Make a sawmill from a chainsaw with your own hands. How to make a sawmill from a chainsaw at home, drawings and photos. The main advantages of this category of instrument are

08.07.2018

The basis of each homemade device made from a chainsaw is its use as a universal drive that can be used for different devices. With their help, you can cut, pump water, remove snow, move and saw.

A sawmill from a chainsaw is a device that is used for sawing wooden products through a chain mounted on the bus. Sawing occurs due to the operation of the motor, while the engine can run on gasoline or diesel, the power indicator does not matter.

What to do next?

Always check that the chain is sufficiently tightened and lubricated with chain oil before operating the saw. We also regularly check oil and chain tension during sawing. electric saw has no starting problem, but we must always keep the power cable away from the saw chain. We start the petrol saw in accordance with the instructions supplied with the specific saw model. For a cold engine, it is usually necessary to use the choke on first start. However, if the saw does not start for 2-3 start attempts, we will make several other attempts to start without choke to avoid overloading the saw with fuel.

Today we will tell you how to create a sawmill with your own hands from a chainsaw, do you need special skills and blueprints, you will also see a video on this topic.

All the features of a chainsaw in its homemade device can be implemented using various nozzles and additional devices. The basis of any home-made device made on the basis of a chainsaw is the usual principle of power take-off of its engine, the device you need is attached to the output shaft.

After starting, the chain saw must be properly leveled, the spindle must rotate only when the throttle lever is pressed. If this is not the case, and the chain rotates even without pressing the control lever, stop work immediately and adjust the saw. The following procedure is almost identical for electric and petrol saws. Always make sure that there is no nail, screw, or any other object that could damage the chain in the material being cut at the planned cut site before starting cutting. Position the material to be cut so that it is stable and cannot move freely, at the same time, however, so that you have enough space to cut around the planned cut.

A chainsaw as a tool for creating devices with your own hands is just right, because it has the following characteristics:

powerful motor;
compactness;
relatively small weight;
autonomy;
possibility of application in any conditions.

Also of great importance is the excellent clutch design, because it is able to protect saw systems and components from possible overloads and breakdowns. Any do-it-yourself chainsaw tool is sealed, which makes it usable regardless of position.

If material needs to be cut on a rigid base, place it with a suitable piece of wood that you won't mind cutting into with the saw. Make sure untrained people or children are not within reach. The cut itself is best done at the bottom of the bar as close to the saw body as possible. This ensures the use of abutment teeth on the saw, at the same time we have more stability with the saw. If possible, we always try to avoid cutting with the tip of the casting, the top of the rod should not be used for cutting at all.

What devices can be assembled from chainsaws with your own hands?

All homemade devices based on chainsaws are divided into simple and complex.

To simple devices include the following:

pumps;
grinders;
boat motors;
bicycles and mopeds;
ice screws;
walk-behind tractors;
winches.

Among the complex mechanisms and devices that you can assemble with your own hands:

What is needed to carry out work on the home-made creation of a sawmill?

If the chain breaks at the top of the bar during cutting, the rest of the chain chain is reversed like a notched whip. If the chain breaks at the bottom of the rod on the motor, oscillation cannot occur. While working, we watch the contraction, we stop working in time for signs of fatigue. The most important and at the same time the most difficult thing is not to give the impression that we are already in control of the saw. This often results in attention span. Therefore, we must remember that chainsaws are just as dangerous as weapons that can do a lot of work in the hands of a responsible user, but the slightest inattention can have fatal consequences.

chainsaw sawmills;
snowmobiles and snowplows;
helicopters;
power plants;
snowmobile;
solid forged knives.

Any brands of chainsaws can be used at the basis of the listed devices, it all depends on the power required for the correct operation of the device that you assemble with your own hands. Most often for sawmills from chainsaws and other devices, products of the following brands are used:

Saw chain ensures independence from electricity

Strong and trustworthy, it works great in logo logs. Supplied without guide and chain. Your local distributor will be responsible for after-sales service. The small scale tree system that we have developed in many parts of the world is the backbone of many woodworking companies. The operation of this track is extremely simple. Very soon you will learn how to work on it.

