twigs according to the scheme between themselves with thick threads and pour glue for strength.
Attach the resulting frame to the film and connect them with adhesive tape.
Tie a handrail to the finished snake.

Sports

Materials and tools:

lime, bamboo or pine sticks with a diameter of 10 millimeters;
polyethylene film;
spool of strong thread;
Super glue;
Scotch;
fishing line.

Master Class:

Following the scheme, prepare pieces of film and cut the required number of sticks.
Tie the sticks together with fishing line and pour glue for strength.
Stretch a string of fishing line between the two wings of the kite.
Use adhesive tape to attach the film to the frame.
For the tail, handrail and bridle, use a thick thread.

monk serpent

Materials and tools:

sheet thick paper 20 by 20 centimeters;
thick thread with a spool;
cotton tape;
thread with a needle;
iron;
scissors.

Master Class:

According to scheme 1 in the picture, bend the sheet in the middle, connecting points B and D, and iron the fold well (diagram 2).
Without straightening the sheet, bend corner B so that the sides AC and BC are aligned.
Turn the sheet over, bend corner D, aligning sides AC and DC (diagram 3).
Bend corners with vertices B and D.
Fold sides EB and E*D together with sides AE and AE*.
Iron the folds with an iron and carefully unfold the product.
According to scheme 6, make holes on the wings at points F, F * and C (tail).
Tie a thread with a length equal to half the height of the AK (image 6 in diagram 1) through points F and F * (puts).
At point C, attach a cotton tail 2 centimeters wide and 5xAC long. To do this, you need to pass the segment through the hole, attach it to the main tail and flash it (Scheme 2).
Exactly in the middle of the fetters, tie a rail of thick thread with a spool.

Flat

Materials and tools:

willow, bamboo or reed branches;
cellophane film or thick paper;
cotton ribbon 2 centimeters wide;
thread;
joiner's glue.

Master Class:

This type of snake can be of various shapes.
Aspect ratio.
Accordingly to the selected shape and size, cut out the skin of the kite from the film.
Using glue, first attach the side sticks to the skin, and then the crossed ones. The tips of the sticks should protrude 3-4 centimeters beyond the edge of the skin.
Fasten the intersecting sticks with threads.
Leave the structure to dry.
Leaving the casing on the outside, bend side AB and fix it in this position with threads.
With the sheathing towards you at points A and B, tie a thread, the length of which, when pulled, should clearly reach the center of the sheathing at point O.
Punch 2 holes on either side of the intersecting center sticks. Pass a thread through them and firmly tie it around the sticks, leaving the length of the free edge of the thread equal to the length from point O to the middle of AB.
Tie the lower sling to the center of the upper sling, tie a handrail thread to the knot connecting them.
At points C and D, attach a cotton ribbon with threads. Sew a tail in the middle of this tape at point M (dimensions are shown in Figure 6).

3D Potter Diamond Box Kite

Materials and tools:

4 rails with a length of 1060 millimeters and a section of 10 by 10 millimeters (spars);
2 slats with a length of 990 millimeters and a cross section of 8 by 8 millimeters (spacer);
2 slats with a length of 660 millimeters and a cross section of 8 by 8 millimeters (small spacers);
fabric or thick paper;
thick threads;
scissors;
drying oil;
wood glue.

Master Class:

Kiting sail

Materials and tools:

film or thin fabric;
pine slats 75 centimeters long and 6 millimeters in diameter;
thick threads;
Scotch;
scissors;
ruler.

Master Class:

Indian rhombic

Materials and tools:

film or thin fabric;
pine lath 56 centimeters long, 2 millimeters in diameter;
pine lath 82.5 centimeters long, 2 millimeters in diameter;
2 pine slats 10 centimeters each, 2 millimeters in diameter;
strong threads 80 centimeters long;
Scotch;
fabric tape.

Master Class:

Prepare rails.
According to the scheme, cut out the skin of the kite.
Glue pieces of adhesive tape in the places shown in the figure, leaving a few centimeters of adhesive tape not glued.
Place the center rail and secure it with adhesive tape as shown in the figure.
On the wingtips, attach a piece of adhesive tape with a free non-glued edge.
Insert a long cross rail between the casing and the central rail and attach it to the central tape in the middle.
Attach the ends of the cross rail to the wings of the kite with tape.
At a distance of 15 centimeters from the tip of the wing, attach another piece of adhesive tape on both sides and secure the rail and skin.
In the tail of the snake, glue both slats 10 centimeters long with adhesive tape, as in the picture.
Using adhesive tape, attach the tail of a fabric tape 3 centimeters wide and 150 centimeters long.
Pass the bridle through the holes in the sheathing at the top and bottom point, tying the thread into 4 knots.
Determine the place on the bridle, holding on to which the kite will be parallel to the ground. In this place, make a loop and attach the handrail.