On the first day, you will achieve excellent results, of which you will be satisfied. The accuracy of our trays is amazing. It allows you to make beams, boards and even millimeters of thick planks! All structural elements of the saw are anodized, which ensures high resistance to dirt, rain, snow and ice and corrosion. Through this process, you can work all year round. Its smooth surface has a low coefficient of friction, can be easily cleaned and requires minimal maintenance.

"Ural";
"Calm";
"Friendship".

Do-it-yourself chainsaw sawmill: video

You can make a sawmill with your own hands on the basis of a chainsaw without any extra effort if you have it drawing or diagram. You also need to decide how exactly you will use it. Most often it is used when working with materials such as:

Unlike steel structures, a saw can stand out for decades. The design is virtually maintenance free and will always be ready for use when needed. The ramps have sharp ends that eliminate the risk of falling logs.

In addition, we have installed adjustable supports at the beginning and end of the guide, which prevent the ends of the fabric from being covered. The logs are placed on independent beds, the height of which is controlled by a crank handle. Each bed is equipped with its own clamp to prevent the scrap from moving while cutting. Visible and audible height adjustment makes handling much easier.

slats;
thin boards;
logs.

Ready-made drawings can be found on the websites of companies that produce woodworking structures. However, the drawings of the circuits will in any case be only approximate, since they mainly show devices with high power, which will not be a reasonable solution for domestic needs due to their high cost and high fuel consumption.

The compact design makes it easy to handle the log. The cut board sits at your waist and you don't have to bend over or use a lot of force to pull it out of the rack. This means you are saving your back! Many of our customers use stationary trays. But sometimes some of them take a tram with them where it is necessary to wipe the wood, for example, in the forest, in the neighbor's yard or somewhere else. When using the guide and chain for slitting the cut surface is smooth and smooth, comparable to a band saw.

An electric cutting block, for example, but technical data is one thing and practice is another. It all depends on the type of wood being cut. Customers who use our sawmills can say with confidence that they can produce two to four cubic meters lumber in one working day. Of course, you will remember the feeling that accompanies you when you load your first homemade board. The best thing we can distinguish from high-quality products is probably what gives our customers the satisfaction and pride that will surely accompany you after the completion of the first project.

Also, a scheme for making a sawmill can be made independently, armed, for example, with a training video. The most important thing is to place base, bed and skids. You will also need to install a clamping housing between the rail runners. And do not forget to think over the dimensions of your sawmill in advance.

The progress of work on the manufacture of sawmills with their own hands

To make a sawmill from a chainsaw with your own hands, you first need to find a place to work and install, it can be:

The two end supports as standard are the ideal dimensions for the last board. Quick adjustment, adjustable legs. The design is resistant to dirt and corrosion. Quick cutting height adjustment. Suitable for year-round use, even in difficult Scandinavian climates. Two buckles securing the log. Loading ramps according to the standard. The length of the cut in the standard configuration is 5.1 meters. Available accessories: saws, milling machines, band saws etc.

You can easily increase the length of washed logs by adding additional extension pieces. Special rip chains are available for 40 cm, 50 cm and 63 cm rails and are suitable for wiping most log diameters. One of them is to set the saw blade on the washed log. A correctly assembled pattern will be carefully rubbed. The only thing to do is simply adjust the cutting height.

old barn;
hangar;
garage;
canopy.

When doing so, make sure that the machine is safe and sustainable. When working in a closed room, an exhaust must be provided. It is highly undesirable to put the sawmill in rooms with high humidity.

Once you have decided on the future installation site of your sawmill, you can begin to manufacture its base. It should be firmly fixed in order to prevent future hull displacement or vibration.

Stationary sawmill from a chainsaw with a movable carriage

After installation, the track will be completely destroyed. The entire beam structure is made of anodized aluminum profiles and weighs only 52 kg - easily carried by one person and transported on the trunk rack on almost every car. Made from anodized aluminum extruded pattern, it is very strong for its size, expands easily and is able to carry 10 times its weight. The aluminum used to make it is of the highest quality - the same grade used to build aircraft.

The finished elements of the base of the structure must be mounted strictly parallel to the ground, therefore it is recommended to use the building level for this purpose. Fasteners should be as strong as possible, as materials for fastening you can use:

anchor bolts;
hairpins.

When you have finished installing the base, you need to lay the rail track. In this case, the foundation of the structure must be made of metal. Depending on the weight of the sawmill and the conditions of its use, the following products can serve as the basis:

The truck was designed for the operator. Everything is at the right height, and even long hours of work do not burden the spine. It's easy to use - you don't push the saw along the log. For its production, anodized aluminum, stainless steel screws, nylon calipers are used.

His Maintenance should not spend too much time. The washed timber rests on two adjustable adjustable beds. The buckles on the bed block the log and prevent it from slipping. The chainsaw and slicing chainsaw slit logs lengthwise easily and very accurately. The specially designed ratchet chain and blade make it possible to cut straight with very high precision even with poor saw logs.

metal corner;
profile metal pipe;
channel.

Then you need to do the installation of fasteners. Fasteners in this case are a long frame, fixed with different clamps on both sides. It should be installed so that the wood laid on top of the fasteners lies flat. Fasteners should never be circular, otherwise the chains and bars will not work correctly.

Unique, low profile chains

With a comfortable saw blade, an adjustable bed and a convenient arrangement of logs, you can create the best bouquet for your projects. The chains used on this saw have been made by a leading manufacturer of saws and wood cutting accessories. These unique chains guarantee extremely smooth surface after cutting. The low profile makes the knives only 6mm thick. Chains are easy to sharpen. Properly maintained, one chain can cut up to 7 cubic meters of wood.

Log fixing device

This is a craft designed for safety. When cutting, the chain draws the magazine to the supporting structure, holding it firmly in place during cutting. Using the saw requires the use of both hands - this minimizes the risk of an accident while working.

We pass to the moving part of the sawmill. She too has the kind of work to be move along the rails. This structural element is mounted on special rollers, which are fixed on the frame as tightly as possible.

Also, the movable part must contain clips to support the plate. At the same time, they must guarantee the cutting of the material both horizontally and vertically. Fasteners for this part can be different, most often used boxes based on sheet steel or clamps. However, experts recommend using girths based on metal plates for fastening.

Adjustable beds in two scales

The two beds can be independently adjusted up and down. This solution makes it easy to align the magazines for the best cutting results. This feature also allows you to make cuts at different angles. Each bed can be set to two scales.

It also contains practical advice about how to grind. Complex solutions for forest nurseries. Complete range of forestry equipment: chain and cable rails, chain saws, crankshafts, forest tires, forestry chains, lubricating oils, machine lubricants, blades and motor chains.

Do-it-yourself sawmill operation

When you have finished your work on making a sawmill from a chainsaw, you should definitely check it in terms of stability.

Then follows in test mode work with wood. We fix the log on the base and squeeze it with a vise. Additionally, you can put markings in the skids and on the sawmill. For marking, you can use roulette strips or thin strips of metal.

Step by step manufacturing process

Woodworking equipment: logs and wood sorting lines, log logs, horizontal saw blades, vertical saw blades, dryers and masonry, industrial grinders, briquetting lines, granulating plants.

Equipment for biomass production: biomass heaters for disks or drums, wood processors and splitters, winches, mulching and milling machines. On the one hand, this ensures high performance and low impact on environment, and on the other hand, the goal of optimizing costs and improving operational ergonomics.

Slowly start the sawmill and drive it very slowly towards the log to make a test cut. When working, do not forget to wear funds personal protection in order for your face and hands were securely protected.

gloves to protect hands;
glasses;
robe;
sleeves.

Before a trial run of the mechanism, be sure to check how well the log is attached, also check the structure for serviceability and the presence of fuel in it.

The tree can be redeemed on the last chip thanks to new technologies! It is a domestic manufacturer of wood, wood and sawdust. Promotions, events and lottery. 10% or 20% discount, what do you need? We have three days and we have three days of special events.

Traditionally, many related events have been released this year: forums, presentations and seminars. Don't miss out on promotions or a guest raffle! Thursday, March 30 is cell phone day. Friday, March 31 - Day of woodworkers. At the same time, it will also discuss what grant funding opportunities are available to business people in the industry.

The chainsaw itself must be tightly fixed, and its tire must have a central position in relation to the marking of the cut.

We fasten the saw and slowly lead the frame to the tree, and then we start the chainsaw itself and slowly push the frame. Don't make sudden movements to prevent the bars from locking in the cut and don't forget to use a guard for the moving frame. Acrylic or transparent plastic can act as such protection.