The Chinese have long believed that a kite soaring in the sky takes away all illnesses, hardships and worries. In addition, kite launching is always a spectacular and fairly simple activity. The main thing is to choose the right place and take into account some of the nuances.

What kid doesn't dream of flying a colorful kite? What could be stronger than that the delight with which children watch a toy soaring in the sky? "Daddy, let's make a snake!" - says the beloved child. And the father scratches the top of his head in concern, because assembling a kite and flying it seems to be something especially difficult. But it's not like that at all.

Theoretical minimum

Before you fly a kite, you need to familiarize yourself with the basic concepts:

A rail is a thread with which a flying toy is controlled;

The bridle is a strong thread woven together, thanks to which the kite is attached to the lifeline;

Bearing area - the size of the projection of the kite on a horizontal surface;

Bearing capacity is the lifting force of one unit of bearing area;

The center of pressure is the center of the bearing area.

How to make a toy fly?

How to make a kite so that it soars? To do this, its surface should not be flat, but should bend upwards under the pressure of the air flow. That is why, when making a kite, it is not recommended to stretch the material (paper, oilcloth, fabric) too tightly. Sometimes just fixing the corners is enough. The center of gravity must be shifted towards the tail, otherwise a long hover cannot be achieved.

The leading edge of the kite must be carefully taped or reinforced to avoid eddies. For those who do not yet know how to fly a kite, it is better to give preference to flying models that have a long tail - it gives the correct balance to the whole structure.

Another important element- this is a bridle, which should consist of two threads. But such a kite is quite difficult to manage, so it is better for beginners to use a triple bridle.

Home workshop - manufacturing steps

1. To assemble the simplest type of kite, you need to take two thin pine, bamboo or plastic slats 30 and 50 cm long. Measure 15 cm from the end of the longer slat and fasten a small slat at a right angle with strong threads. Thus, a crosspiece for a flying toy is obtained.

2. At the ends of the planks, you need to make round notches into which a thin, strong thread is pulled. You should get a quadrangular frame.

3. Then you need to take thin paper or oilcloth and fit the existing workpiece. To do this, the resulting frame is placed on a sheet of prepared material and circled with a pencil or marker, adding a small distance to the allowances for fastening.

4. The pattern is cut out, after which the frame is well smeared with glue and attached to the material. You can decorate a kite with felt-tip pens, drawing cartoon characters on it (which will please your children), or depict the slender legs of your beloved woman on it (which will please you).

5. Now you can start attaching the bridle. For this, a spool of fishing line is taken, which is attached to the left corner of the workpiece. Then it must be stretched to the nose of the snake, and from there to the right corner to determine the length of the bridle. Cut the thread and attach the tip to the right corner of the snake (it turns out a long thread from one end to the other). Now we take the spool again, fix the fishing line in the bow of the structure, measure the distance to the left corner of the kite, add another ten centimeters, cut it off and tie it to the middle of the first thread.

6. The tail of the snake can be made from a thin cord or a strong nylon thread, measuring 3.5-4 meters. The tail can be decorated with paper bows.

7. Launching a kite is impossible without a leer. To do this, a long strong thread is attached to the bridle, at the end of which you can tie a small stick for ease of control.

Flat flying structures

Such kites are the simplest and most famous. The frame is made of pine or any other light wood. Sheathing is made of film or paper. Paper does not provide structural stability, so it must be durable (mica, cigarette or rice paper). If a film is used, then it should stretch poorly, but at the same time stick well to the frame (it is best to buy acrylic).

What does a monk serpent look like?

Such a flying layout got its name due to its similarity with the hood of a monastic cassock. Such a kite is perfectly centered, so a two-lead bridle is enough to launch it. The tail is used as a balancer, it should be light and thin. The material for such a kite is better to choose dense, because under the gusts of wind it is too easily crushed and falls.

Archery flying structure

This is one of the varieties of flat kite. The frame is built from a pair of rails, which ensures lightness. In this case, the front rail gives rigidity to the entire structure, but there is a greater sensitivity to the wind. Beginners are not always able to master the first time flying this type of kite.

box design

This type of homemade snake looks pretty solid, but it is quite simple to perform. He doesn't need a tail. What's more, these snakes can lift small loads, so you can put a small digital camera in them, after turning it on for video recording or continuous shooting. In this way, you can get completely unique shots from a bird's eye view. But the box-shaped design keeps well in the air only in strong winds.

How to fly a kite: choose a place

So that nothing interferes with the flight process, you should choose open areas without any obstacles. Trees, kiosks, buildings located nearby interfere with the direct passage of air currents and create unnecessary turbulence. The sea coast with its breeze is perfect (unless, of course, you have to jump over the bodies of vacationers at the same time). It is better to stay away from highways, airfields and power lines.

How to fly a kite (instruction)

First you need to determine the direction of the wind by simply drooling on your finger. Now the kite is solemnly handed over to a friend (girlfriend, child, wife). You need to stand in front of your assistant, who should hold the kite above his head, perpendicular to the ground. The wind should blow at your back, the reel with the lifeline should be in your hands.

So how do you fly a kite? First you need to slowly move away from a friend at a distance of about 20 meters, while unwinding the leash. Having given the command: “Let go!”, sharply pull the rail towards you. With a good wind force, the kite will soar in the air itself, and all that remains is to enthusiastically watch its flight. Otherwise, you will have to run around the field a little more until the structure catches the air flow.

How to fly a kite in different wind strengths? If it flies only when the person driving it is running, then the wind is too weak. With fairly strong air currents, the flying structure soars in the air with ease, and no additional effort is required. The optimal wind speed for launching a paper layout should be 3-6 m/s.

If the tension of the thread-leash is too strong, then it should be unwound a little. If the wind subsides, then the snake is pulled to itself. To return the structure to the ground, it is necessary to gradually wind up the rail and go home with a sense of accomplishment.

I have always been fascinated by kites flying in the sky! Any flow of air can change his flight and it seems that he is about to break free.

Every summer my boy asks us to buy either a bird or a fish.)) And this year we will make a kite ourselves. We stock up on knowledge and go to practical exercises in the country or in the park!))

I have collected information from various sources and am happy to share it with you.

What we need:

2 simple, wooden sticks (preferably bamboo, if not, light slats);

- kapron thread (fishing line, 2 mm in diameter);

Scotch tape, superglue, spray glue;

A large sheet of thin paper (or cellophane);

Hacksaw, scissors, marker and paint.

What do we need to do:

1. Cut the strips to the desired length. Make a mark on each rail. At the end of the rail we make cuts of a few millimeters for deepening. They serve to pull a nylon thread through them.

2. Indicate the exact center of each of the planks and tie them with a fishing line to form a cross (90 degree angle). The horizontal rail should be at a height of approximately 2/3 of the vertical one. Remember that the exact 90 degree angle must be maintained - otherwise the balance will not be maintained.

3. Pull the nylon thread around the frame, falling into the incision made. The tension should not be strong (too much tension can bend the frame). The design of the kite frame is ready.

From above we fix it with adhesive tape so that the nylon thread (fishing line) does not jump out of the incision.

4. Then, we put the kite frame on our paper. We draw a contour with a red felt-tip pen, at a distance of about 3 cm (1.5 cm) along the line of the cord. Cut out the sketch from paper along the red lines.

5.1. Apply a few drops of glue to the ends of the slats (highlighted by a rectangle) This glue will help keep the paper on the slats in correct position. We are waiting for it to dry.
We bend the borders of the edge of the paper (3 cm) and glue it with adhesive tape, however, it is better to use spray glue because of its lightness.

BUT! From that moment on, in different sources attached differently. Below I will give other master classes, you can see.

5.2. We wrap the edges of the film inward around the fishing line and fix them with tape. The "body" of the snake is ready.

5.3.

6.1. Cut out a piece of cord 30 cm long. At the intersection of the rail, make small holes in the paper and thread the nylon thread. Fasten it securely, you can fix the knot with tape. The cord should hang freely.

O cut a very long piece of fishing line. It will be needed to release the kite. Tie one end of it to a 30 cm cord, wind the other on a spool.
Everything is ready! Now you can paint the paper in variegated colors (to your liking) and run in good weather

6.2. I've seen models where the rope that holds the snake is tied directly to the cross, but the bridle allows the kite to maintain the correct angle of attack in relation to the wind. Therefore, it is better not to be too lazy and do it.

To do this, on the edges of a short stick at points A and G (see drawing), we tie two pieces of fishing line AO and GO with a length equal to side AB (we have 25 cm) - these will be the side parts of the bridle.
Don't forget to add an allowance for tying. For reliability, we coated all the knots with superglue, because it is difficult to make a strong knot on the fishing line.
And we tie the long side of the bridle to the upper end B (see drawing). How the kite will fly depends on its length. Therefore, it is better not to firmly fix the place of attachment to the main fishing line, but experiment with the angle of inclination. In our case, it turned out that, oddly enough, the kite flew best with BO=0. Those. it was possible to do without a bridle, and tie a fishing line to the upper corner of the kite. I think this parameter is very dependent on the specific launch conditions and on the specific kite.

After that, we connect all three ends of the bridle to each other at point O and tie the handrail there. We additionally secured this place with tape.

7. Now we make the tail of the snake. It is needed not only for beauty. how much for proper balancing. It is by adjusting the length and weight of the tail (tying or untying pieces from it) that the flying qualities of a kite can be improved.

The tail of a snake can be made from rope, from ribbons and bows, but we only had plastic bags on hand. Therefore, the tail of our kite is made of them. To do this, the packages were cut into pieces. 10 cm wide.

After that, the strips of polyethylene were tied together to make a rope about 3 meters long. We attach the tail to the lower end of the kite (at point D) using adhesive tape.

A few more options:

A very easy way to make a kite:

Where and how to fly a kite?

You need to fly a kite on large open areas . If possible, it is better to launch on a hill or hill in order to use the updrafts of the wind.

IMPORTANT:

Never fly kites near power lines, wires, etc.

Never run near highways or airports.

Never fly a kite during a thunderstorm.

All this is life-threatening!

If the wind is strong enough.

A kite can easily be launched directly from the hands. Stand with your back to the wind. By pointing the kite nose up, initially holding on to the rail at the very kite. Slightly pulling the thread towards you, lift the kite up, gradually unwinding the rope.

You can fly a kite together.

Your assistant holds the kite upright with the nose up. You unwind the rope 20 meters and step back. Having given the command to the assistant to release the kite, while slightly tossing it up. Watch as your kite takes off rapidly while keeping an eye on the tension of the thread - more on that below.

If the wind is not strong enough:

Standing with your back to the wind, we put the kite on the ground perpendicular to the direction of the wind, i.e. facing towards us. Gradually unwinding the rope, we retreat, holding the kite in this position.

When you move ten meters away, pulling sharply, run a little until the kite gains the required height, feeling how the kite has caught the wind and rushes up, where it can soar with ease. Provided that at the top there is a strong enough wind for maneuvers. Otherwise, you will have to run and keep the kite in the air.

Let's start together.

The only difference is that the kite is in the hands of the helper. This option is more suitable for starting with a child. You will play the role of an assistant. Your task is to raise the kite as high as possible while holding it perpendicular to the direction of the wind, strictly nose up. After unwinding a couple of meters of the rope, ask the baby to scatter. You will have to let go in time, slightly tossing up. (For babies from 2 years old).

Older children need to be explained how to proceed, after your kite has caught the wind, you will feel resistance, you can stop and start adjusting the flight. To reach the maximum height, if at the height where it soars without any of your efforts, simply unwind the rope to the desired distance.

How to fly a kite.

- The wind has died down- the kite began to fall - pull the rope over yourself by lowering your hand down or taking a couple of steps back. Make sure that the thread is always taut.

- The wind got stronger- we unwind the rope or weaken the tension by raising our hand or taking a couple of steps towards the kite.

Your task is to periodically tighten during the moments of the fall and weaken the tension of the thread during a rapid upward jerk.

- If the flight of the kite is not stable then it soars, then it falls rapidly down, you should understand the dynamics of the movement. The kite flies where the nose of the kite is pointing.. Therefore, pulling the thread can both lift the kite and accelerate the fall. Follow the direction of the nose. At the moment of a rapid fall, slightly release the rope, allow the snake to straighten up under the influence of the wind. As soon as the nose turns up, pull the rope under the pressure of the wind, it will quickly gain height.

Another tip, if a fall is inevitable and you are unable to correct the situation, then loosen the ropes, thereby not provoking an increase in impact.

I wish you a fair wind for your kite!)))