On the basis of a chainsaw with your own hands, you can make a lot of useful devices, tools, and even Vehicle. In our article, using the example of assembling a sawmill, you were able to make sure that it is not so difficult.

A manual chainsaw is designed for sawing wood. It is considered a truly versatile tool. However, its function may be insufficient. To increase the processing speed, you can make a sawmill from a chainsaw with your own hands.

Chainsaw sawmill construction

At the first stage, it is recommended to familiarize yourself with the standard factory models. This will help you choose the best design option based on availability. Supplies. It is best to first study the drawings and draw up an individual scheme.

Structurally, any band sawmill consists of a log feed unit and a moving carriage on which a chainsaw is attached. Most often, the cutting blade is located horizontally. In this way, it is convenient to perform sawing to form even boards. The carriage has a mechanism for changing the height of the cutting part.

Any do-it-yourself mini-sawmill from a chainsaw differs from the factory model in the following parameters:

large amount of sawdust. Forced chip vacuum cleaners are provided in the factory settings. Their inlet sockets are attached directly above the treatment area;
carriage stability. At high capacities, the mounting elements may be affected by vibrations. This leads to a change in the original geometric dimensions;
the degree of adjustment of the location of the chainsaw. To increase functionality, it can be installed not only horizontally or vertically, but also at different angles. In do-it-yourself installations, this is difficult to implement.

All factory models undergo mandatory tests, during which shortcomings and defects are revealed. In the future, there is a modification of the sawmill. Changing the configuration of a homemade model is problematic, as this is associated with additional costs.

To perform a large amount of work, you can make an adjusting nozzle that limits the thickness of the log cut. Thus, the formation of boards of the desired thickness occurs.

Accessories for the manufacture of sawmills

An important point in the design is the choice of raw materials for manufacturing. During the operation of a do-it-yourself sawmill, vibrations and loads on structures will inevitably occur. Reliable components must be used to avoid premature failure.

First, a method for processing logs is selected. To perform a large amount of work, it is recommended to make a moving carriage with a fixed chainsaw. Fixation wooden blank performed directly on the lower frame part of the structure.

base platform. For the movement of the carriage, standard rails are usually used. small size. They are interconnected by channels or corners;
moving carriage. The supporting part is made of channel No. 4 or No. 6. Stiffeners - from corners 8 * 8 or 10 * 10 mm;
chainsaw mounting block. Its configuration directly depends on the model of the cutting tool. Chainsaw "Ural" or similar is recommended to be mounted on the base.

All structural components must not be deformed. Otherwise, it will be impossible to make a quality sawmill with your own hands. This applies in particular to the support platform, which ensures uniform movement of the carriage for a smooth cut.

An alternative to the channel can be square pipes. The wall thickness must be at least 1.5 mm. With their help, you can make a carriage.

Do-it-yourself chainsaw sawmill: step by step instructions

For the manufacture will require professional tools. Components are fastened in two ways - using a welding machine and bolts. A powerful electric drill is needed to form the mounting holes. Drills for metal are selected for it. Cutting blanks is performed using a grinder with an appropriate disc.

According to a pre-compiled scheme, blanks should be made, holes are formed in the right places. After that, it is necessary to once again check their dimensions and compliance with the geometry of the original. If there is rust, it should be cleaned with special tools.

Step-by-step instructions for making a sawmill with your own hands.

Base platform. Corners are welded onto one of the rails. Then the second rail is attached.
Moving carriage. Her dimensions must match the distance between the rails. First, the frame part is formed, the wheels are installed. Once again, the dimensions are checked and a trial installation of the carriage on the platform is performed.
Final stage. The mounting assembly for the chainsaw is mounted. If an electric saw is used as a cutting tool, it is necessary to provide a block for connecting to the mains. You can make it yourself or buy it ready-made and fix it in the right place.
Painting. To protect structures from premature rusting, it is first primed, then a layer of paint is applied.

For preliminary tests, it is recommended to use softwoods or mini-blanks. If the cut is accurate and even, you can gradually increase the load. It must be remembered that a do-it-yourself chainsaw sawmill needs periodic inspection of preventive work to maintain the structure in working order.

In the video you can get acquainted with an example of the work of a sawmill: